-
HP LASERJET P2055 - page 1
HP ® LASERJET P2035 • 2055 CAR TRIDGE REMANUF ACTURING INSTRUCTIONS TONER CARTRIDGE HP ® LASERJET P035 • 2055 PRINTER 3232 West El Segundo Blvd., Ha wthorne, California 90250 USA • Ph +1 42 4 675 3300 • Fx +1 424 675 3400 • t echsuppor t@uninetimaging.com • www . uninet imaging.com © 2009 UniNet Imaging Inc. All trademark names and a ...
-
HP LASERJET P2055 - page 2
REMANUF ACTURING THE HP LASERJET P2035 • 2055 TONER CAR TRIDGE By Mike Josiah Figures abov e show the dif f erent physical sizes of the two cartridges. The car tridges are similar in design to the 1 160/1 320 car- tridges, but are not inter changeable. The drum drive gear is a complet ely new syst em. The actual drive gear is a floating type that ...
-
HP LASERJET P2055 - page 3
SUPPLIES REQUIRED 11 0g HP-P2035 toner f or the CE505A car tridge (2,300 pages) 290g HP-P2035 toner f or the CE505X car tridge (6,500 pages) Replacement Chip New Drum (Optional) Uninet #1 33 72 - HP P 2035, 2055 Unidrum ™ gearless recommended. Wiper Blade (Optional) Dr . Blade (Optional) Magnetic roller (Optional) Sealing Strip (Optional) Cotton ...
-
HP LASERJET P2055 - page 4
2. Drill a shallow hole on each side of the cartridge as indicated by the arr ows. Figures shown bef ore drilling. Af t er drilling. HP P2035 • 2055 CARTRIDGE REMANUF ACTURING INSTRUCTIONS 3232 West El Segundo Blvd., Ha wthorne, California 90250 USA • Ph +1 42 4 675 3300 • Fx +1 424 675 3400 • t echsuppor t@uninetimaging.com • www . unine ...
-
HP LASERJET P2055 - page 5
3. Push the pins out with a jew eler’s screwdriver . With the hole in this location by just pushing the scre wdriver in, the pins will be pushed out. Remo ve the pins. 4. Separate the tw o halves. 5. With a flat head screwdriv er , press the drum axle pin out from the inside of the cartridge wall as shown. There is a small s houl- der visible tha ...
-
HP LASERJET P2055 - page 6
The drum hub on the opposite side is w elded. The weld can be brok en or drilled out, but there is a good chance that the hub will either warp if pried off, or will be hard to align if drilled out. 6. Remo ve the drum. This is a good time to look at the ne w drive gear(s). This is a complet ely new syst em. New drums and gears are being dev eloped. ...
-
HP LASERJET P2055 - page 7
1 0. Coat the wiper blade with your preferred lubricant. Install the blade and 2 screws. 11 . Re-install the cleaned PCR. Note that a ne w OEM PCR has a small amount of conductive grease on the black (contact) side. 12. Re-Install the OPC Drum and metal axle pin. The metal axle pin should ha ve a small amount of conductive grease on the tip. Remo v ...
-
HP LASERJET P2055 - page 8
13. Slice the two tabs off each location as shown on the left (Seal) end cap. Use a square blade X-Acto knif e to slice off the tabs. NOTE : Both the end caps are plastic welded in place. The only wa y to open them up is to cut the w elds and carefully drill them out. We ha ve f ound the lef t (Non-Gear) side is the best side to do this on. 1 4. Us ...
-
HP LASERJET P2055 - page 9
1 7 . Remo ve the Magnetic roller driv e gear . The end cap will keep the bushing in place. 18. Remo ve the DR. Blade and two scre ws. 19. Clean out an y remaining toner from the hopper . Note the Dr . Blade seal. It is a sticky substance that can be clean with alcohol if toner gets on it. 20. Fill through the Mag r oller opening with 11 0g of P203 ...
-
HP LASERJET P2055 - page 10
2 1. If you are going to seal the cartridge, there is a white plas- tic shelf that needs to be remo ved. The shelf is held on with double sided tape. It can be gently pried of f with a small scre w- driver . 22. Re-install the whit e plastic shelf. If the adhesive is not working, replace it with a good double sided tape. This shelf helps with the f ...
-
HP LASERJET P2055 - page 11
26. Install 2 small screws int o the holes previously drilled out. Leav e the top 3rd hole alone! (This w eld was brok en when the end cap was remo ved). A screw here will int er fere with installing the car tridge in the printer . In our tests, the two screws will hold the end cap on with no pr oblems. 25. Re-assemble the t oner hopper section. Pl ...
-
HP LASERJET P2055 - page 12
2 7 . Place the tw o halves together , make sure that the two springs are aligned, and insert the two pins. Make sure that the pins are slightly pushed in so that they do not int er f ere with installing the car tridge in the printer . 28. Install the drum cov er; make sure the spring is situat ed correctly. HP P2035 • 2055 CARTRIDGE REMANUF ACTU ...
-
HP LASERJET P2055 - page 13
TROUBLESHOOTING Repetitiv e Defect Char t OPC Drum: 75mm Low er Fuser r oller 63mm Upper F user film 5 7mm Registration r oller 43mm Magnetic Roller 42mm T ransfer roller 39mm PCR 38mm RUNNING TEST P A GES P2030 Series Only T o run the Demo Page, mak e sure that the ready light is on, and briefly press the GO button. The Demo Page will print out. T ...
-
HP LASERJET P2055 - page 14
RUNNING THE CLEANING P A GE P2030 Only T o run the Cleaning Page, mak e sure that the ready light is on. Inser t a transparency in the paper tray . Open the printer -driver pr oper ties screen and click on the device settings tab. In the cleaning page area press star t. P2050 Only Inser t a transparency in the paper tra y. Open HP t oolbox FX and c ...
¿Tienes una pregunta acerca de HP LASERJET P2055?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con HP LASERJET P2055, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con HP LASERJET P2055 probablemente compartirá una forma de solucionarlo.