-
Hitachi NB5741XD - page 1
• Single-phase Input 100V Class Manual No . NB5741XD • December 2003 Hitachi Industrial Equipment Systems Co., Ltd. HIT A CHI L100-M Series In ver ter Quic k Reference Guide ...
-
Hitachi NB5741XD - page 2
1 Caution: Be sure to r ead the L100 In verter Manual and follow its Cautions and W arni ngs for the initial product installation. This Quick Refe r ence Guide is intended for r eference use by e xperienced users in servicing existing installations. P ower Cir cuit T erminals –002NFE/NFU, –004NFE/NFU, –005NFE Jumper (/) +1 + – L1 L2 N /L3 U ...
-
Hitachi NB5741XD - page 3
2 Contr ol Circuit T erminals Te r m i n a l Name Description Ratings and Notes P24 +24V for logic inputs 24VDC supply , 30 mA max. (Notes: Do not use for network power Do not short to terminal L) 1, 2, 3, 4, 5 Intelligent (program- mable) discrete logic inputs 27VDC ma x. (use P24 or an external supply reference d to terminal L), 4.7k Ω input im ...
-
Hitachi NB5741XD - page 4
3 O Analog input, voltage 0 to 9. 6 VDC range, 10VDC nominal, 12 VDC max., input impedance 10 k Ω H +10V analog reference 10VDC nominal, 10 mA max. AL0 Relay common contact C ontact rating Max resistive load = 250V A C, 2.5A; 30VDC 3A; Max inductive load = 250V A C, 0.2A; 30VDC 0.7A Minimum load = 5VDC 100mA, 100V A C, 10mA AL1 Relay contact, nor ...
-
Hitachi NB5741XD - page 5
4 Basic Wiring Diag ram The following wirin g diagram shows the power and motor c onnec- tions for basic operation. The optio nal signal input wiring supports external Fwd and Re v Run command, and a speed potentiometer . (L1) R (L2) S (N/L3) T (T2) V (T3) W (T1) U Motor Fo rwa r d L O H Rev erse Alarm contacts, 1 Form C Run signal F requency arriv ...
-
Hitachi NB5741XD - page 6
5 In ver ter K eypad Operatio n • Run/Stop LED – ON when the inverter output is ON and the motor is de veloping torque, and OF F when the in verter output is OFF (Stop Mode). • Progra m/Monitor LED – ON when the in verter is ready for parameter editing (Program Mode) . It is OFF when the parameter display is monitoring data (Monitor Mode). ...
-
Hitachi NB5741XD - page 7
6 • Potentiometer – Allows an operator to directly set the motor speed when the potentiometer is enab led for output frequ ency control. • Potentiometer Enable LED – ON when the potentiometer is enabled for value entry . • Para meter Displ ay – A 4-digit, 7-segmen t display for parame- ters and function codes. • Display Units: Hertz/A ...
-
Hitachi NB5741XD - page 8
7 Ke ypad Navigation Map c9 1 c0 1 1 2 b 89 b 01 1 2 A9 8 A0 1 1 2 1 2 1 2 1 2 C– – 1 2 b –– 1 2 A– – F0 4 F0 1 1 2 d 09 d 01 1 2 o.0 12 3 . 4 Edit 1 2 Increment/ decrement val ue Write data to EEPROM Displa y data Monitor Mode Program Mode FUNC. STR FUNC. FUNC. 1 2 Return to parameter list FUNC. FUNC. Store as powerup default power dow ...
-
Hitachi NB5741XD - page 9
8 P owerup T est The Power up T est procedure uses minimal parameter settings to run the motor . The proced ure describes two alternati ve methods for commanding the in verter: via the in verter keypad , or via the logic termin als . • Check po wer input and motor output wiring (see page 4 diagram). • If using logic terminals for testing, v eri ...
-
Hitachi NB5741XD - page 10
9 Err or Codes The L100 series inv erters will trip on ov er-current, over -voltage, and under-voltage to protect the in verter . The motor output turns OFF , allowing the motor to free-run to a stop. Press the Stop/Reset ke y to reset the inv erter and clear the er ror . Basic Error Codes Error Code Name Probable Cause(s) E01 Over curr ent event w ...
-
Hitachi NB5741XD - page 11
10 Erro r T rip Conditions Use function code D_08 to access th e error trip conditions for the current error as shown in the table below . Use the Up and Down arrow ke ys to scroll through the trip condition parameters. E35 Thermistor • Thermistor input, [THM] and [L], is over the temp. threshold --- Under -voltage (bro wn- out) with output shuto ...
-
Hitachi NB5741XD - page 12
11 Restoring Factory Default Settings Action Display Function/Parameter Press , or as needed. b -- “B” Group selected Press . b 01 First “B” Group parame- ter Press/hold until... b 85 Coun try code for initialization selected Press . If setting is correct, then skip next step. 02 00 = Japan 01 = Europe 02 = United States T o change country ...
