-
Porter-Cable 4634 - page 1
Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT Please make certain tha ...
-
Porter-Cable 4634 - page 2
2 Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are ...
-
Porter-Cable 4634 - page 3
3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● lead from lead-based paints ● crystalline silica from bricks and cement and other masonry pro ...
-
Porter-Cable 4634 - page 4
4 Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS 1) Work area safety a) Keep work a ...
-
Porter-Cable 4634 - page 5
5 d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose ...
-
Porter-Cable 4634 - page 6
6 ADDITIONAL SPECIFIC SAFETY RULES SAVE THESE INSTRUCTIONS! 1. Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. 2 . Verify the direction ...
-
Porter-Cable 4634 - page 7
7 2 ........................ two-phase alternating current 2 N ........................ two-phase alternating current with neutral 3 ........................ three-phase alternating current 3 N ........................ three-phase alternating current with neutral ........................ rated current of the appropriate fuse-link in amperes ....... ...
-
Porter-Cable 4634 - page 8
8 FOREWORD Porter-Cable screwdrivers are designed to install or remove various sizes and types of fasteners. FUNCTIONAL DESCRIPTION CARTON CONTENTS Carton contents include the screwdriver, an instruction manual, and a parts list. NOTE: This tool is shipped completely assembled. No assembly time or tools are required. ASSEMBL Y OPERA TION TO ST ART ...
-
Porter-Cable 4634 - page 9
9 Never attempt to change direction of rotation while the switch is “ON” . To do so, may damage interlock feature built into switch. Be sure that the switch is “OFF” and the motor has completely stopped before changing the direction of rotation. 4 . VARIABLE SPEED – As the trigger switch is squeezed, the tool speed increases. 1. Pull the ...
-
Porter-Cable 4634 - page 10
10 CHANGE BIT HOLDER – MODELS 4630, 4634 DISCONNECT TOOL FROM POWER SOURCE. 1. Pull the Depth Stop Assembly (A) Fig. 4 from the clutch housing. 2. Pull the bit holder (C) Fig. 4 out. If it is difficult to remove, grip it with pliers and pull. NOTE: You can remove the bit (B) Fig. 4 from the bit holder by pulling it straight out. 3. Push the new b ...
-
Porter-Cable 4634 - page 11
11 DRIVING SELF-DRILLING/T APPING SCREWS – MODELS 4640 NOTE: Maximum size screws for use with this tool are #12 wood screws and 1/4" self-drilling/tapping screws. These screws drill and tap their own hole as they are driven. This differs from self-tapping screws in that pre-drilled holes for tapping are not required. To drive these screws: 1 ...
-
Porter-Cable 4634 - page 12
12 BRUSH INSPECTION (If applicable) For your continued safety and electrical protection, brush inspection and replacement on this tool should ONLY be performed by an AUTHORIZED PORTER-CABLE SERVICE STATION or a PORTER-CABLE • DELTA FACTORY SERVICE CENTER. At approximately 100 hours of use, take or send your tool to your nearest authorized Porter- ...
-
Porter-Cable 4634 - page 13
13 SERVICE A complete line of accessories is available from your Porter-Cable • Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier. Since accessories other than those offered by Porter-Ca ...
-
Porter-Cable 4634 - page 14
14 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material du ...
-
Porter-Cable 4634 - page 15
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , D ...
¿Tienes una pregunta acerca de Porter-Cable 4634?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Porter-Cable 4634, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Porter-Cable 4634 probablemente compartirá una forma de solucionarlo.