-
Channel Master 100 - page 1
Instruction and Assembl y Manual TYPE 900 - .9m TYPE 100 - 1.0m TYPE 120 - 1.2m SMC ANTENNA WITH AZ/EL CAP MOUNT .90m, 1.0m & 1.2m SMC ANTENNA SYSTEM WITH AZ/EL CAP MOUNT 8000284 Rev . H 3/99 1315 Industrial Park Drive , P .O . Bo x 1416 Smithfield, N.C . 27577 U .S.A. (919) 989-2242 ■ F ax (919) 989-2200 (UK) Limited Premier Business P ark, ...
-
Channel Master 100 - page 2
VSA T ANTENNA/MOUNT/LNB LIMITED TWEL VE (12) MONTH W ARRANTY This CHANNEL MASTER ® equipment is warranted to be free from defects in material and workmanship under norma l use and ser vice. CHANNEL MASTER shall repair or replace def ective equipment, at no charge , or at its option, refund the purchase pr ice, if the equipment is returned to CHANN ...
-
Channel Master 100 - page 3
D ANGER!!! W A TCH FOR WIRES! Installation of this pr oduct near power lines is danger ous. For y our own saf ety , f ollow these impor- tant safety rules. 1. P erf or m as many functions as possib le on the ground. 2. W atch out f or ov erhead power lines . Check the distance to the pow er lines before starting installation. W e recommend you sta ...
-
Channel Master 100 - page 4
GR OUND POLE INST ALLA TION 2 ³⁄₈ ” O .D. x 72” LONG 72 37 d 36 1" to 2" SLOPE FOR W A TER RUN OFF GRADE BELO W FROST LINE O V AL END MIN. DIA. 2 ³⁄₈ " O .D. PIER FOUND A TIONS 72 37 d 48" 1" to 2" SLOPE FOR W A TER RUN OFF GRADE BELO W FROST LINE O V AL END MIN. DIA. NOTE: 48" may be increased, conc ...
-
Channel Master 100 - page 5
L A d 36 (B) 1" to 2" SLOPE FOR W A TER RUN OFF GRADE #3 REBAR X DIA. OF PIER, INSERT THRU HOLE IN TUBE & CENTER BELO W FROST LINE MIN. DIA. NO TE: Clearance increases at elevations greater than 23˚. 3" O .D. PIER FOUND A TIONS L A d 48" (B) 1" to 2" SLOPE FOR W A TER RUN OFF GRADE #3 REBAR LENGTH = d MIN LESS 1&q ...
-
Channel Master 100 - page 6
ASSEMBL Y AND INST ALLA TION The AZ/EL Cap Mount can be installed on a 2 ³⁄₈ ”o r 3 ”O . D . ground tube, roof , or wall mount depending on model. The appropriate mount should be assembled and in place bef ore installing the AZ/EL cap . As the AZ/EL cap mount is f actor y preassembled, there is no assembly required f or the mount. ASSEMBLI ...
-
Channel Master 100 - page 7
IMPORT ANT : Sealing RF coaxial connector: The copper-plated center conductor in the RF coaxial cable , which connects receiver to LNB , can e xperience electrolysis corrosion at the LNB connector . Moisture and DC current cause this type of corrosion. T o pre vent corrosion, apply a mod - erate coat of silicon grease to the center conductor and th ...
-
Channel Master 100 - page 8
ANTENNA ALIGNMENT PR OCEDURE Alignment with the satellite is obtained by setting polar- ization, ele vation and azim uth. Char ts 1, 2 & 3 are to deter mine the values f or your ear th station antenna site. “ ∆ L ” is the difference betw een the ear th station antenna site longitude and the satellite longitude. Use “ ∆ L ” and your ...
-
Channel Master 100 - page 9
0 1 02 03 04 05 06 07 08 0 0 20 40 60 80 10 30 50 70 90 ANTENNA FEED NORTHERN SOUTHERN POLARIZA TION CHART SIGN V ALUES (+ OR -) HEMISPHERE HEMISPHERE ANTENNA SITE WEST OF SA TELLITE LONGITUDE - + ANTENNA SITE EAST OF SA TELLITE LONGITUDE + - EARTH ST A TION LA TITUDE IN DEGREES NORTH OR SOUTH OF EQU A TOR POLARIZA TION + OR – (SEE ILLUSTRA TION) ...
-
Channel Master 100 - page 10
90 80 70 60 50 40 30 20 10 0 1 0 2 0 3 04 05 06 0 7 08 0 0 EARTH ST A TION LA TITUDE IN DEGREES NORTH OR SOUTH OF EQU A T OR ELEV A TION IN DEGREES " L" IS THE DIFFERENCE BETWEEN THE EAR TH ST A TION ANTENNA SITE LONGITUDE AND THE SA TELLITE LONGITUDE ELEV A TION CHAR T CHART 2 5 ° 10 ° 15 ° 20 ° 25 ° 30 ° 35 ° 40 ° 45 ° 50 ° 55 ...
-
Channel Master 100 - page 11
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 180 190 200 210 220 230 240 250 260 270 180 170 160 150 140 130 120 110 90 270 [AZIMUTH COLUMN READING WHEN EARTH ST A TION IS WEST OF SA TELLITE] [AZIMUTH COLUMN READING WHEN EARTH ST A TION IS EAST OF SA TELLITE] EARTH ST A TION ANTENNA LA TITUDE (IN DEGREES NORTH OR SOUTH OF EQ UA TOR) EARTH ST A ...
-
Channel Master 100 - page 12
P AR TS AND HARD W ARE LISTING 2 3 25 2 26 3 23 24 3 23 2 17 22 21 20 19 17 2 3 16 17 18 19 1 FIG. 4.0 - AZ/EL CAP MOUNT ITEM P ART NO . DESCRIPTION QTY . 1 2070022-01 BOL T -ROUND HEAD , SQU ARE NECK M8X60 4 2 2603300-01 W ASHER-LOCK M8 ( ⁵⁄₁₆ )8 3 2460800-01 NUT -HEX M8 4 16 2010105-03 HOUSING AZ/EL 1 17 2503300-01 WASHER FLA T M8 ( ⁵? ...
-
Channel Master 100 - page 13
7 15 8 5 6 9 11 13 12 4 6 14 CLAMP SURF ACE 9 6 7 10 Junction Bloc k (9) P AR TS AND HARD W ARE LISTING FIG. 4.1 - ANTENNA, ANTENNA FEED (LNB) & FEED SUPPORT LEGS ITEM P ART NO . DESCRIPTION QTY . 4 2020329-07 LEG BO TT OM (.90m) 1 4 2020329-02 LEG-BOTT OM-FEED (1.0m) 1 4 2020329-03 LEG-BOTT OM-FEED (1.2m) 1 5 3040642-02 REFLECT OR-SMC-1.0m 1 5 ...
-
Channel Master 100 - page 14
HARD W ARE SORTER M8 x 60mm Round Head Square Neck Bolt Item 1, PN 2070022-01 M4 x 12mm Phillips Head Screw PN 2430070-04 M8 x 20mm Round Head Square Neck Bolt Item 19, PN 20700022-03 M8 x 35mm Round Head Square Neck Bolt Item 20, PN 2070022-05 W asher , Flat - ¹⁄₄ " x ³⁄₄ " OD Item 10, PN 2502700-01 W asher , Flat - ¹⁄₄ &q ...
¿Tienes una pregunta acerca de Channel Master 100?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Channel Master 100, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Channel Master 100 probablemente compartirá una forma de solucionarlo.