-
Tannoy I9 - page 1
B i9 USER MANUAL ...
-
Tannoy I9 - page 2
CONTENTS 1. Introduction 2. Unpacking 3. Low Impedance or 70.7/ 100V distributed line operation. 4. Amplification and Powe r Selection (Low Impedance Mode) 4.1 Connectors & Cabling for Low Impedance Operation 5. Voltage and Power Select ion (Distributed Line Operation) 5.1 Connectors and Cabling for Distributed Li ne Operation 6. Polarity Check ...
-
Tannoy I9 - page 3
1. Introduction The Tannoy i9 installation loud speaker is designed fo r use in applications requiring high quality music and speech, where wi de a nd controlled coverage is required. The i9 comprises f our 130 mm (5”) low fr equency drivers and three 25mm (1”) high frequency drivers. The LF and HF source s are positioned as line source. The co ...
-
Tannoy I9 - page 4
When the number of speakers is large over lon g cable runs, it is recommended that a distributed (70.7V/100V) system be used. For distri buted line, the cable need not have a large cross sectional area as for low impedanc e, resultin g in savings in cable cost. All speakers are placed in parallel with the outpu t of the amplifier, allowing easy ins ...
-
Tannoy I9 - page 5
Figure 4d : Series Parallel Combination: 8 Ω When operating in low impedan ce mode the ro tary switch on the ba ck of the cabinet as shown in Figure 4a , below should be se t to ‘8 ohm’ Figure 4a 100V A 70V B D C 8ohm OFF Transformer Tappings A B D C 7.5W 15W 30W 60W 15W 60W 30W 4.1. Connectors & Cabling for Low Impedance Operation The i9 ...
-
Tannoy I9 - page 6
Cable choice consist s mainly of selecting the correct cross se ctional area in relation to the cable length and the l oad impedance. A sm all cross sectional area would i ncrease the cables’ series resi stance, inducing power loss a nd response variations (dampin g factor). Connectors should be wi red with a minimum of 2.5 mm 2 (13 gauge) cable. ...
-
Tannoy I9 - page 7
5.1 Connectors and Cabling for Distributed Line Operatio n Connections are identical t o those used in low impedance mode, via the4-pole Neutrik Speakon connectors (see section 4.1): Pin 1+ is Positive Pin 1- is Negative Distributed line systems are much mo re effici ent in power transfer and do not re quire as large cables as in lo w impedance ...
-
Tannoy I9 - page 8
. 6. Polarity Checking It is most important to check the pola rity of the wiring. A simple method of doing this without a pulse based pol arity checker for LF units is as follows: Conne ct two wires to the + ve and - ve terminals of a PP3 battery. Apply the wire that is connected to the + ve terminal of the battery to the speaker cable leg which yo ...
-
Tannoy I9 - page 9
! 11. Rigging & Suspension 11.1 General Safety Adv ice The Tannoy Professional hardwa re covered in this guide has be en designed to offer quick, simple, cost effective and secure soluti ons for m ounting specifically the Tannoy i9 Professional loudspeaker. This hardware has been d esigned and manufactured with a high safety load factor for its ...
-
Tannoy I9 - page 10
11.2 i9Y - Wall mount Bracket Fig 3. Ï Ð Í Î The i9’s proximity to the wall can be adjusted to allow aiming of the loudspeaker in the horizontal pl ane (fig 4 & 5). Fig 5. Fig 4. The Main body of the bracket (1) should be fixed first to the wall in the desire d location using all six fixing points. Secure fixings to the build ing structur ...
-
Tannoy I9 - page 11
11.3 i9 MAB- Multiple Angle Bracket The i9 MAB is designed to provide a number of flexib le mounting angles when the i9 is suspended from overhead cables. The i9 MAB is attached to the cabinet as shown with the supplied hex socket screws and washe rs supplied. Remove the original M10 counter sunk screws from the top and bottom of the i9, position t ...
-
Tannoy I9 - page 12
12. i9 Service Parts & Acces sories Part Number Description 7900 0657 LF Driver Type 1277 7900 0674 High frequency Unit 7300 0853 Crossover Kit 8001 3020 i9Y - Wall mount Bracket (Black) 8001 3030 i9Y - Wall mount Bracket (White) 8001 3070 i9 MAB- Multiple Angle Bracket (Black) 8001 3080 i9 MAB- Multiple Angle Bracket (White) 8001 1930 Tannoy T ...
-
Tannoy I9 - page 13
14. Declaration of Confor mity The following apparatus is/are manufa ctured in the United Kingdom by Tannoy Ltd of Rosehall Industrial estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirem ents of the European Electromagnetic Compatibility Standar ds and Dire ctives relevant to Domestic Electrical Equipment. The apparatu s ...
-
Tannoy I9 - page 14
B Tannoy Loudspeakers are manufa ctured in Great Britain by : Tannoy Ltd, Ros ehall Industria l Estate, Coatbridge, Strathclyde, ML5 4TF, SCOT LAND Telephone: +44 (0)1236 420199 Fax: +44 (0)123 6 428230 Tannoy North America Inc, Suite 1. 335 Gage Avenue, Kitchener, Ontario, CANADA, N2M 5E1 Telephone: (519) 745 1158 Fax: (519) 745 2364 Tannoy Nederl ...
¿Tienes una pregunta acerca de Tannoy I9?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Tannoy I9, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Tannoy I9 probablemente compartirá una forma de solucionarlo.