-
Avaya 16-300310 - page 1
Avaya Video Conferencing Solutions Quick Setup Release 6.0 16-300310 Issue 1 August 2010 ...
-
Avaya 16-300310 - page 2
© 2010 A vaya Inc. All Right s Reserved. Notice While reasonable ef forts were made to ensure that the information in this document was complete and accurate at the time of print ing, Avaya Inc. can assume no liability for any errors. Chan ges and corrections to the information in this document might be incorporated in fu ture releases. Documentat ...
-
Avaya 16-300310 - page 3
Canadian Department of Communications (DOC) Interference Information This Class A digital appar atus compl ies with Ca nadian ICE S-003. Cet appareil numéri que de la classe A est conforme à la norme NMB-003 du Canada. This equipment meets th e applicable Industry Canada T erminal Equipment T echnical Specifications. This is conf irmed by the reg ...
-
Avaya 16-300310 - page 4
AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 4 Overview This Quick setup guide covers the basic administration t asks to set up SIP and H.323 video endpoint s. For detailed in formation, see A vaya video confere ncing Solutions Networkin g Guide 6.0 . This guide is intended for technicians inst alling the following video ...
-
Avaya 16-300310 - page 5
Configuration of SIP video endpoi nts on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 5 ● Perform a network readiness test or network assessment to ensure your network is capable of su pporting bandwidth demand s of video over IP . Avaya recommends implementing quality of service (QoS) acro s ...
-
Avaya 16-300310 - page 6
Configuration of SIP video endpoi nts on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 6 3 Enabling video for the SIP signaling gro up 1. On System Manager , click Element s > Feature Management > Network - Signaling Group s. 2. On the Signaling Group s page, click the arrow icon next to t ...
-
Avaya 16-300310 - page 7
Configuration of SIP video endpoi nts on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 7 4 Identifying the IP-codec-set 1. Note the values of the Near-end No de Name and Far-end Network Region fields. 2. If the Near-end Node Name field is set to PROCR, the listed value is used. If the Near-end N ...
-
Avaya 16-300310 - page 8
Configuration of SIP video endpoi nts on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 8 Administration of A vaya Series 1000 Vi deo Conferencing and A vaya one-X ® Communicator video end point s and users using System Manager Perform the following step s to configure all A vaya Series 1000 Vid ...
-
Avaya 16-300310 - page 9
Configuration of SIP video endpoi nts on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 9 T able 3: Creating a template 1 Enabling Call Appearace feature 1. T o enable the Call Appearance feature, click Button Assignm ent , and set the main buttons to cal l appr as follows : ● A vaya 1010 : 1 ? ...
-
Avaya 16-300310 - page 10
Configuration of SIP video endpoi nts on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 10 Adding video users T able 4: Adding video users 1 Creating a New User Profile On System Manager , click Users > Ma nage Users and click on New to open the New User Profile page. Fill in the following fie ...
-
Avaya 16-300310 - page 11
Configuration of SIP video endpoi nts on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 11 3 Enabling Session Manager Profile Select the check box corresponding to Sess ion Manager profile and set the following parameters: ● Primary Session Manager : Appropriate option ● Secondary Session Man ...
-
Avaya 16-300310 - page 12
Configuration of SIP video endpoi nts on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 12 Configuring the A vaya Series 1000 Video Conferencing End point s Perform the following step s to configure all A vaya Series 1000 Video Conferencing Endpoint s using the IR Remote Contro l . Y ou can also ...
-
Avaya 16-300310 - page 13
Configuration of SIP video endpoi nts on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 13 3 Enabling SIP protocol Select Communications , cli ck on SIP , and set the following paramete rs: ● SIP Username : ext. This para meter is the same as step 1 of T able 4: Ad ding video users on p age 10 ...
-
Avaya 16-300310 - page 14
Configure H.323 vid eo endpoints on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 14 Configure H.323 video end point s on Communication Manager 6.0 This section provides a set of guidelines to configure video call ing facility on H.3 23 endpoint s with Communication Manager 6.0. Configure Polyco ...
-
Avaya 16-300310 - page 15
Configure H.323 vid eo endpoints on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 15 Configuring Polycom End point s Use this procedure to configure the V ideo cal ling facility for all Polycom end point users. Add Users/st ations to Polycom end point s Use this procedure to add users/st ations ...
-
Avaya 16-300310 - page 16
Configure H.323 vid eo endpoints on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 16 T able 7: Add users/st ations to Polycom end point s 1 Install the Polycom system and connect it to your network. 2 Upgrade the Polycom system sof tware (if necessary). 3 Using a web browser , access the Polycom ...
-
Avaya 16-300310 - page 17
Configure H.323 vid eo endpoints on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 17 Configuring Polycom RMX Series V ideo Conferencing Bridge Plat form Use this procedure to configure the Po lycom RM X series video co nferencing Bridge platform. T able 8: Configuring Polycom RMX Series V ideo c ...
-
Avaya 16-300310 - page 18
Configure H.323 vid eo endpoints on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 18 4 Use the change trunk-group n command (where n is the trunk group you adde d in S tep 2) to add members to the trunk gro up. The number of members depends on the maximum simultaneou s calls an RMX support s. 5 ...
-
Avaya 16-300310 - page 19
Configure H.323 vid eo endpoints on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 19 Configuring Ad-hoc V ideo Confer encing for a Polycom RMX V ideo Conferencing Bridge Plat form T o configure Ad-hoc conferencing for a Polycom RMX video co nferencing bridge platf orm, perform the following step ...
-
Avaya 16-300310 - page 20
Configure H.323 vid eo endpoints on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 20 4 Use the add video-bridge command to configure a video bridge for the RMX system. Set the following para meters: ● Name to the name for this video b ridge (for example, Ad Hoc video Bridge - RMX). ● Max Por ...
-
Avaya 16-300310 - page 21
Configure H.323 vid eo endpoints on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 21 7 For the Conference IVR Service, perform the following steps: ● Under the W elcome tab, disable th e Enable Welcome Messages check box ● Under the Conference Chairperson t ab, disable the Chairperson messag ...
-
Avaya 16-300310 - page 22
Configure H.323 vid eo endpoints on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 22 Display Cap acity for Ad-hoc video Conferencing. T o display the capacity for Ad-hoc video confe rencing on the Communication Mana ger system: T able 10: Display cap acity for Ad-hoc video conferencing. 1 Use th ...
-
Avaya 16-300310 - page 23
Configure H.323 vid eo endpoints on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 23 Administering Polycom PathNavigator/ CMA Gatekeepers Perform the following step s to configure a Polycom PathNaviga tor/CMA Gatekeepers: T able 1 1: Administering Polycom PathNavigator/ CMA Gatekeep ers 1 Use th ...
-
Avaya 16-300310 - page 24
Configure H.323 vid eo endpoints on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 24 4 Use the add signaling- group command to add a signaling group for the gatekeeper . Set the following p arameters: ● Group T ype: H.323 ● IP video: y ● Priority video. If you want all incomi ng calls t o ...
-
Avaya 16-300310 - page 25
Configure H.323 vid eo endpoints on Communication Man ager 6.0 AVTS R 6.0 Quick Setup For feedback, use doc ument@avaya.com August 2010 25 Configuring A vaya one-X ® Communicator Avaya one-X ® Communicator can be configured with eit her SIP or H.323 protocol. Ensure the check box corresponding to Enable V ideo is selected on the endpoint. T o con ...
¿Tienes una pregunta acerca de Avaya 16-300310?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Avaya 16-300310, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Avaya 16-300310 probablemente compartirá una forma de solucionarlo.