-
Bunn CEZF - page 1
BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 FAX: (217) 529-6644 www .bunnomatic.com OPER A T IN G & SE R VICE MANUA L CEZ, C E Z F , CDBC , C D B C F A i rp ot , Therm a l C a r afe & Ther m al Se r ver Brew e r s 29253.0000F 02/04 ©1999 Bunn-O-Matic Corporation BUNN BUNN DIS CO N ...
-
Bunn CEZF - page 2
Page 2 INTRODUCTION This equipment will automatically brew a half-gallon batch of coffee into an awaiting server at the press of a button. A hot water faucet may be included for allied beverage use. Most functions of the brewer are digitally controlled. It is only for indoor use on a sturdy counter or shelf. CONTENTS Introduction & W arranty .. ...
-
Bunn CEZF - page 3
Page 3 USER NOTICES Carefully read and follow all notices in this manual and on the equipment. All labels on the equipment should be kept in good condition. Replace any unreadable or damaged labels. # 00986.0000 # 00656.0000 # 00658.0000 # 10044.0000 29253 011900 ...
-
Bunn CEZF - page 4
Page 4 ELECTRICAL REQUIREMENTS CAUTION - The brewer must be disconnected from the power source until specified in Initial Set-Up. Model 15 has an attached cordset and requires 2-wire grounded service rated 120 volts ac, 15 amp, single phase, 60 Hz. Model 35 requires 3-wire, grounded service rated 120/208 or 120/240 volts ac, 20 amp, single phase, 6 ...
-
Bunn CEZF - page 5
Page 5 OPERA TING CONTROLS Model CEZ-APS/TS/TSR ON/OFF SWITCH Placing the "ON/OFF" switch in the "ON" upper position enables the brew circuit, and energizes the tank refill circuit. Placing the switch in the "OFF" lower position stops tank refilling and brewing. Stop- ping a brew cycle after it has been started will no ...
-
Bunn CEZF - page 6
Page 6 INITIAL SET -UP 1. Insert an empty funnel into the funnel rails. 2. Place an empty server under the funnel. 3. Connect the brewer to the power source. 4. Model CDBC-APS/TC/TS/TSR – Press the "ON/OFF" switch (indicator glowing). Model CEZ-APS/TS/TSR – Place the "ON/OFF" switch in the "ON" upper position. 5. W ...
-
Bunn CEZF - page 7
Page 7 CEZ-APS/TS/TSR ADJUSTMENTS & OPTIONAL SETTINGS IMPORT ANT : The tank must be full and fill so- lenoid shut off prior to making these adjust- ments. Adjusting Brew Volumes The brewer is factory set to deliver 64 ounces ± 2 for each brew cycle. BREW VOLUME SET-UP: Use the following steps when the setting is unknown or a different circuit ...
-
Bunn CEZF - page 8
Page 8 CDBC-APS/TC/TS/TSR ADJUSTMENTS & OPTIONAL SETTINGS Setting Brew Temperature The brewer is factory set to brew at 200 ° F(95 ° C). To change this setting, press and hold the "HIDDEN" switch beneath the "®". The word "TEMP" above the "ON/OFF" switch will glow to correspond with the temporary funct ...
-
Bunn CEZF - page 9
Page 9 CDBC-APS/TC/TS/TSR ADJUSTMENTS & OPTIONAL SETTINGS (cont) W ater Sensing Threshold Adjustment Procedure 1. Make sure the tank is full of water to be used for calibration. The water must be in contact with the refill probe. 2. Unplug the brewer from the power source, then press and hold the BREW button while power is reapplied. 3. Continu ...
-
Bunn CEZF - page 10
Page 10 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic Technical Service Department. • Inspection, testing, and repair of electrical equipment should be performed only b ...
-
Bunn CEZF - page 11
Page 11 Will not fill or refill Fill or refill does not shut "OFF" (ON/OFF Switch "ON") PROBABLE CAUSE REMEDY PROBLEM 1. Power off to brewer (CDBC-APS/ TC/TS/TSR & CEZ-APS/TS/TSR) 2. Water shut off (CDBC-APS/TC/ TS/TSR & CEZ-APS/TS/TSR) 3. Display flashing (CDBC-APS/TC/ TS/TSR) or ready light flashing (CEZ-APS/TS/TSR) 4. ...
