-
Kenmore 141.229952 - page 1
Owner's Manual Liquid Propane Patio Heater Model141.229952 //_ WARNING: Read this Owner's Manual carefully and be sure your patio heater is properly assembled, installed and maintained. Failure to followthese instructions could result in serious bodily injury and/or property damage. This patio heater is intended for outdoor use only and i ...
-
Kenmore 141.229952 - page 2
Warranty ..................................................... 2 Safety Instructions .................................... 2 Clearance Requirements .......................... 5 Parts Diagram and Part Lists ............. 6 Assembly Instructions .............................. 10 Lighting Instructions .................................. 13 Frequently As ...
-
Kenmore 141.229952 - page 3
3. Proper clearance from combustible materials mustbe maintained at all times. Minimum clearances are as follows: Sides 24" Top 18" Below Reflector Head 85" Combustible materials include wood, compressed paper, plant fibers, plastic, plexiglas or other materials capable of being ignited and burned. Such materials shall be considered ...
-
Kenmore 141.229952 - page 4
8. Installation and use of this patioheatermust conform with local codesor, in the absence of local codes, with the Standards of Storage and Handling of Liquefied Petroleum Gases, ANSI/ NFPA58. 9. This patio heateris designed to operate with a standard 20 lb. Liquid Propane Gas (LP gas) tank with Type 1 Tank Connection Device as shown in Fig. 2. (A ...
-
Kenmore 141.229952 - page 5
Kenmore LPG Patio Heater For Outdoor Use Only E 0 CO • _" 0 I CO _'= = E E _0 = 0'3 O_ ! Minimum Clearance from Combustibles 32"(812 mm) Dia. S i2d4_ ( 61_am nmc)e _ E E CO (D CO_ O000HO O0000gO DDODDOOD OOOOOOOO OOOOOOOO O00000OO OOOO00O OOOOOOO OOO00O O000OO 000000 OOOOO OOOOO O00OO O0 O0 , J -7 i-- --i 21"(529 ram) ...
-
Kenmore 141.229952 - page 6
Quantity and Actual Size of Each Hardware Piece: 3/8"x1-1/4" Hex Head Screw Qty. 3 Part # PH001 (attached to the Weighted Base) 3/16"xl/2" Phillips Head Screw Qty. 1 Part # PH005 3/8" Spring Washer Qty. 15 Part # PH002 3/16" Spring Washer Qty. 1 Part # PH006 3/8"x3/4" Hex Head Screw Qty. 6 Part # PH003 3/16&q ...
-
Kenmore 141.229952 - page 7
The following table illustrates a breakdown of the hardware pack. It highlights what components are used in the various stages of assembly. Ref. Component Qty. to Use PH002 PH003 PH002 PH004 P7079A PH003 PH002 PH004 PH016 PH016 PH009 PH010 P7083A P7080A PH005 PH006 PH007 3/8" Spring Washer 3 3/8"x3/4" Hex Head Screw 5 3/8" Sprin ...
-
Kenmore 141.229952 - page 8
Remove all components from the packing carton and place within easy reach. Inspect patio heater parts for damage as you proceed. Do not assemble or operate your patio heater if parts appear damaged. 4 _ D q J D j4 5 J J Note: Thispatio heater Head Assembly is pre-assembled foryour convenience. 14 13 11 ...
-
Kenmore 141.229952 - page 9
REF# DESCRIPTION PART# QTY 1. Aluminum Reflector P7055A 1 2. Heater Head Assembly P7086A 1 3. Rubber Rim P7073A 1 4. LP Gas Tank Cover P7074A 1 5. Upper Post P7075A 1 6. Stainless Steel Fuel Hose P7076A 1 7. Lower Post P7077A 1 8. Leg P7078A 3 9. Hose Holder A P7079A 1 10. Hose Holder B P7080A 1 11. Gas Regulator Assembly P7081A 1 12. Chain Hook wi ...
-
Kenmore 141.229952 - page 10
Before assembling the patioheater, use the parts list to check that all necessary partshave been included. Inspect patio heater for damage as you proceed. Do not assemble or operate the patio heaterif it appears damaged. If you have ques- tions during the assembly process, call 1-888-317- 7642,8am - 8pm CST, Monday throughFriday. CAUTION: While it ...
-
Kenmore 141.229952 - page 11
7. Attachthe Reflector onto Emitter Grid by using 4 of the 1/4" Spring Washers and 1/4" Wing Nuts provided. See Fig. 4. 8. Slide the Tank Cover through the Lower Post and onto the Weighted Base. See Fig. 5. 9. Lift the assembled Upper Post and insert the balance of the Fuel Hose through Lower Post. 10. Keep the Upper Post slightly lifted ...
-
Kenmore 141.229952 - page 12
Ignitor Battery Installation - See Fig. 6 1. Unscrew the Ignitor Cap located on the Heater Head Assembly and remove the Con- tact and Spring from the Ignitor Slot. 2. Place the supplied AA battery into the Ignitor Slot with the positive pole facing outward. See Fig. 6. C_-r,uure 6 HEATER HEAD ASSEMBLY 1 5 V BATTERY (AA size) IcGANpI T O'_.. __ ...
-
Kenmore 141.229952 - page 13
7. Release the Control Knoband turn to "ON". Nevertest for leaks with a flame. Priorto first use, at the beginning of eachseason, or every time your LP gas tank is changed, you must check for gas leaks. Follow these four steps: 1. Make a soap solution by mixing one part liquiddetergent and one part water. . 3. Turn the Control Knob to the ...
-
Kenmore 141.229952 - page 14
Question: Who do t call with questions about my Kenmore Patio Heater assembly or if parts are damaged or missing from my shipping box? Answer: Call the Customer Service Helpline 8am - 8pm CST, Monday through Friday, at 1-888-317-7642. Question: Can I convert my Kenmore Patio Heater from LP gas to natural gas? Answer: No, this patio heater is manufa ...
-
Kenmore 141.229952 - page 15
Your Home FO_ repair- in your home- of all major brand appliances _awn and garden equipment,, or heating and cool ng systems no matter who made it, no matter who sold it! For _e rep acement parts a_ssories and owners manuals that you need to dooitoyourself For Sears professional insta#atio_ of home appliances and items _ike garage door openers and ...
¿Tienes una pregunta acerca de Kenmore 141.229952?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Kenmore 141.229952, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Kenmore 141.229952 probablemente compartirá una forma de solucionarlo.