Español dropdown-ico

Manual de instrucciones Patton electronic Network Hardware

21 de páginas 0.45 mb
Descargar

Pasar a la página of 21

Summary
  • Patton electronic Network Hardware - page 1

    USER MANU AL MODEL 2715 NetLink-E1: E1/Fractional E1 NTU SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .patton.com Part# 07M2715-UM Doc# 08605U2-001, Rev . C Revised 10/26/06 CERTIFIED An ISO-9001 Certified Company ...

  • Patton electronic Network Hardware - page 2

    P A TTON MODEL 2715 T ABLE OF CONTENTS Section Page 1.0 General Information ...............................................................2 1.1 W arranty Statement 1.2 Radio and TV Interference 1.3 CE and T elecommunication Approvals 1.4 Service Information 2.0 General Information ........................................................5 2.1 Featu ...

  • Patton electronic Network Hardware - page 3

    1.4 SERVICE INFORMA TION All warranty and non-warranty repairs must be returned freight prepaid and insured to Patton Electronics. All returns must have a Return Materials Authorization number on the outside of the shipping container . This number may be obtained from Patton Electronics T echnical Support at: tel: (301) 975-1007 ; email: support@pa ...

  • Patton electronic Network Hardware - page 4

    2.0 GENERAL INFORMA TION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for One Y ear parts and labor . If any questions arise during installation or use of the unit, contact Patton Electronics T echnical Services at (301) 975-1007. 2.1 FEA TURES • T erminates ...

  • Patton electronic Network Hardware - page 5

    Switch SW1: Line Coding Use Switch SW1 to control the Network Line Coding options. Set these options to be the same as the Line Coding given to you by your Service Provider . If you are using two Model 2715s together as short range modems, set both units to HDB3. SW4 Line Framing & Coding Off HDB3 On AMI Line Coding Options: High Density Bipola ...

  • Patton electronic Network Hardware - page 6

    Switch SW2: CAS Multiframe The Channel Associated Signaling (CAS) multiframe uses T imeslot 16 (TS16) to send multiframe (MF) alignment data. In CAS MF , a multi- frame is defined as 16 frames, where a frame consists of 32 64kb/s timeslots, numbered 0 to 31. TS16 of the first frame in the MF contains the CAS MF alignment word in the upper four bits ...

  • Patton electronic Network Hardware - page 7

    NOTE: When the data rate is set to 2.048Mb/s, then the unit is forced into G.703 mode, and it transmits user data on all 32 timeslots. There is no framing information; therefore, the CAS MF (SW2)and CRC-4 (SW3) switches are ignored. In all other rate settings, the unit employs G.704 framing; TS0 is reserved for signaling. 3.2 SOFTW ARE CONFIGURA TI ...

  • Patton electronic Network Hardware - page 8

    3.2.1 Introduction to Main Menu After entering the password, you may access all of the system’s functions and parameters. The Main Menu looks like this: HELPFUL HINTS 1. T o make a selection, key the highlighted letter that corre- sponds to a menu selection. 2. T o execute the selection, type [Enter/CR]. 3. T o toggle between options on a highlig ...

  • Patton electronic Network Hardware - page 9

    3.2.2 System Configuration The System Configuration menu looks like this: The System Configuration options are described below: Line Format: G.703 (default) Options: G.703, G.704 G.703: G.703 is unframed, 2.048Mb/s. In this case, the DTE rate is equal to the line rate at the network interface (NI). CAS MF and CRC-4 are disabled. G.704: G.704 reserv ...

  • Patton electronic Network Hardware - page 10

    Clocking : Network (default) Options: Network, Internal, External Network: This is the most commonly used setting when connect- ing to a carrier ’s network. In this mode, the unit recovers the clock from the received signal and uses it to transmit data. In this way the unit remains synchronized to a master clock. In campus applications, one of th ...

  • Patton electronic Network Hardware - page 11

    3.2.3 System Diagnostics The System Diagnostics/Statistics screen looks like this: NOTE: This screen is updated once per second. The System Diagnostics/Statistics options and functions are described below . Local Loop Idle (default) The Local Loop is a bi-lateral loopback in which the data from the local DTE and the data from the remote unit are lo ...

  • Patton electronic Network Hardware - page 12

    22 21 Remote Loop Idle (default) The Remote Digital Loopback (RDL) test checks the performance of both the local and remote Model 2715s, as well as the communica- tion link between them. Data from the local DTE is sent across the entire communication circuit and looped back to the local DTE. The Model 2715 Initiating a RL can be in one of the follo ...