-
Bunn CEZF - page 12
Page 12 TROUBLESHOOTING (cont.) Fill or refill does not shut "OFF" (ON/ OFF Switch "ON") (cont) Fill or refill does not shut "OFF" (ON/ OFF Switch "OFF") PROBABLE CAUSE REMEDY PROBLEM 2a. Water Level Probe Sensing System (CDBC-APS/TS/TSR) 2b. Water Level Probe Sensing Sys- tem (CEZ-APS/TC/TS/TSR) 3. Refill va ...
-
Bunn CEZF - page 13
Page 13 TROUBLESHOOTING (cont.) PROBLEM PROBABLE CAUSE REMEDY HEATING CIRCUIT 1. Display flashing (CDBC-APS/TC/ TS/TSR) or ready light flashing (CEZ-APS/TS/TSR) 2. Water not touching temperature probe 3a. Dry Plug In Probe Sensing Sys- tem (CDBC-APS/TC/TS/TSR) 3b. Dry Plug In Probe Sensing Sys- tem (CEZ-APS/TS/TSR) Brewer has shut down due to malfu ...
-
Bunn CEZF - page 14
Page 14 TROUBLESHOOTING (cont.) PROBLEM PROBABLE CAUSE REMEDY Water does not heat to proper temperature (cont.) IMPORTANT: Make sure no tem- perature tests are taken before the ready light is "ON". Tank tempera- ture must be stabilized before read- ings are taken. Spitting or excessive steaming 4a. Temperature Probe (CDBC-APS/ TC/TS/TSR) ...
-
Bunn CEZF - page 15
Page 15 TROUBLESHOOTING (cont.) PROBLEM PROBABLE CAUSE REMEDY Spitting or excessive steaming (cont.) Brewer is making unusual noises 2a. Temperature Probe (CDBC-APS/ TC/TS/TSR) 2b. Temperature Probe (CEZ-APS/ TS/TSR) 3. Control Board (CDBC & CEZ) 1. Plumbing lines 2. Water supply 3. Lime build up A) Remove the probe from the grom- met and subme ...
-
Bunn CEZF - page 16
Page 16 TROUBLESHOOTING (cont.) PROBLEM PROBABLE CAUSE REMEDY BREWING CIRCUIT Brew cycle will not start 1. Display flashing (CDBC-APS/TC/ TS/TSR) or ready light flashing (CEZ-APS/TS/TSR) 2. No water 3. No power or incorrect voltage to the brewer 4. ON/OFF switch not in the "ON" position 5. Low water temperature (Brew lockout is enabled) 6 ...
-
Bunn CEZF - page 17
Page 17 TROUBLESHOOTING (cont.) PROBLEM PROBABLE CAUSE REMEDY BREWING CIRCUIT (cont.) If the start switch (CEZ-APS/TS/ TSR) or switch panel (CDBC-APS/ TC/TS/TSR) is operating properly, proceed as follows. Attach a volt- meter to the terminals of the dis- pense valve solenoid. Connect the brewer to the power source. Turn on the brewer and press the ...
-
Bunn CEZF - page 18
Page 18 TROUBLESHOOTING (cont.) PROBLEM PROBABLE CAUSE REMEDY BREWING CIRCUIT (cont.) Dripping from sprayhead Weak beverage 1. Lime build up 2. Dispense valve 1. Sprayhead 2. Water temperature 3. Filter type 4. Coffee grind 5. Funnel loading Inspect the tank assembly for ex- cessive lime deposits. Delime as required. Remove the dispense valve and c ...
-
Bunn CEZF - page 19
Page 19 TROUBLESHOOTING (cont.) PROBLEM PROBABLE CAUSE REMEDY BREWING CIRCUIT (cont.) Dry coffee grounds remain in the funnel 1. Sprayhead 2. Funnel loading Make sure sprayhead is present and holes are clear and unobstructed. There should be separate streams of water coming out of each hole in the sprayhead. The BUNN ® paper filter must be centere ...
