-
Royal Sovereign 1050 - page 1
Royal Sovereign LAMINATORS OWNER'S MANUAL RSH-1050/1650 ,RSR-685/1050 PLEASE READ AND SAVE INSTRUCTIONS - 1 - ...
-
Royal Sovereign 1050 - page 2
TOPICS PAGE INSTRUCTION ----------------------------------------------------------------------- 3 SAFETY PRECAUTIONS ----------------------------------------------------------- 3 CHARACTERISTICS ----------------------------------------------------------------- 4 SPECIFICATIONS --------------------------------------------------------------------- 4 ...
-
Royal Sovereign 1050 - page 3
Thank you for purchasing a Royal Sovereign Roll Laminator. It has been designed and manufactured to provide years of continuous service in the professional environment. To insure high quality lamination, please read this instruction manual thoroughly. This manual will provide you with complete operating and maintenance information. For additional p ...
-
Royal Sovereign 1050 - page 4
RS Roll Laminator Line is advanced laminators with time transcendental desi g n, utilizin g the latest in laminatin g technolo gy . It is desi g ned for y ou to set tem p erature and s p eed as necessar y and have the machine remember y our settin g s. Also, y ou can laminate an y thin g at hi g h s p eed, regardless of thickness of material and ty ...
-
Royal Sovereign 1050 - page 5
NO RSR-1050 RSR-685 1 2 3 4 5 7 8 9 10 11 12 13 14 ○ ○ ○ ○○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ X ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ X ○ X X ○ ○ ○○ PART NAME FRAME-GUIDE,PAPER ○ ○ NAMES OF MAJOR PARTS OF MACHINE ○○ FOOT SWITCH RSH-1050 ○ RSH-1650 ○ ○○ ○ TA ...
-
Royal Sovereign 1050 - page 6
1. Disassemble both the Right cover and the Left cover. (Note :Turn the fastening nut of the Emergency switch counterclockwise and disaasemble the Emergency switch before disassembling the Right cover.) 2. Disassemble the Rear cover. 3. Disassemble the power switch bracket which is located at the left side of the machine. 4. Put the Plate-Rewinder ...
-
Royal Sovereign 1050 - page 7
take -up motor. 7. Assemble the Right cover letting the wires go through the slot which is located at the rear side of the Right cover. 8. Put the Power switch bracket on the Plate-Rewinder L and fasten it with two M4 screws. How to install the unwinder Female Connector from take-up motor Male Connector from rewinder motor Power switch bracket Plat ...
-
Royal Sovereign 1050 - page 8
1. Put the Plate-Unwinder R on the inner side of the frame as shown in the following figure and fasten it with four M6 hexagonal bolts. 2. Put the Plate-Unwinder L on the inner side of the frame as shown in the following figure and fasten it four M6 hexagonal bolts. SETTING UP FILM 주 름 방 지 부 열 판 주 름 방 지 부 열 판 L C D 표 ? ...
-
Royal Sovereign 1050 - page 9
1. Set the glossy side of upper/lower film to face the heat. ( Glossy side is PET film and matte side is thermal polymer laminating film.) 2. Like picture 1, insert core into the left side of upper/lower film shaft. 3. Like picture 2 and 3, insert core into the right side of upper/lower film. 4. Like picture 4 and 5, adhere core closely. (Make the ...
-
Royal Sovereign 1050 - page 10
1. HOT FILM RSH-1050/1650 RSR-685/1050 1. Insert bar into the core of the roll film then place the bar on the machine. 2. Place the Pressure Lever (on the right side of machine) to the open mode at 15mm. 3. Insert a piece of wide cardboard (guiding paper/carrier) between the rollers. 4. Pull the film from the upper roller passing over the upper idl ...
-
Royal Sovereign 1050 - page 11
RSH-1050/1650 RSR-685/1050 1. Set up cold film below the upper bar of the machine (Set the same as method of HOT film for protect paper of lower part) 2. Set the pressure Lever to the 15mm, open mode 3. Insert a piece of wide cardboard (guiding paper/carrier) between the rollers 4. Pull the film from the upper roller passing over the upper idle bar ...
-
Royal Sovereign 1050 - page 12
1. For setting, pull the pressure lever out and turn the lever to following the indication 2. Open/15mm : for laminating 15mm(0.6") thick board (RSH-1050/1650) 3. 10~13mm : for laminating 10~13mm （ 0.4" to 0.5") thick board 4. 5~7mm : for laminating 5~7mm(0.2" to 0.27") thick board 5. 1mm : for laminating 1mm(40mil) thick ...
-
Royal Sovereign 1050 - page 13
speed and temperature of rollers each by each by the LCD controller. And with memory function, you don’t need to set machine every time you laminate. 1.LCD WINDOW 1. Initial display status. ***Terms*** BUTTON LCD DISPLY - 13 - ...
