-
Cisco Systems ASASSMCSC10K9 - page 1
Q UICK S TART G UIDE Cisco ASA Services Module 1 Information About the ASA Servi ces M odule in the Switch Network 2 Verifying the Module Installation 3 Assigning VLANs to the ASA Services Module 4 Using the MSFC as a Directly-Connected Rou ter 5 Logging Into the ASA Services Module 6 Configuring ASDM Connectivity 7 Launching ASDM 8 Running the Sta ...
-
Cisco Systems ASASSMCSC10K9 - page 2
2 Updated: May 15, 2013, 78-19998-02 1 Information About the ASA Services Module in the Switch Network For switch and software compatibility with the ASA Services M odule (ASASM), see the following: http://www.cisco.com/en/US/docs/securi ty/asa/compatibility/asamatrx.html . Th e switch runs Cisco IOS software on both the swit ch supervisor engine a ...
-
Cisco Systems ASASSMCSC10K9 - page 3
3 For multiple context mode, if you place the MSFC or router behind the ASASM, you should only connect it to a single context. If you connect it to multiple con texts, the MSFC/router will route between the contexts, which might not be your intentio n. The typical scenario for multiple contexts is to use a router in front of all the contexts to r o ...
-
Cisco Systems ASASSMCSC10K9 - page 4
4 2 Verifying the Module Installation Verify that the switch acknowledge s the ASASM and has bro ught it onli ne. (If you n eed to install your ASASM, see the module installation guide on Cisco. com.) Ent er the following command to ensure that the Status column shows “Ok” for the ASASM: show module [ switch { 1 | 2 }] [ mod-num | all ] For a s ...
-
Cisco Systems ASASSMCSC10K9 - page 5
5 4 Using the MSFC as a Directly-Connected Router If you want to use the MSFC as a directly -connected router (for ex ample, as the default gateway connected to the ASASM outside interface), then add an ASASM VLAN interface to the MSFC as a switched virtual interface (SVI). By default, you ca n add only one SVI; to add multiple S VIs, and understan ...
-
Cisco Systems ASASSMCSC10K9 - page 6
6 5 Logging Into the ASA Services Module From the switch CLI, you can connect to a virtual console session on the A SASM: Command Purpose Step 1 service-module session [ switch { 1 | 2 }] slot number Example: Router# service-module session slot 4 hostname> Connects to the ASASM. For a switch in a VSS, enter the switch argument. You access user E ...
-
Cisco Systems ASASSMCSC10K9 - page 7
7 Logging Out of the ASA Services Module If you do not log ou t of the ASASM, the console conn ection persists; there is no timeout. To end t he ASASM console session and access the switc h CLI, perform the follow ing steps. To kill another user’s active connecti on, which may have been unintentionally l eft open, see the configuration guide. Ste ...
-
Cisco Systems ASASSMCSC10K9 - page 8
8 Step 2 Do one of the following to configure a manag ement interface, depending on you r mode: Routed mode: interface vlan number ip address ip_address [ mask ] nameif name security-level level Example: hostname(config)# interface vlan 1 hostname(config-if)# ip address 192.168.1.1 255.255.255.0 hostname(config-if)# nameif inside hostname(config-if ...
-
Cisco Systems ASASSMCSC10K9 - page 9
9 Step 4 http server enable Example: hostname(config)# http server enable Enables the HTTP server for ASDM. Step 5 http ip_address mask interface_name Example: hostname(config)# http 192.168.1.0 255.255.255.0 inside Allows the management host to access ASDM. Step 6 write memory Example: hostname(config)# write memory Saves the configuration. Step 7 ...
-
Cisco Systems ASASSMCSC10K9 - page 10
10 7 Launching ASDM Using ASDM, you can use wizards to configure basic and advanced features. ASDM is a graphical user interface that allows you to manage the A SAS M from any lo cation by using a web browser. See the ASDM release notes on Cisco.co m for the requirements to run ASDM. Step 1 On the PC connected to the ASASM ma nagement VLAN, launch ...
-
Cisco Systems ASASSMCSC10K9 - page 11
11 8 Running the Startup Wizard Run the Startup Wizard so that you can customize the security policy to suit your deployment. Using the startup wizard, you can set the following: Step 1 If the wizard is not already running, in the main ASDM window, choose Wizards > Sta rtup Wizard . Step 2 Follow the instructions in the S tartup Wizard to config ...
-
Cisco Systems ASASSMCSC10K9 - page 12
12 9 (Optional) Allowing Access to Public Servers Behind the ASA Services Module The Public Server pane automatically configures the security policy to make an inside server accessible from the Internet. As a business owner, you might have internal network services, such as a web and FTP server, that need to be available to an outside user. You can ...
-
Cisco Systems ASASSMCSC10K9 - page 13
13 10 (Optional) Running Other Wizards in ASDM You can optionally run the following additional wizards in ASDM: • High Availability and Scalability Wizard Configure active/active or active/standby failover, or VPN cluster loa d balancing. • Packet Capture Wizard Configure and run packet capture. The wizard will r un one packet capture on each o ...
-
Cisco Systems ASASSMCSC10K9 - page 14
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco .com/go/trademarks . Third-party trad emarks mentio ned are the p roperty of t heir respecti ve owners. The use of th e word partn er does not i mply a partner ...
¿Tienes una pregunta acerca de Cisco Systems ASASSMCSC10K9?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Cisco Systems ASASSMCSC10K9, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Cisco Systems ASASSMCSC10K9 probablemente compartirá una forma de solucionarlo.