-
BCS Oil-Fired - page 1
W ARNING Improper installation, adjustment, alteration, service or maintenance can cause serious in- jury or property damage. Refer to this manual. For assistance or additional information, con- sult a qualified installer or service agency . W ARNING If the information in these instructions is not followed exactly , a fire or explosion may result c ...
-
BCS Oil-Fired - page 2
Page 2 Oil-Fired BCS Storage Capacity (gal.) BTUH (Thousands) Firing Rate (GPH) Hot Outlet T emperature Rise (F) OIL-FIRED BCS Instr uction Manual Return Cold Inlet Recovery (GPH) B D 20e-BCS 20 60 0.43 3 ⁄ 4 '' 3 ⁄ 4 '' 3 ⁄ 4 '' 90° 66 3 8 1 ⁄ 4 ' ' 20'' 6'' 11'' 1 4 3 ...
-
BCS Oil-Fired - page 3
Oil-Fired BCS Page 3 WHEN YOU RECEIVE Y OUR NEW W ATER HEA TER Check the new equipment to see if all components are in good condition and were not damaged in shipment. The water heater and burner may be shipped as separate units. The aquastat and immersion well are packed with the burner . If damage is obser ved or parts appear to be missing, conta ...
-
BCS Oil-Fired - page 4
Page 4 Oil-Fired BCS 1. Cut a 7" O.D. opening in the preferred wall and provide a minimum of 1 ⁄ 2 " clearance of non-combustible space around the Balanced Flue. The opening should allow for a 1 ⁄ 2 " downward pitch to the outside for drainage of any condensate in the Balanced Flue. 2. Insert the Balanced Flue from the inside thr ...
-
BCS Oil-Fired - page 5
Oil-Fired BCS Page 5 CONNECT W ATER PIPING Be careful not to apply any heat to the water heater nipples. Install dielectric unions and shut off valves on both hot and cold water lines. 40 BCS models are equipped with a brass inlet bushing in- stalled in the tank. Heaters equipped with this bushing are marked next to the inlet by the decal shown on ...
-
BCS Oil-Fired - page 6
Page 6 Oil-Fired BCS FRESH AIR INTAKE VENT Proper sealing of the fresh air intake vent material is important, but temperature is not an issue. Failure to properly seal the inlet venting subjects the burner to possible reverse drafts after burner shutdown— a hazardous condition with the possibility of creating a fire . Use only solid or flexible m ...
-
BCS Oil-Fired - page 7
Oil-Fired BCS Page 7 CONNECT THE OIL LINE Gravity System: The oil burner is normally equipped with a single-stage pump equipped for one line (gravity) flow . Use 3 ⁄ 8 " O.D. or larger soft copper tubing and attach with flared fittings. DO NOT USE COMPRESSION FITTINGS. Install the shut off valve and oil filter in the oil line. Follow instruc ...
-
BCS Oil-Fired - page 8
Page 8 Oil-Fired BCS PLA CE W A TER SYSTEM IN OPERA TION 1. Fill the tank with water , opening a hot water faucet to allow trapped air to escape from the heater . Open the cold water inlet valves. Shut off each faucet as it delivers water that is free of air . Inspect for leaks. Never operate an empty or partially full heater . 2. Be sure the oil t ...
-
BCS Oil-Fired - page 9
Oil-Fired BCS Page 9 MEASURING THE OUTCOMING W ATER TEMPERA TURE, CON’T W ARNING: Hydr ogen gas can be produced in a hot water system served by a heater that has not been used for a long period of time (generally two weeks or more). Hydr ogen gas is extremely flammable. T o reduce the risk of injury, open the hot water faucet at the highest locat ...
-
BCS Oil-Fired - page 10
SERVICE 1. Check the fuel supply , electrical wiring, fuses, and make sure the temperature control is calling for heat. 2. If the motor runs but there is no flame, remove the electrode assembly , clean, readjust, and check the porcelain for cracks. Replace if necessary . Check the ignitor to see if it is produc- ing a spark. ( Use extreme caution? ...
-
BCS Oil-Fired - page 11
Oil-Fired BCS Page 11 COMP ANY’S RESPONSIBILITY The company’ s responsibility is to repair or replace, at our option, with the prevailing compa- rable Bock model, any part of the equipment, including the tank, sold by the company which proves to be defective in material or workmanship during the warranty period, when installed in accordance wit ...
-
BCS Oil-Fired - page 12
OUR TO T AL W ARRANTY COMMITMENT W e will not assume, nor authorize any person to assume for us, any other liability in connec- tion with the sale or operation of Bock W ater Heaters. Any implied warranties, including mer- chantability or fitness for a particular application, imposed on the sale of this heater under laws of the state of sale are li ...
-
BCS Oil-Fired - page 13
Oil-Fired BCS Page 13 BOCK OIL-FIRED W ATER HEA TER ...
-
BCS Oil-Fired - page 14
Page 14 Oil-Fired BCS Balanced Flue ™ BURNER WIRE DIA GRAM Models 20, 32,40,51,120,190E-BCS Carlin EZ-T emp Control ...
-
BCS Oil-Fired - page 15
Oil-Fired BCS Page 15 EXP ANSION T ANK (OPTIONAL) IF ANY OF THESE DEVICES ARE USED, A PROPERL Y SIZED EXP ANSION T ANK MUST BE INST ALLED. ...
-
BCS Oil-Fired - page 16
Page 16 Oil-Fired BCS Form # 23390 Rev 3 3/2007 BCS AND RADIANT HEA T Radiant heating: An in-floor hot water space heating system A Bock high-efficiency water heater and zoned radiant heating— Bock&Radiant —make perfect partners for cost-effective personal comfort that heats both space and water . Bock&Radiant uses functional hot water ...
¿Tienes una pregunta acerca de BCS Oil-Fired?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con BCS Oil-Fired, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con BCS Oil-Fired probablemente compartirá una forma de solucionarlo.