-
Royal Sovereign 1050 - page 14
It displays you the last working condition when turned on. 2. Is displayed when the preset temperature is reached. 3. Blinking Indicates to wait till blinking stops. Current temperature is higher or lower than the preset temperature. 4. Saving electricity status. 5. Temperature 1) Shows the preset temperature 2) You can check the current temperatur ...
-
Royal Sovereign 1050 - page 15
: Speed controller : Choose memorized working condition : ① Increase temperature ② Increase speed ③ Restore the memorized working setting : ① Decrease temperature ② Decrease speed ③ Restore the memorized working setting : Cold and Hot mode change : Check current temperature : Saving electricity while the machine is not being operated. : ...
-
Royal Sovereign 1050 - page 16
to 160°C (320°F). 2. Temperature setting of upper roller Press and you will see the LCD screen is blinking 6 times. Before blinking is finished, press or to set the temperature 3. Set temperature of lower roller Press and choose the arrow button the same way to set temperature of upper roller. 4 Each time you press the button, it will change 1°C ...
-
Royal Sovereign 1050 - page 17
1.Operator can memorize 9 working conditions. 2.Choose working condition by pressing and button after pressing button. and speed, press button. 3.It is memorized if buzzer is ringing with blinking. * If you change the temperature or speed when LCD screen is still blinking, you have to press button after changing. 4.When you memorize another working ...
-
Royal Sovereign 1050 - page 18
blink five times. 2.After this, it automatically returns to the previous state. 1.You can do cold lamination with this function. 2.Press the button to show "Cold" on the display. 3.Speed will always show 2. 4.Speed can be varied 1 or 4 by selecting button. 5.You release the machine from cold mode by pressing button. 6.Everytime you press ...
-
Royal Sovereign 1050 - page 19
condition wouldn’t work. Press the button and it will revert to the previous working. 3. When machine runs, you can’t change it to the mode. In this case, press the button and turn the machine to the mode. 1. When press button the present numbers of length and papers laminated will be shown on the screen. 2. When you want to return to working m ...
-
Royal Sovereign 1050 - page 20
2. Set the pressure lever to the “Laminating mode” 3. Increase roller temperature. If you already memorized special working condition, press button and choose right condition by using or button. 4. When it’s ready, you will see ready sign on the screen and the buzzer will ring. 5. Press the button. If rollers don’t run, check the emergency ...
-
Royal Sovereign 1050 - page 21
If it happens, the speed needs to be lowered by one speed level and started again after signal on the LCD window. 3. In case of wrinkling or rolling of film due to wrong position of document, is needed to be keeping pushed in order that document could come out to the front with buzzer sound. 4. When document is much smaller than film, you should pl ...
-
Royal Sovereign 1050 - page 22
4. After pressing the button choose and set proper speed by using the and button. 5. It is when ready is show on the screen and the buzzer rings three times. sound three times. 6. Turn on the take up device and set the proper film tension by pressing the button. Lower tension would make better operation. 7. Set document on the table. You should all ...
-
Royal Sovereign 1050 - page 23
4. Press Foot Switch one time for "RUN", press one more time for "STOP". (Don't keep pressing) 5. After use of Remote Control, attach it to the left side of rear of machine **Cross Cutter** 1. It is on the back side of the machine. 2. After lamination, move cutter to a point about 1/3 of the width of lamination 3. Grasp fil ...
-
Royal Sovereign 1050 - page 24
Extreme Heat Will Cause Injury 3.Place the machines on the plated place so that 4.Make certain that the machine is connecterd to an ade q uate p ower souce. 5.Do not use any other purposes other than Lamination. 1.Do not allow the machine to run with only one roll of film installed. The melted resin will adhere to one roller and ruin future laminat ...
-
Royal Sovereign 1050 - page 25
4. It may stay at STAND-BY mode. press the STND-BY button *Hot roller is not heater 1. It is set at the cold mode 1. Change the function to hot up. 2. Memorized temp may be lower lamination. than atmosphere temp. 2. Set proper temperature for the work *Wrinkled lamination 1. Film tension is not proper, too 1. Adjust film tension. result tight. *Res ...
-
Royal Sovereign 1050 - page 26
a Sovereign authorized service representative, or damage caused by a natural calamity such as fire or earthquake and etc… 3. Customers will bear the expense of Transportation fee and delivery fee of the damaged machine. 110 5 1 75 micron Remark Func'No Preset Speed & Temperature Adjustment Speed NO User Temp Speed Temp Film thickness 1 3 ...
-
Royal Sovereign 1050 - page 27
120 5 115 4 2 140 3 9 130 4 7 135 3 9 250 micron (10 mil) 2 75 micron (3 mil) 8 200 micron (8 mil) 3 80 micron (3.2 mil) 100 micron (4 mil) 6 150 micron (6 mil) 7 4 5 3 120 4 4 125 5 5 175 micron (7 mil) 125 micron (5 mil) 125 3 6 8 - 27 - ...
¿Tienes una pregunta acerca de Royal Sovereign 1050?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Royal Sovereign 1050, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Royal Sovereign 1050 probablemente compartirá una forma de solucionarlo.