-
Bunn CEZF - page 20
Page 20 DIAGNOSTICS Intermittent flashing of the READY indicator (Model CEZ) or the bank of temperature indicators (Model CDBC) indicates that a fault exists. Count the number of flashes between pauses and use this chart as a guide to investigating the fault. FLASHES CAUSE THINGS TO CHECK 1 Dry Plug - In Fault - Water Pressure Sheath of temperature ...
-
Bunn CEZF - page 21
Page 21 BUNN M AN UFA CTU RE D B Y BU NN-O -M AT IC C OR POR ATIO N SPR INGF IE LD, I LLINO IS , U.S .A . M OD EL S/ N V OLTS A .C. AMP W AT TS PH ASE W IRE HE RTZ COV ERE D UN DER O NE O R MORE OF TH E FO L LO W ING PA TENT S : ON E OR M ORE OTH ER P ATE NTS M AY B E PE NDI NG D IS C O N N E C T F R O M P O W E R S O U R C E B EF O R E R E M O V A ...
-
Bunn CEZF - page 22
Page 22 BUNN M A N U F A C T U R E D B Y B U N N - O - M A T I C C O R P O R A T I O N S P R IN G F I E L D , I L L IN O IS , U . S . A . M O D E L S / N V O L T S A . C . A M P W A T T S P H A S E W I R E H E R T Z C O V E R E D U N D E R O N E O R M O R E O F T H E F O L L O W IN G P A T E N T S : O N E O R M O R E O T H E R P A T E N T S M A Y B ...
-
Bunn CEZF - page 23
Page 23 TRM2 J1 J2 J3 J4 J5 J6 J7 T RM1 CAUTION : WARMERS AND SURFACES ARE HOT SERVICE (cont.) CONTROL BOARD - Model CEZ-APS/TS/TSR Location: The Control Board is located inside the trunk behind the front access panel. Test Procedures: The test procedures for the control board will vary depending upon the problems experienced by the brewer. Refer t ...
-
Bunn CEZF - page 24
Page 24 BUNN MANUFACTURED BY BUNN-O-MATIC CORPORATION SPRINGFIELD, ILL INOIS, U.S .A. MODEL S/N VOLTS A.C. AMP W ATTS PHAS E W IRE HERT Z COVERED UNDER ONE OR MOREOF THE FOLL OWING PATENTS : ONE OR MORE OT HER P ATE NTS MAY BE PENDING SERVICE (cont.) SWITCH PANEL - Model CDBC-APS/TC/TS/TSR Location: The Switch Panel is located in the front of the h ...
-
Bunn CEZF - page 25
Page 25 BUNN MANUFACTURED BY BUNN-O-MATIC CORPORATION SPRINGFIELD, ILLINOIS, U.S.A. MODEL S/N VOLTS A.C. AMP WATTS PHASE WIRE HERTZ COVERED UNDE R ONE OR MOREOF THE FOLLOWING PATENTS : ONE OR M ORE OTHER PATENTS MAY BE PENDING DISCONNECT FROM POWER SOURCE BEFORE REMOVAL OF ANY PANEL OR REPLACEMENT OF ANY COMPONENT! WARNING ! CAUTION : WARMERS AND S ...
-
Bunn CEZF - page 26
Page 26 BUNN MANUFACTURED BY BUNN-O-MATIC CORPORATION SPRINGFIELD, ILLINOIS, U.S.A. MODEL S/N VOLTS A.C. AMP WATTS PHASE WIRE HERTZ COVERED UNDER ONE OR MOREOF THE FOLLOWING PATENTS : ONE OR MORE OTHER PATENTS MAY BE PENDING DISCONNECT FROM POWER SOURCE BEFORE REMOVAL OF ANY PANEL OR REPLACEMENT OF ANY COMPONENT! WARNING ! CAUTION : WARMERS AND SUR ...
-
Bunn CEZF - page 27
Page 27 BUNN M A NU FA CT URE D BY B UNN -O -M AT IC C O R PO R A T ION SP RIN G FIELD , IL L IN OIS , U .S .A. MO DEL S /N V OL T S A.C . AM P WA TT S P HA SE W IR E HE RT Z CO V ERE D U N DE R O NE O R M O R E OF T HE FOL L O WIN G P AT E NT S : ON E O R M O RE O TH ER PAT EN TS M A Y B E PE NDIN G SERVICE (cont.) DISPENSE VALVE Location: The dis ...
