-
Smeg WDI12C1 - page 1
1 WASHER DRYER INSTRUCTIONS MANUAL EN ...
-
Smeg WDI12C1 - page 2
2 EN Contents 1. The new washing system 3 2. Safety warnings 4 3. Installation instructions 7 4. Description of cont rols 14 5. Washing instructions 18 6. Drying instructions 24 7. Cleaning and maintenance 26 8. Troubleshooting 28 9. Control panel symbols 3 0 This appliance is marked according to the European directive 2002/96 /EC on W aste Elect r ...
-
Smeg WDI12C1 - page 3
EN 3 1. THE NEW WA SHING SYSTEM This new washer dryer is the outcome of years of research. The leading-edge design and the quality of the pro duction processes used to manufacture this product e nsure it will give you many years of excellent service. Its concept satisfie s all current and future washing and drying requirements. Its low water, power ...
-
Smeg WDI12C1 - page 4
EN 4 2. SAFETY WAR NINGS Attention! These warnings are giv en for safety reasons. Please read them caref ully before installing an d using the appliance. This manual form s an integr al part of the applianc e and m ust theref ore be k ept intact togeth er with the machine. Before us ing th e appliance, carefully r ead all the instructions contained ...
-
Smeg WDI12C1 - page 5
EN 5 Do not was h petro l-soaked garm ents in the w asher dr yer. Mak e sure there are n o inflam m able items (e.g.: lighters, m atches, etc .) in pock ets before wash ing. If volatile fluids have been used to clean garm ents , make sure that t he substanc es ha ve been rem oved before loading them in the washing m achine. Before loadin g garm ent ...
-
Smeg WDI12C1 - page 6
EN 6 For Great Britain only Warning : this appliance m ust be earthe d. Fuse replacem ent If the m ains lea d of this a ppliance is f itted with a BS 1363A 13amp fused plug, to change a fuse in this t ype of plug use a n A .S.T .A . appro ved f use to BS 1362 t ype and procee d as f ollows: 1. Remove the fus e cover ( A ) and fuse ( B ) 2. Fit repl ...
-
Smeg WDI12C1 - page 7
EN 7 3. INSTALLA TION INSTRUCTIONS Important ! The appliance must be ins talled by a speciali sed technician according to current regulation s. This washer dr y er is ver y heav y. Take care when lifting it. 3.1 UNPACK ING The inside of the machine comprises a moving assembly which is blocked for transport purpose s by the screws ( A) located at th ...
-
Smeg WDI12C1 - page 8
EN 8 3.3 ADDITIONA L IMPORTANT INSTALLATION INSTRUCT IONS 1. Carefully read the installation ins tructions in point 3 on page 6 of the washe r dryer installation manual. 2. After the initial instructions have been adhered to. I.e. removing transit bolts and fitting the adjustable fe et etc. Using a sp irit level, make sure that the wash er dryer is ...
-
Smeg WDI12C1 - page 9
EN 9 3.5 DRA IN CONNECTION 1. Insert the end of the drain hose into a d rain pipe having an internal diameter of at least 4 cm and a height ranging between 50 and 90 cm, or attach it (using t he relative curved plastic profile) to a basin or bath tub. 2. Always chec k that the end of the d rain hose is securely at tached in order to prevent the rep ...
-
Smeg WDI12C1 - page 10
EN 10 3.7 FITT ING THE FURNITURE DOORS Once the w asher dryer has been correctly installed and c ommissioned, the furn iture door can be fitted following the dimensions on the templa te and the instruction enclosed in the washer dryer packa ging. Please note that only furnitu re doors of a thickness betw een 16mm and 21mm are compatible with this w ...
-
Smeg WDI12C1 - page 11
EN 11 3.7.2 Use o f the furniture door fixing template Proceed in the following way when applyin g the wooden panel to the washing dryer: 1. W hen fitting the furniture door utilising the door template you will need to make sure that the bottom and the top of the furniture door will line up with the adjacent cabinet furniture doors . 2. The f inal ...
-
Smeg WDI12C1 - page 12
EN 12 5. Fix the panel to the washing machine following the instructions shown below 3.7.4 Adjusting th e hinges If, after applying the panel to the washing mac hine, it is slightly inclined or off-centre with respect t o the front of the machine, correct its position by adjustin g the mobile part of the hinges (see above ). 3.7.5 Reces sing the ap ...
-
Smeg WDI12C1 - page 13
EN 13 3.7.6 Fitting the plinth The base plinth for kitchen furniture must be removable in the area in front of the washer dryer to allow access for routine maintenance of the d rain pump if it becomes clogged with buttons, fasteners, or similar objects , and for our engineers to be able to remove the washer dryer for service. Please note: our engin ...
-
Smeg WDI12C1 - page 14
EN 14 4. DESCRIPTION OF CONTROLS 4.1 CONTROL PA NEL All the commands and cont rols of the appliance are assembled together on the front panel. Description of contro ls A Open door butt on B ON-O FF and prog ramme sele ction k nob C Delay tim er show n on displa y LED – (onl y for mode ls wit h this opt ion) D T ime remaining sho wn on displ ay LE ...
-
Smeg WDI12C1 - page 15
EN 15 A Open door button Press the button to op en the d oor . Chapter 5 – Washing instructions – explains ho w the door works and ho w to us e it. B ON-OFF and washing and drying programme selection knob This knob lets you: • switch the m achine on and off by moving it in either direction from the OFF position (k nob indicator vertical) • ...
-
Smeg WDI12C1 - page 16
EN 16 I Select spin speed and drying time for delicates button Press the button repeate dly to select the require d spin speed. The fol lowing spin s peeds are a vailable: • 0000: spin d isabled and stop with tub f ull. T he machine does not per form the final spin and ends the washing progr amm e with water in the tu b. To dr ain the water, see ...
