-
Pelco L560 - page 1
User Instruction & Installation Manual L560 Remote Control 2/3Kw Tungsten Halogen Searchlight Product Reference Number: A2651 – Variable Speed Mo tor Unit 2/3Kw 115/240v Manufacturers details: Distributor details: Manual Part Number: C21514 Issue : 5 Francis Searchlights Ltd Union Road, Bolton Lancashire, BL2 2HJ, UK Tel: +44 (0) 1204 558960 ...
-
Pelco L560 - page 2
CONTENTS 1 - Introduction 2 - Safety Precautions 3 - Technical Information 4 - Unpacking and Installation Instructions 5 - Electrical Installation 6 - Operating Instructions 7 - Fault Finding 8 - Maintenance and Servicing 9 - Wiring Diagram & General Assembly 10 - Spare Parts List ...
-
Pelco L560 - page 3
1 - Introduction It is imperative that this manual is read carefully and understood before installing your equipment. For your future reference please keep this manual in a safe place. Thank you for specifying a product from the Franc is Searchlights range. All Francis products are designed to give complete customer satisfac tion and are manufactur ...
-
Pelco L560 - page 4
2 - Safety Precautions The following instructions must be adhered to, in order to ensure a safe working environment and the safety of the user. Note: When unpacking or manoeuvring the search light into its fixi ng position, suitable lifting points must be used in order to prevent damage to the equipment or personal injury. Prevent rain, snow, c ...
-
Pelco L560 - page 5
3 - Technical Information This product has been designed to operate in acco rdance with the product specification. The L560RC searchlight has t he following features: All marine grade materials and fixings; Parabolic formed aluminium reflector; Powder coated / Stove enamel paint finish; 385° horizontal rotation; Vertical moveme ...
-
Pelco L560 - page 6
4 - Unpacking and Installation Instructions The following instructions should be read and full y understood prior to installing the equipment to ensure that the correct proc edures are followed and all safe ty precautions are observed. Note: If the equipment has been in storage for a considerable amount of time, it is advisable to conduct a routine ...
-
Pelco L560 - page 7
5 - Electrical Installation For safety purposes, only competent personnel should perform the electrical installation. All equipment should be installed to current Electrical Regulations and Standards. In order to obtain the maximum li ght output from the searchlight, it is essential that the full operating voltage of the lamp fitted be applied to t ...
-
Pelco L560 - page 8
Installation Guidelines A typical installation and connection routine fo r the L560RC 2/3Kw searchlight is as follows: Referring to wiring diagram C22978, a supply is fed to the control panel, which then provides a common feed to the motor gearbox and the searchlight. Cables required to be connected by the customer: - 4 core 1.5mm 2 cable from the ...
-
Pelco L560 - page 9
6 - Operating Instructions This equipment is designed for use out of doors, in free air. Never place anything on, or cover the searchlight when in use as this may present a hazard. The searchlight can be remotely positioned via the joystick control panel, with the facility for movement up, down, left and right. The speed of movement depends on the ...
-
Pelco L560 - page 10
weaken the bulb material. Should the bulb be inadvertently touched, remove fingerprints with methylated spirit and a clean, soft paper towel. The bulb should then be wiped with distilled water. NOTE : ALWAYS WEAR MASK AND GLOVES DURING CLEANING); In all circumstances the lamp manufacturers data should be referred to when dealing with lamps. When fi ...
-
Pelco L560 - page 11
7- Fault Finding All fault finding must be conducted by a competent person or qualified Electrical Engineer. Failure of Lamp to light Causes : 1) Power not supplied; 2) Fuse blown; 3) Failed lamp Remedy : 1) Check voltage at supply. If supply is not present t he fault is at the customer supply. If power is present, see remedy 2; 2) Check fuse for v ...
-
Pelco L560 - page 12
8 - Maintenance and Servicing In order to prolong the service life and performance of your searchlight, the following maintenance guidelines are recommended: Maintenance checks should be conducted before ve ry voyage or at least every three months; Before checking, disconnect the equipment from the supply; Visually inspect the condition ...
-
Pelco L560 - page 13
9 - Wiring Diagram and General Assembly Drawing Number Description C22978 Wiring Diagram Lite Range Variable Speed 20 Amp A2651 L560RC 2/3Kw 115/240v Variable Speed General Assembly drawing Control Panel Assembly ...
-
Pelco L560 - page 14
...
-
Pelco L560 - page 15
...
-
Pelco L560 - page 16
...
-
Pelco L560 - page 17
10 - Spare Parts List The following spare parts can be order ed directly from the manufacturer: Part Number Description Searchlight Spares D1823 115v 2Kw G38 Tungsten Halogen Lamp D4604 220/240v 2Kw G38 Tungsten Halogen Lamp D9843 115v 3Kw G38 Tungsten Halogen Lamp D22559 220/240v 3Kw G38 Tungsten Halogen Lamp C23002-00 Selector Switch 20Amp – On ...
¿Tienes una pregunta acerca de Pelco L560?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Pelco L560, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Pelco L560 probablemente compartirá una forma de solucionarlo.