  • Patton electronic Network Hardware - page 13

    23 24 Use this option to select the test pattern used to test the link. NI ST A TUS The Network interface (NI) status is shown in the middle of the Diagnostics/Statistics screen. The brackets are empty when the link is operating normally . Only one error message is provided Receiver Carrier Loss [RCL] occurs when 255 consecutive zeros have been det ...

  • Patton electronic Network Hardware - page 14

    25 26 Loop Timeout The Loop T imeout setting can be set to one of the following: 00:05 = five minutes 00:10 = ten minutes 00:15 = fifteen minutes 00:30 = thirty minutes (default setting) 00:45 = forty-five minutes 01:00 = one hour 01:30 = 90 minutes 02:00 = two hours 03:00 = three hours NEVER = forever—the unit will remain in loopback without use ...

  • Patton electronic Network Hardware - page 15

    27 28 4.3 POWER CONNECTION The Model 2715 offers three ways to supply external power: AC power , DC power and interface power . 4.3.1 Using the AC Power Supply (100-240V AC) The Model 2715 uses a 5VDC, 2A universal input 100-240V AC, power supply (center pin is +5V). The universal input power supply is equipped with a male IEC-320 power entry conne ...

  • Patton electronic Network Hardware - page 16

    29 30 LOS The Loss of Sync LED lights when the unit loses synchronization with the incoming sig- nal. This may happen when there is a fram- ing mismatch or a loss of signal. In unframed mode, the LOS LED monitors the status of the transmit clock. ALM The alarm LED indicates the presence of a AIS or RAI, or Out of Frame condition. The ALM LED will b ...

  • Patton electronic Network Hardware - page 17

    31 32 T o perform an RDL test, follow these steps: 1. Activate RDL. This may be done in two ways: a. Enter Remote Loop from the System Diagnostics/Statistics menu and toggle the <Spacebar> until “TM” appears next to the Remote Loop option.; b. Activate the “RL” signal on the DTE. If you are not sure which lead is the “RL” signal, ...

  • Patton electronic Network Hardware - page 18

    33 34 APPENDIX A P A TTON MODEL 2715 SPECIFICA TIONS Network Data Rate: 2.048 Mbps Network Connector: RJ-48C Nominal Impedance: 120 ohm (75 ohm available when using Patton Model 460 Balun) DTE Interface: V .35 (DCE Orientation) on Male M/34 Line Coding: Selectable AMI or HDB3 Line Framing: G.703 (Unframed) or G.704/G.732 (Framed) CAS Multiframing: ...

  • Patton electronic Network Hardware - page 19

    35 36 APPENDIX C P A TTON MODEL 2715 F ACTOR Y REPLACEMENT P ARTS AND ACCESSORIES Patton Model # Description 2715/CM/UI .....................V .35 to E1 Converter (V .35 M/34 Male, UI) 10 - 09F ...........................6 Foot Control Port Cable, 25 mm to DB9F 08055DCUI......................Universal Input Power Supply 10-CISCO-V35FT -1 .........C ...

  • Patton electronic Network Hardware - page 20

    37 38 APPENDIX D (continued) P A TTON MODEL 2715 INTERF ACE PIN ASSIGNMENTS M/34 Connector , T erminal Interface Pin # Signal A GND (Earth Ground/Shield) B SGND (Signal Ground) D CTS (DCE Source) E DSR (DCE Source, Always On) F CD (DCE Source) L LL (Local Loop, DTE Source) M TM (T est Mode Indicator (DCE Source) N RL (Remote Loop, DTE Source) P TD ...

  • Patton electronic Network Hardware - page 21

    Copyright © 2006 Patton Electronics Company All Rights Reserved. ...

Fabricante Patton electronic Categoría Network Hardware

Los documentos del dispositivo Patton electronic Network Hardware que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Patton electronic
- manuales de instrucciones Network Hardware
- hojas de producto Patton electronic
- folletos informativos
- o etiquetas energéticas Patton electronic Network Hardware
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Patton electronic Network Hardware.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Patton electronic Network Hardware, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Patton electronic Network Hardware. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Patton electronic Network Hardware.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Patton electronic Network Hardware, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Patton electronic Network Hardware. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Patton electronic Network Hardware.

El manual de instrucciones completo de Patton electronic debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Patton electronic Network Hardware - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Patton electronic Network Hardware, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Patton electronic Network Hardware que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Patton electronic Network Hardware - que deben facilitarnos los primeros pasos durante el uso de Patton electronic Network Hardware
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Patton electronic Network Hardware
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Patton electronic Network Hardware en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Patton electronic Network Hardware?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Patton electronic Network Hardware, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Patton electronic Network Hardware probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)