-
Smeg WDI12C1 - page 17
EN 17 Economy cycle button - e Press this button for cottons programmes, the machine will perform an e xtended wash at 35°C (biological step) thereby offering good washing pe rformance combined w ith power saving. The m achine then continues the cycle at the selected temperature. N.B.: Press the econ omy c y cle button to o btain a maximum w ashin ...
-
Smeg WDI12C1 - page 18
EN 18 4.2 DETERGENT TRAY This is located to the left of the control panel. Pull i t out to open. The tray com prises four com partments which are mark ed as follows “ 1” : pre-wash d etergent “2” : main wash detergent “ ” or “3” : f abric softener, s tarch, etc. (treatm ent pro ducts). Compartm ent “4” is used f or bleach. If th ...
-
Smeg WDI12C1 - page 19
EN 19 5.2 OPENING THE DOOR The machine is fitted with a safety de vice that prevents the door from opening while it is working. 1. Before o pening the door, wai t 1 or 2 minutes afte r the p rogramme ends (“End” LED on) to allow the safety device to disengage. 2. Make sure there is no water in the tub and that the drum is not moving. Open the d ...
-
Smeg WDI12C1 - page 20
EN 20 Water hardness Hardness level French degree f H German degre e dH Soft Up to 15° Up to 8° Moderatel y hard 15° - 25° 8° - 14° Hard 25° - 40° 14° - 22° Very hard Over 40° Over 22° 5.6 DOSING POWDER DETERGENT S Normally dirty washing 1. Choose a programme without prewash. 2. Pour the total quantity of detergen t indicated on the pac ...
-
Smeg WDI12C1 - page 21
EN 21 Intensive w ashing prog ramme for resistant cotton , coloured or hemp fabrics. Delicate w ashing progra mmes for delicate artificial synthetic fibres , blends or linen fabrics. They prevent the formation of creases that are difficult to remove during ironing. Wool programm e only for garments marked “pu re wool ” washable, treated, shrink ...
-
Smeg WDI12C1 - page 22
EN 22 5.10.3 DELAYED START ( ONLY FOR MODELS FEATURING THIS F UNCTION ) Press the delayed start bu tton ( ). The re lative LED located above the button lights up. The displ ay visualises the time rem aining (hours/min utes) before the selected washi ng programme starts: the display ini tially shows 0 hours 0 minutes for all programmes. Press the bu ...
-
Smeg WDI12C1 - page 23
EN 23 5.13 END OF PROGRA MME The washing programmes are automatically c ompleted, the di splay shows END and the “Time remaining” LED lights up. 1. Turn the programmes knob to OFF to switch off the machine. 2. Open the door. 3. Remove the washing from the drum. 4. Leave the door ajar in order to all ow the inside of the washer dryer to d ry. 5. ...
-
Smeg WDI12C1 - page 24
EN 24 6. USING THE MACH INE FOR DRYING PURPOSES 6.1 GENERA L INFORMATION During drying cycles it is essential that the water tap is open and that th e drain hose is correctly positioned. W ith this machine it is possible to set wash-only programmes, dry-only programmes a nd wash-dry programmes. For the latter programmes, the cycle shifts a utomatic ...
-
Smeg WDI12C1 - page 25
EN 25 During the selection o f the drying programme the L ED of the normal dr y ing programme stays on . This programme indicates an intense d rying cycle and is meant for resistant items and cottons . If a delicate drying c ycle is required (less intensive drying, su itable for delicates and s ynthetics), press the Delicate Drying button. In this ...
-
Smeg WDI12C1 - page 26
EN 26 7. CLEANING AND M A INTENANCE Important – Before cleaning or se rvicing the machine, remove the plug from the socket. 7.1 EXTERNA L CLEANING • Regular and constant cleaning will keep your appliance looking like new. • Clean the outer surfaces with soap an d water and then dry thoroughly with a soft cloth. • Clean parts in plastic with ...
-
Smeg WDI12C1 - page 27
EN 27 3. Pull out the drain hose “A”. Attention: if the hose is h ot it means the water i s hot or boiling. Place a tray on the floor and remove the plug “B” to drain the water. Depending on the quantity of w ater, it may be necessary to empty the tray several times. W hen no more water comes out, pu sh the hose back in and screw back the p ...
-
Smeg WDI12C1 - page 28
EN 28 8. TROUBLESHOOT ING This product complies w ith current s afety regulations governing electrical equipment. For safety reas ons, all technical inspections or repairs must be performed by qualified technicians in order to prevent h azardous situations for users. If the ma chine doe s not work, before calli ng the Service Ce ntre and spending m ...
-
Smeg WDI12C1 - page 29
EN 29 11 The machine does not spin The unb alanced load sensor ha s t riggered because the washing is not uniformly distributed inside the drum. If the washing is w et at the end of the cycle, distribute it well inside t he basket and repeat just the spin cycle. 12 Draining water from the drum In the event of a power failure or a fault i n the appl ...
-
Smeg WDI12C1 - page 30
EN 30 9. CONTROL PA NEL SYMBOLS PROGRAMS OPTIONS OTHER SYMBOLS DRYING WATER INCREASE FABRIC CONDITIONER HAND WASH NO SPIN OR STOP WHIT FULL TUB OPEN DOOR PRE-WASH DELAY TIMER START-PAUSE RINSES DELICATES START DRAIN AND SPIN - e ECONOMY CYCLE WASH SECTION QUICK WASH END COTTON AND COLOURED EXTRA RINSE HEATING WOOL SPIN TIME REMAINING DRYING EASY-IR ...
¿Tienes una pregunta acerca de Smeg WDI12C1?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Smeg WDI12C1, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Smeg WDI12C1 probablemente compartirá una forma de solucionarlo.