-
Honeywell CT3400 - page 1
Weekday/Saturday/Sunday Programmable Heat and/or Cool Low Voltage (20 to 30 Vac)Thermostat and Wallplate Model CT3400/CT3455 PR OGRAMMABLE THERMOST A T Honeywell/34 PROGRAMMING AND INSTALLATION INSTRUCTIONS J.S. Rev. 4-97 ©Honeywell Inc. 1997 Printed in U.S.A. Form Number 69-0733—3 69-0733-3 30% 28% 26% 24% 22% 20% 18% 16% 14% 12% 8% 6% 2% 10% 4 ...
-
Honeywell CT3400 - page 2
TOTAL COMFORT TEMPERATURE MANAGEMENT WITH ADAPTIVE INTELLIGENT RECOVERY™ Congratulations! You made a smart choice when you purchased your new Honeywell Thermostat. It’s the smart thermostat that: ■ Keeps you comfortable by automatically calculating exactly when the furnace or air condi- tioning should go on to have the house at the desired co ...
-
Honeywell CT3400 - page 3
STEP 1 Prepare For Installation ■ ■ Check Table 1 to make sure this thermostat is compatible with your system. If not, return to retailer. For more information, call Honeywell Customer Assistance, toll-free 1-800-468-1502. Table 1. Compatibility Chart. System Type Compatible with CT3400/3455 Gas—Standing Pilot Yes Gas—Electronic Ignition Ye ...
-
Honeywell CT3400 - page 4
3 69-0733—3 ■ ■ Acquire tools and items as needed (below). CROSS-RECESSED SCREWDRIVER HAND OR POWER DRILL WITH 3/16 INCH DRILL BIT, IF NEEDED, TO DRILL HOLES IN WALL WIRE CUTTER/STRIPPER OR SHARP KNIFE, IF NEEDED, TO STRIP WIRES MASKING TAPE, IF NEEDED, TO LABEL WIRES AS DISCONNECTED FROM OLD THERMOSTAT LEVEL, IF NEE ...
-
Honeywell CT3400 - page 5
5 69-0733—3 which programmable thermostats will work with your system, call Honeywell Customer Assis- tance at 1-800-468-1502. Three thermostat wires? If you have three wires for heating only and can operate the fan using the fan ON switch, this thermostat will work with your system. However, some hot water (zoned) heating systems have three ther ...
-
Honeywell CT3400 - page 6
7 69-0733—3 IMPORTANT: Although the thermostat has a low battery indicator, replace the batteries once a year to prevent leakage and to prevent the thermostat and heating/cooling system from shutting down due to lack of battery power. As a precaution when leaving home for longer than a month, change batteries before you leave to prevent system fr ...
-
Honeywell CT3400 - page 7
STEP 4 Pr ogram The Thermostat work or school. (This will be a higher tem- perature during heating season, or a lower temperature during cooling season.) DAYTIME is the time period you can set for an energy-saving temperature while you are away at work or school. (This will be a lower temperature during heating season, or a higher temperature durin ...
-
Honeywell CT3400 - page 8
Sunday Program START HEATING COOLING PERIOD TIME TEMPERATURE TEMPERATURE MORNING _____________________ _____________________ _____________________ DAYTIME ______________ ______________ _____________ EVENING ______________ ______________ _____________ NIGHT _____________________ _____________________ _____________________ The temperatures cannot be ...
-
Honeywell CT3400 - page 9
COOLING PROGRAM The times you set for heating remain the same for cooling; you only need to program the temperatures. With system switch at COOL, press and release . Use a to program Mon-Fri MORNING temperature. Repeat using DAYTIME, EVENING, NIGHT keys. For Saturday, press to SAT. Press and release ; use a to program Saturday morning temperature. ...
-
Honeywell CT3400 - page 10
For operating or making changes, use this guide. Temporarily Change temperature for current period only — ; TEMPORARY indicator shows on display, and cancel s itself at next scheduled change. To cancel sooner, you may press . Hold a temperature indefinitely (such as on vacation)— , Hold appears on display; to cancel, press . Check current tempe ...