-
Hitachi NB5741XD - page 13
12 Note: After initializing the inverter , us e the P owerup T est on pag e 8 to get the motor running again. Pa ra m e te r T a b le s “D” Gr oup: Monitoring Functio ns Func. Code Name / Description Units D_01 Output frequency monitor Hz D_02 Output current monitor A D_03 Rotation direction monit or — D_04 Process v ariable (PV), PID feedbac ...
-
Hitachi NB5741XD - page 14
13 T rip History Na vigation Map E0 7 60 . 0 1 2 4. 0 0 27 0 . 0 1 2 1 2 d 08 1 2 o.0 0 Displa y data Monitor Mode 1 2 FUNC. FUNC. d 09 ____ No Error code Output frequency at trip point Motor current at trip point DC bus voltage at trip point FUNC. Ye s No error Error (n-1) ex is ts ? No Ye s E0 3 E0 5 ____ No history FUNC. Error (n-2) ex is ts ? N ...
-
Hitachi NB5741XD - page 15
14 Parameter tables for user-settable functions follo w these conven- tions: • Some parameters specify an op tion code. Where applicable, the options codes will be in a bulleted list in the Name/Description column. • The default v alues apply to all models unless otherwise noted for each parameter... –FE (Europe) / – FU (U.S.) / –FR (Japa ...
-
Hitachi NB5741XD - page 16
15 “A” Group: Standard Functions Func. Code Name / Description Default Va l u e –FE / –FU / –FR Set Va l u e A_01 Frequency source setting • 00 Ke ypad pot entiometer • 01 Control terminal • 02 Function F_01 setting 01 / 01 / 00 A_02 Run command source setting • 01 Input terminal FW or R V (assign- able) • 02 Run k ey on keypad, ...
-
Hitachi NB5741XD - page 17
16 A_41 T orque boost method selection • 00 Manual torque boost • 01 Automatic torque boost 00 A_42 Manual torque boost value 11 A_43 Manual torque boost frequ ency adjust- ment 10.0 A_44 V/f characteristi c curve selection • 00 V/f constant torque • 01 V/f v ariabl e torque 00 A_45 V/f gain setting 100 A_51 DC braking enable • 00 Disable ...
-
Hitachi NB5741XD - page 18
17 “B” Gr oup: Fine-tuning Fu nctions A_82 A VR voltage select 230/230/200 400/460/400 A_92 Acceleration (2 ) time setting 15.0 A_93 Deceleration (2 ) time setting 15.0 A_94 Select metho d to switch to Acc2/Dec2 profile • 00 2CH input from terminal • 01 transition frequency 00 A_95 Acc1 to Acc2 frequency transition point 0.0 A_96 Dec1 to De ...
-
Hitachi NB5741XD - page 19
18 B_12 Lev el o f electronic ther mal setting Rated current of each in verter B_13 Electronic thermal character istic • 00 Reduced torque • 01 Const. torque 01 / 01 / 00 B_21 Overload restriction operatio n mode • 00 Disable d • 01 Enabled for accel and constant speed • 02 Enabled for constant speed only 01 B_22 Overload restrictio n set ...
-
Hitachi NB5741XD - page 20
19 “C” Gr oup: Intelligent T erminal Functions B_88 Rest art mode after FRS • 00 Restart from 0Hz • 01 Restart from frequency detected from actual speed of motor 00 B_89 Data select for di gital operator OPE-J • 01 Output frequency (D_01) • 02 Output current (D_02) • 03 Motor direction (D_03) • 04 PID PV feedback (D_04) • 05 Input ...
-
Hitachi NB5741XD - page 21
20 C_21 T erminal [11] functi on Six option codes av ailable (see page 22) 01 C_22 T erminal [12] function 00 C_23 [FM ] signal selection Three option codes av ailable (see page 22) 00 C_31 T erminal [11] active state (–FU) • 00 Normally open (NO) • 01 Normally closed (N C) — / 00 / — Reserv ed (–FE / –FR) 00 / — / 00 C_32 T erminal ...
-
Hitachi NB5741XD - page 22
21 Intelligent Input T erminal Listing Symbol Code Input T erminal Name FWD 00 Forw ard Run/Stop R V 01 Re verse Run/Stop CF1 02 Multi-speed select, Bit 0 (LSB) CF2 03 Multi-speed select, Bit 1 CF3 04 Multi-speed select, Bit 2 CF4 05 Multi-speed select, Bit 3 (LSB) JG 0 6 Jogging 2CH 09 2-stage accel and decel FRS 11 Free-run stop EXT 12 Exte rnal ...
-
Hitachi NB5741XD - page 23
22 Intelligent Output T erminal Listing Analog Inpu t Configuration The following tables show the parameter settings required for vari- ous analog input signal types. Analog Output Function Listi ng The following table shows all thre e functions av ailable for assign- ment to the analog output terminal: • T er minal [FM], option set by C_23 Symbo ...
-
Hitachi NB5741XD - page 24
23 Notes: ...
¿Tienes una pregunta acerca de Hitachi NB5741XD?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Hitachi NB5741XD, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Hitachi NB5741XD probablemente compartirá una forma de solucionarlo.