Español dropdown-ico

Manual de instrucciones a/d/s/ PH30.2

24 de páginas 1.65 mb
Descargar

Pasar a la página of 24

Summary
  • a/d/s/ PH30.2 - page 1

    analog and digital systems PH30.2 owner's manual front_cover.qxd 10/26/56 5:13 AM Page 2 ...

  • a/d/s/ PH30.2 - page 2

    table of contents introduction 1 about this manual 2 features of your PowerPlate™ 2 warning and tips 3 mounting locations 3 system planning 4 system configurations 5-9 amplifier and crossover contr ols 10-11 installation 12 controls and connections 12-13 signal sources 14 internal signal routing 15 multi-cross™ cr ossover and configurations 16 ...

  • a/d/s/ PH30.2 - page 3

    about this manual T o get the most from your a/d/s/ PowerPlate™, we recommend that you have the installation performed by your qualified authorized a/d/s/ dealer . If this unit is installed by your dealer , we will extend the warranty to two years instead of the standard one-year . However , if you feel that you have the necessary skills and pref ...

  • a/d/s/ PH30.2 - page 4

    war nings and tips Always disconnect the battery ground wir e before doing any work on your vehicle. Reconnect the cable only after the installation is complete and the wiring has been checked to make sure that ther e are no problems. If your radio featur es a code type security system, be sure you know the code befor e disconnecting the battery! Y ...

  • a/d/s/ PH30.2 - page 5

    system planning Proper system planning is the best way to maximize your PowerPlate’ s™ performance. By planning your installation carefully you can avoid situations wher e the performance or the reliability of your system is compromised. Y our authorized a/d/s/ dealer has been trained to maximize your system’ s sonic potential. Y our a/d/s/ d ...

  • a/d/s/ PH30.2 - page 6

    system configurations All a/d/s/ PowerPlates™ provide extensive featur es, which make a variety of system configurations possible. It is not feasible to cover all of the possibilities within the few pages of this manual. There ar e a few system configurations, however , which are extr emely popular when used alone or as a "building block&quo ...

  • a/d/s/ PH30.2 - page 7

    System 2 - PH30.2 used in 5-channel mode with the AC502 providing level contr ol for bridged channels 5 and 6. 1 and 2 are high-passed for fr ont speaker and channels 3 and 4 are high-passed for r ear speakers. Although shown as a 4-channel input, the source unit can be either 2 or 4-channel depending on the setting of the 2/4 channel switch. Syste ...

  • a/d/s/ PH30.2 - page 8

    System 4 - PH30.2 used in 4-channel mode with high-pass tweeters and bandpass midrange. Channels 1and 2 are configur ed high-pass for the main tweeters and channels 3 and 4, and 5 and 6 are configur ed bandpass for main midrange. Channels 4 and 6 are contr olled by the 3/4 level control and cr ossover section. The amplifier is configured for a 2-ch ...

  • a/d/s/ PH30.2 - page 9

    System 6 - PH30.2 used in 3-channel bridged mode with two channels dedicated for the main speakers and one bridged channel pair used for a subwoofer . Channels 1/2, and 3/4 are configur ed high-pass for the main front speakers using a single pair of RCA inputs to pr oduce a bridged mono output. 8 left satellite right satellite subwoofer 70A ...

  • a/d/s/ PH30.2 - page 10

    System 7 - T wo PH30.2’ s are used. The first PH30.2 is configured the same as system 4 and the second PH30.2 is configured similar to system 5. The first amplifier drives the fr ont midrange and tweeters and the second amplifier drives the rear speakers and the subwoofer . 9 front right tweeter front left midrange front right midrange front left ...

  • a/d/s/ PH30.2 - page 11

    10 ...

  • a/d/s/ PH30.2 - page 12

    1. 2ch/4ch input switch- Leave this switch OUT if you are using 4 channels of input. Push the switch IN if you have only 2 channels of input to send input 1 and 2 to channels 3 and 4, respectively . (see page 15) 2. 5/6 source- This switch selects the sour ce for channel 5 and 6. Select the input source as input RCA 1 and 2, the summed signals fr o ...

  • a/d/s/ PH30.2 - page 13

    installation 1. Disconnect the battery ground cable. Reconnect the gr ound cable only after the installation is complete and the wiring has been checked to make sure that ther e are no pr oblems. If your radio features a code type security system, be sur e you know the code before disconnecting the battery! 2. Run a minimum A WG #8 power wire dir e ...

  • a/d/s/ PH30.2 - page 14

    speaker connections for stereo configurations Minimum r ecommended impedance is 2 ster eo. Speaker terminals accept up to A WG #12 speaker wire. speaker connections for bridged configurations Minimum recommended i mpedance is 4 when bridged to subwoofers and 4 when bridged to full range speakers. Speaker terminals accept up to AWG #12 speaker wir e ...

