-
Maytag DC68-02033B-03 - page 1
1 DC68-02033B-03 AUT OMA TIC DR YER INST ALLA TION INSTRUCTIONS MISE EN SER VICE SÉCHEUSE AUT OMA TIQUE INSTRUCCIONES DE INST ALACIÓN DE LA SECADORA AUT OMÁTICA The installation, including a proper exhaust system, is the responsibility of the owner . La responsabilité de la mise en service, y compris le système d'évacuation qui convient, ...
-
Maytag DC68-02033B-03 - page 2
2 Note: The height of the dryer from top to floor is 38" with the leveling leg screwed all the way in. The customer can unscrew the leg out an additional 78" for a total overall height of 38 7/8". • T eflon tape or pipe joint compound (gas only) • Cutting knife • Pipe wrench (gas only) • Nut drivers • Level • Screw drive ...
-
Maytag DC68-02033B-03 - page 3
3 IMPORT ANT T O INST ALLER Please Read The Following Instructions Carefully Before Starting T o Install The Dryer . These Instructions Should Be Retained For Future Reference. REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES SUCH AS DR YERS TO A VOID THE DANGER OF A CHILD SUFFOCA TING. LOCA TION CONSIDERA TIONS The dryer should be located to permit a ...
-
Maytag DC68-02033B-03 - page 4
4 EXHAUSTING Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the room. In the United States: • All dryers must be exhausted to the outside. • Only rigid or flexible metal duct should be used for exhausting. In Canada: • All dryers must be exhausted to the outside. Outside the U.S. and ...
-
Maytag DC68-02033B-03 - page 5
5 • Exhaust systems longer than recommended can extend drying times, affect machine operation and may collect lint. • The exhaust duct should end with an exhaust hood with a swing out damper to prevent back drafts and entry of wildlife. Never use an exhaust hood with a magnetic damper . • The hood should have at least 12 inches (30.5 cm) of c ...
-
Maytag DC68-02033B-03 - page 6
GAS REQUIREMENTS Use only Natural or LP (liquid propane) gases. THE INST ALLA TION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NA TIONAL FUEL GAS CODE ANSI/Z223.1, LA TEST REVISION (FOR THE UNITED ST A T ES), OR WITH THE CAN/CGA-B149 INST ALLA TION CODES (FOR CANADA). Gas dryers are equipped with a burner orifice for o ...
-
Maytag DC68-02033B-03 - page 7
7 GROUNDING This dryer must be grounded. In the event of malfunction or breakdown, the ground will reduce the risk of electrical shock by providing a path of least resistance for electrical current. GAS MODELS This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an approp ...
-
Maytag DC68-02033B-03 - page 8
8 • If a power cord is used, the cord should be plugged into a 30-ampere receptacle. • The power cord is NOT provided with U.S. electric model dryers. IMPORT ANT : When permitted by local codes, the dryer electrical supply may be connected by means of a new power supply cord kit, marked for use with clothes dryer , that is U.L. listed, rated at ...
-
Maytag DC68-02033B-03 - page 9
9 INST ALLA TION Parts and literature are packaged inside of dryer drum. T o Install... 1. Move dryer to an appropriate location for installation. Consider installing the dryer before the washer in side-by-side installations, to allow access to gas, electrical and exhaust connections. Lay two of the carton corner posts on the floor . T ip the dryer ...
-
Maytag DC68-02033B-03 - page 10
10 3-WIRE SYSTEM CONNECTIONS 1. Loosen or remove center terminal block screw . 2. Connect neutral wire (white or center wire) of power supply cord to the center , silver colored terminal screw of the terminal block. T ighten screw . 3. Connect the other wires to outer terminal block screws. T ighten screws. 4. T ighten strain relief screws. 5. Inse ...
-
Maytag DC68-02033B-03 - page 11
11 FINAL INST ALLA TION CHECK LIST ■ Dryer is plugged into electrical outlet and is properly grounded. ■ Exhaust duct work is hooked up and joints taped. ■ Plastic flexible duct is NOT used. ■ Use rigid or stiff walled flexible metal vent material. ■ Dryer is level with all legs firmly on the floor . ■ Gas Models – gas is turned on, t ...
-
Maytag DC68-02033B-03 - page 12
12 ADDITIONAL INSTRUCTIONS FOR EXPORT MODELS (Not U.S. Mexico, or Canada) Contact the distributor that sold the appliance or: Maytag International, 1475 East Woodfield Road Schaumburg, Illinois 60173 Phone: 847-273-3100, for information on product, shipping damage, replacement parts and accessories. Maytag dryer models manufactured for operation on ...
-
Maytag DC68-02033B-03 - page 13
13 1. Disconnect power supply to unit. 2. Remove 2 screws on door hinge. 3. Lift the door and remove from dryer . 4. Remove 2 screws on opposite side of door hinge. 5.Remove 2 screws on holder lever . 6. Locate door at the other side and reassemble door to dryer . 7. Reassemble holder lever . 8. Reassemble 2 screws in remained holes. Door Reversal ...
¿Tienes una pregunta acerca de Maytag DC68-02033B-03?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Maytag DC68-02033B-03, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Maytag DC68-02033B-03 probablemente compartirá una forma de solucionarlo.