-
Broan 418 - page 1
EC62 SERIES INTENDED FOR DOMESTIC COOKING ONL Y INST ALLER: LEA VE THIS MANU AL WITH HOMEO WNER. HOMEO WNER: USE AND CARE INFORMA TION ON P A GE 12. Broan-NuT one Canada Inc.; Mississauga, Ontario www .broan.ca 877-896-1119 www .broan.ca REGISTER Y OUR PRODUCT ON LINE A T : www .broan.ca SV08970 re v . 05 HB0091 INST ALLA TION INSTR UCTIONS READ AN ...
-
Broan 418 - page 2
W ARNING W ARNING - 2 - T O REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJUR Y TO PERSONS, OBSER VE THE FOLLO WING: 1. Use this unit only in the manner intended by the manuf acturer . If you hav e questions, contact the manuf acturer at the address or telephone number listed in the warranty . 2. Bef ore ser vicing or cleaning unit, s witch power of ...
-
Broan 418 - page 3
HL0126 - 3 - - EC62 SERIES PO WER P A CK SYSTEM - 3¼” X 10” A DAPTER /D AMPER ( SUPPLIED WITH SINGLE BLOWER POWER P ACK ) S INGLE B LOWER (600 CFM , SUPPLIED WITH POWER P ACK ) D UAL B LOWER (1000 CFM , SUPPLIED WITH POWER P ACK ) L6230SS, L6236SS OR L6242SS C USTOM H OOD L INER (O PTIONAL ) S T AND ARD 3¼” X 10” D UCT ( NOT INCLUDED ) EC ...
-
Broan 418 - page 4
- 4 - 1. PREP ARE THE INST ALLA TION 2. INST ALL DUCTWORK AND ELECTRICAL WIRING Plan where and how the ductwork will be installed. Access to the top of the power pac k is preferred f or connection of ductwor k. Install proper-sized ductwork, elbows and roof or w all cap for the type of po wer pack y ou are installing. If installing EC621306SS singl ...
-
Broan 418 - page 5
NOTE: The dual blow er model has the same dimensions than the single blow er model, but does not hav e a hor izontal discharge . Ref er to single blow er power pack illustr ation for bac k and side views , and discard hor iz ontal discharge measurements. 3. PREP ARE CUST OM HOOD The custom hood must be constructed to fit the shape and total weight ...
-
Broan 418 - page 6
- 6 - 4. INST ALL CUST OM HOOD LINER (OPTIONAL) The liners are specially designed to protect the e xter ior base of the custom hood. T o order , refer to the table belo w to find the r ight liner model n umber according to the width of the custom hood nominal width. T o view specific model inf ormation, including depths f or each liner models, visi ...
-
Broan 418 - page 7
Using a Rober tson or a Phillips no . 2 screwdriver , remove both wiring cov er retaining screws ( A ). Detach it from the power pac k and set aside with its screws . Then, remov e both sides screws ( B ) retaining the front panel to the po wer pack. Carefully detach the front panel from the power pac k and set aside with its screws . HD0 3 65 - 7 ...
-
Broan 418 - page 8
- 8 - 12. INST ALL THE ADAPTER AND THE DAMPER (DUAL BLOWER MODEL ONL Y) Using 2 no . 8 x 3/8’ ’ screws from par ts bag, assemble the adapter on the top of the po wer pack. Seal all joints with metal f oil duct tape to eliminate air leaks. Install 10” damper inside the VERTICAL ductw ork that will be attached to power pack. Do not install in a ...
-
Broan 418 - page 9
- 9 - 14. INST ALL THE POWER P ACK Lift the power pac k in custom hood until the bottom of the clasping springs (2 per side) rests on the top of the custom hood base (gre y zone in illustration at right). F rom inside the power pac k, using provided no . 8-10 x 1/2” scre ws, mount the pow er pack to the custom hood base. T o do so, r aise the fro ...
-
Broan 418 - page 10
- 10 - 16. REINST ALL THE BLOWER (SINGLE BLOWER MODEL, HORIZONT AL DISCHARGE ONL Y) The single blo wer power pac k is factory shipped for a vertical discharge installation. F or a hor iz ontal discharge installation, the blo wer must be flipped. Using a 5/16” sock et, or a Phillips no. 2 or a Rober tson no . 2 screwdriver , secure the blow er to ...
-
Broan 418 - page 11
19. REINST ALL FIL TERS 1. Using a Phillips no . 2 screwdriver , assemble the knob to each filter . NO TE: The screw MUST BE on filter tabs side . See illustration at r ight. CA UTION Remove pr otective plastic film covering filter s before installing them. HO01 3 9 - 11 - 2. Rest rear filters edge on filter springs ( B ) in the power pac k. 3. Usi ...
-
Broan 418 - page 12
21. USE AND CARE P ower P ack Cleaning Stainless steel cleaning : Do: • Regularly wash with clean cloth or rag soak ed with warm water and mild soap or liquid dish detergent. • Alwa ys clean in the direction of original polish lines. • Alwa ys rinse well with clear water (2 or 3 times) after cleaning. Wipe dry completely . • Y ou ma y also ...
-
Broan 418 - page 13
- 13 - 24. W ARRANTY 23. WIRING DIAGRAM K1 BLK BLACK BLU BLUE BRN BROWN GRY GREY ORG ORANGE RED RED WHT WHITE YEL YELLOW COLOR CODE LINE GROUND NEUTRAL 120 VAC WHT BLK YEL WHT YEL BLK YEL WHT J1 WHT J2 GRY BRN RED BLK ORG WHT BLU WHT BLU ORG BLK WHT BLU WHT ORG BLK WHT BLU WHT ORG BLK 1 2 3 1 2 3 4 5 M M BLOWER MOTOR TRANSFORMER LAMP LAMP OPTIONAL ...
-
Broan 418 - page 14
- 14 - 25. SERVICE P ARTS EC621306SS EC622301SS 1 1 HL0169 2 3 4 2 7 9 9 10 10 11 K EY NO . P ART NO . D ESCRIPTION Q TY . ( P OW ER P ACK M ODEL ) EC621306SS EC622301SS 1 SV13296 A DAPTER /D AMPER 3¼” X 10” 1 - SV08541 A DAPTER 10” R OUND - 1 2 SV09226 E LECTRONIC C ONTROL WITH C HROMED B UTT ONS AND B LUE LED S 1 1 3 SV05917 S OCKET 2 2 4 ...
¿Tienes una pregunta acerca de Broan 418?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Broan 418, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Broan 418 probablemente compartirá una forma de solucionarlo.