  • a/d/s/ PH30.2 - page 15

    signal sour ces Due to the wide input level adjustment range, all a/d/s/ PowerPlates™ can be driven with either a conventional preamplifier drive signal or the amplifier signal fr om a powered sour ce unit. This makes the PowerPlate™ perfect for upgrading an OEM (Original Equipment Manufacturer) ster eo system while retaining the factory instal ...

  • a/d/s/ PH30.2 - page 16

    inter nal signal r outing 2-channel/4-channel input switch - routes RCA input fr om channels 1/2 to channels 3/4. When the switch is engaged, channel 1 input is routed to both amplifier channels 1 and 3 with input channel 2 routed to amplifier channels 2 and 4. Switch in the engaged position. When the switch is disengaged, channels 1, 2, 3, and 4 r ...

  • a/d/s/ PH30.2 - page 17

    multi-cr oss™ cr ossover configuration xover control 1/2- The cr ossover selection for channels 1 & 2 has three options: When the switch is in the left position, the crossover section of the amplifier is bypassed. Channels 1 & 2 output is full range. When the switch is in the center position, channels 1 & 2 are filter ed through a 12d ...

  • a/d/s/ PH30.2 - page 18

    Constant Bass cir cuit T o mix sub-bass information into channels 1/2 and 3/4, select a low- pass crossover point, and use the level contr ols to set the level of sub- bass signal sent to channels 1/2 and 3/4. using the AC502 (optional) The AC502 remote level contr ol, available as an accessory from your a/d/s/ dealer , may be used with your PowerP ...

  • a/d/s/ PH30.2 - page 19

    adjusting input sensitivity The input sensitivity setting is important to ensure pr oper performance, low noise levels, and maximum system reliability . As a general rule, components at the "front end" of the system should be set as high as possible with the input sensitivity of the amplifier set as low as possible while still providing a ...

  • a/d/s/ PH30.2 - page 20

    tr oubleshooting symptom possible cause action to take no output low or no remote turn-on check remote turn-on voltage input output at amplifier and correct as needed fuse blown check power wire integrity and reversed polarity , repair as needed and replace fuse power wires not connected check power wire and gr ound connections and repair or replac ...

  • a/d/s/ PH30.2 - page 21

    symptom possible cause action to take distorted output (cont’d) speakers are blown check system with known working speakers and repair or replace as needed poor bass response speakers wired with wr ong check speaker polarity and polarity causing cancellation repair as needed at low frequencies crossover set incorr ectly r eset cr ossovers referri ...

  • a/d/s/ PH30.2 - page 22

    specifications amplifier section PH 30.2 power output 4 (watts)1 6 channel 6 x 75 3 channel 3 x 250 power output 2 (watts)2 6 x 112.5 fuse type 70 A maxi dimensions 13" x 19 7/8" x 2" distortion all channels driven <0.1% 20Hz to 20,000Hz frequency r esponse ±1dB 10Hz to 30,000Hz signal-to-noise ratio full >90dB bandwidth @ rat ...

  • a/d/s/ PH30.2 - page 23

    warranty information LIMITED TWO YEAR CONSUMER W ARRANTY Directed Electr onics, Inc. promises to the original pur chaser , to replace this pr oduct should it prove to be defective in workmanship or material under normal use, for a period of two years from the date of purchase by the dealer as indicated by the date code marking of the pr oduct PROVI ...

  • a/d/s/ PH30.2 - page 24

    a Directed Electronics, Inc. All rights reserved G49200 09-02 front_cover.qxd 10/26/56 5:13 AM Page 1 ...

Fabricante a/d/s/ Categoría Portable Speaker

Los documentos del dispositivo a/d/s/ PH30.2 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos a/d/s/
- manuales de instrucciones PH30.2
- hojas de producto a/d/s/
- folletos informativos
- o etiquetas energéticas a/d/s/ PH30.2
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones a/d/s/ PH30.2.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje a/d/s/ PH30.2, instrucciones de servicio, instrucciones cortas o instrucciones de usuario a/d/s/ PH30.2. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto a/d/s/ PH30.2.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo a/d/s/ PH30.2, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar a/d/s/ PH30.2. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de a/d/s/ PH30.2.

El manual de instrucciones completo de a/d/s/ debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual a/d/s/ PH30.2 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice a/d/s/ PH30.2, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de a/d/s/ PH30.2 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo a/d/s/ PH30.2 - que deben facilitarnos los primeros pasos durante el uso de a/d/s/ PH30.2
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con a/d/s/ PH30.2
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de a/d/s/ PH30.2 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de a/d/s/ PH30.2?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con a/d/s/ PH30.2, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con a/d/s/ PH30.2 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)