-
Bunn CEZF - page 28
Page 28 BUNN M A N U F A C T U R E D B Y B U N N - O - M A T I C C O R P O R A T I O N S P R I N G F I E L D , I L L I N O I S , U . S . A . M O D E L S / N V O L T S A . C . A M P W A T T S P H A S E W I R E H E R T Z C O V E R E D U N D E R O N E O R M O R E O F T H E F O L L O W I N G P A T E N T S : O N E O R M O R E O T H E R P A T E N T S M A ...
-
Bunn CEZF - page 29
Page 29 Location: The tank heater is located inside the tank and secured to the tank bottom. Test Procedures: 1. Disconnect the brewer from the power supply. 2. With a voltmeter, check the voltage across the white or red wire from the terminal block and the black wire from the control board. Connect the brewer to the power source. The indication mu ...
-
Bunn CEZF - page 30
Page 30 P1856 SERVICE (cont.) TANK HEATER (Cont.) BLK to Control Board WHI or RED to Terminal Block FIG. 14 TANK HEATER WIRING 17. Install tank assembly onto mounting brackets and secure in place with four #8-32 nuts. 18. Install tank lid and secure in place with eight #8-32 nuts. 19. Connect the two white wires of the tank warmer blanket. 20. Conn ...
-
Bunn CEZF - page 31
Page 31 T RM 2 J1 J2 J3 J4 J5 J6 J7 TR M1 CAUTION : WARMERS AND SURFACES ARE HOT SERVICE (cont.) REFILL VALVE Location: The refill valve is located inside the trunk on the lower center part of the component bracket. Test Procedures: 1. Disconnect the brewer from the power source. 2. Disconnect the white and white/blue wires from the refill valve. S ...
-
Bunn CEZF - page 32
Page 32 SCHEMA TIC WIRING DIAGRAM CDBC-APS/TS/TSR 29253 111103 EARL Y MODELS SOL 29257.0000B 12/99 ©1998 BUNN-O-MATIC CORPORATION TANK HEATER L1 GRN GRN RED-14 (MODEL 35) WHI-14 (MODELS 15 & 20) N L2 BLU-14 BLU-14 "KEEP WARM" HEATER WHI WHI LIMIT THERMOSTAT WHI WHI WHI WHI SOL REFILL DISPENSE J1-1 J1-2 J1-1 J1-5 J1-10 C O N T R O L P ...
-
Bunn CEZF - page 33
Page 33 SCHEMA TIC WIRING DIAGRAM CEZ-APS/TS/TSR WHI 29341.0000B 6/99 ©1998 BUNN-O-MATIC CORPORATION WHI WHI BREW SWITCH TANK HEATER GRN RED-14 (MODEL 35) WHI-14 (MODELS 15 & 20) N L2 BLU-14 "KEEP WARM" HEATER WHI SOL REFILL SOL DISPENSE TRM-1 TRM-2 J7-1 J7-2 J1-1 J1-8 J5-1 J5-6 C O N T R O L B O A R D COM N.O. BLK BLK-14 BLK-14 BLK ...
-
Bunn CEZF - page 34
Page 34 LA TE MODELS 29253 021604 SOL SCHEMATIC WIRING DIAGRAM CDBC 15, 20 & 35 APS/TC/TS 29257.0001D 02/04 ©1999 BUNN-O-MATIC CORPORATION TANK HEATER L1 GRN RED-14 (MODEL 35) WHI-14 (MODELS 15 & 20) N L2 BLU-14 BLU-14 "KEEP WARM" HEATER WHI LIMIT THERMOSTAT WHI WHI WHI WHI SOL REFILL DISPENSE J1-1 J1-2 J1-1 J1-5 J1-10 C O N T R ...
¿Tienes una pregunta acerca de Bunn CEZF?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Bunn CEZF, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Bunn CEZF probablemente compartirá una forma de solucionarlo.