-
Honeywell CT3400 - page 11
17 69-0733—3 ■ ■ Remove wallplate from wall, and drill 3/16 inch holes in wall (if drywall) as marked. For firmer material such as plaster or wood, drill 7/32 inch holes. Gently tap anchors (provided) into drilled holes until flush with the wall. ■ ■ Reposition wallplate over holes, pulling wires through wiring opening. Loosely insert two ...
-
Honeywell CT3400 - page 12
19 69-0733—3 SYSTEM GRAVITY AIR/WATER HOT WATER OR HIGH EFFICIENCY (90%+AFUE) GAS/OIL WARM AIR ELECTRIC WARM AIR 1A OUT 1 TURN OUT 1 TURN OUT 1 TURN 1B IN (FACTORY SETTING) IN IN DISPLAY 2A 2B 12 hr./ °F OUT 24 hr./ °F (FACTORY SETTING) IN M 618A 1A 1B 2A 2B OUT OUT OUT IN IN IN 24 hr./ °C 12 hr./ °C OUT 1 TU ...
-
Honeywell CT3400 - page 13
21 69-0733—3 NOTE: All wiring must comply with local codes and ordinances. If unsure about household wiring procedures, call your local heating/air conditioning contractor. Refer to masking tape labels you placed on wires when you removed your old thermostat. ■ ■ Match the letter of your old thermostat wire with the terminal of the correspond ...
-
Honeywell CT3400 - page 14
INSTALLATION 24 69-0733—3 23 69-0733—3 STEP 9 Mount The Thermostat A. ENGAGE TABS BETWEEN TOP OF THERMOSTAT AND WALLPLATE MON HEAT ON DAYTIME AM B. PRESS LOWER EDGE OF CASE TO LATCH MON HEAT ON DAYTIME AM Time Temp Current Setting Set Present Day Time Hold Temp Run Program Day Morning Night Daytime Evening Fan On A ...
-
Honeywell CT3400 - page 15
25 69-0733—3 26 69-0733-3 STEP 10 Check Thermostat Operation After Pr ogramming And Installing HEATING Do not check heating system operation by jumpering thermostat terminals at the primary control, such as the gas valve, zone valve, oil burner control. This will damage the thermostat. In- stead, you could jumper R and W wires at the thermostat. ...
-
Honeywell CT3400 - page 16
27 69-0733—3 28 69-0733—3 Move the system switch to OFF and the fan switch to ON. The fan should run continuously. When the fan switch is in the AUTO position, fan cycles with the heating or cooling system. FAN AUTO ON HEAT O FF COOL STEP 11 Set The F an And System Switches First set the fan switch. FAN ON: The fan runs continuously. Use for im ...
-
Honeywell CT3400 - page 17
29 69-0733—3 T r oubleshooting Guide IF… THEN… Display does not come on. ■ Set the system switch to OFF. Remove batteries. Insert back- ward for at least five seconds to reset thermostat. Replace batteries correctly. Display should come on. ■ Make sure batteries are fresh and installed correctly. ■ Gently clean battery contacts using a ...
-
Honeywell CT3400 - page 18
31 69-0733—3 Heating does not come on. ■ Check that switch on thermostat is set to HEAT. ■ Check the system fuse or circuit breaker and replace or reset if necessary. If display is blank or displays REPL BAT, install fresh batteries. ■ Check for correct wiring and good connections. ■ Jumper wires R and W. If heat does not come on, contact ...
-
Honeywell CT3400 - page 19
Adaptive Intelligent Recovery™ ....................... 7,8 Batteries, installation .............. 6 Batteries, replacement ........ 6,7 Blinking display ....................... 6 Canceling programs ............. 15 Change temperature ............. 1 5 Checking current setting ....... 15 Clock display ........................ 19 Conventional Recov ...
-
Honeywell CT3400 - page 20
35 69-0733—3 Limited One-Y ear W arranty Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If, at any time during the warranty period, the product is defective or malfunctions, Honeywell ...
¿Tienes una pregunta acerca de Honeywell CT3400?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Honeywell CT3400, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Honeywell CT3400 probablemente compartirá una forma de solucionarlo.