-
CDA ECP112 - page 1
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www .cda.eu ECP/ECN Extractors Manual for Installation, Use and Maintenance ...
-
CDA ECP112 - page 2
2 Important The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CD A reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment. This appliance is no ...
-
CDA ECP112 - page 3
3 safety (L VD) and Electromagnetic interference compatibility (EMC). IMPORT ANT INFORMA TION FOR CORRECT DISPOSAL OF THE PRODUCT IN A CCORD ANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer providing appliance recycling services. Disposin ...
-
CDA ECP112 - page 4
4 • This extractor has been designed to be used in a room with a volume of less than 36m. • Steam cleaners must not be used when cleaning this appliance. • The performance of your extractor will vary depending on a number of factors. These include: type of extraction, length of ducting, room volume, ventilation available and cleanliness of ...
-
CDA ECP112 - page 5
5 Using your Extractor For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for appro ximately 15 minutes after the end of cooking. Control Panel A - Power o button B - Speed level buttons C - Light button T o switch the extractor light on or o • Press button “C” . T o switch on ...
-
CDA ECP112 - page 6
6 Care and Maintenance IMPORT ANT : DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRA CT OR WITHOUT FIRST SWIT CHING OFF THE ELECTRICITY SUPPL Y . Cleaning Y ou should use a nonabrasive cleaner . Any abrasive cleaner (including Cif ) will scratch the surface and could erase the control panel markings. Y ou can clean your extractor eectively by ...
-
CDA ECP112 - page 7
7 prevent damage from other items in the dishwasher . T o remove the grease filter , push in the button on the handle and then pull down on the filter at the front as shown in figure 2. When you have released it at the front, then you can pull the filter out completely . After rinsing and drying, reassemble the grease filter to the hood by rev ...
-
CDA ECP112 - page 8
8 Fig. 3 C D Model Lightbulbs required ECP/ECN 12V G4 type Changing the Light IMPORT ANT : DO NO T PERFORM MAINTENANCE OR CLEANING OF THE EXTRA CT OR WITHOUT FIRST SWIT CHING OFF THE ELECTRICITY SUPPL Y . DO NO T CHANGE THE LIGHT BULB IMMEDIA TEL Y AFTER USE AS THE BULB WILL BE HO T . ALL OW IT T O COOL BEFORE REMOVING IT . Carefully prise open the ...
-
CDA ECP112 - page 9
9 Model Lightbulbs required ECP/ECN 12V G4 type Bulb replacement is not covered by the guarantee. Only use bulbs recommended for your extractor . Do not fit bulbs of a higher power rating. Bulbs of a lower power rating may be adequate for use, generally last longer and use less energy . Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED ...
-
CDA ECP112 - page 10
10 correspond with the coloured markings identifying the terminals connecting to the fuse spur , proceed as follows: • The wire which is coloured green and yellow must be connected to the terminal marked E (Earth) or coloured green. • The wire which is coloured blue must be connected to the terminal marked N (Neutral) or coloured black. • The ...
-
CDA ECP112 - page 11
11 Electrical Information Mains electrical voltage: 230 – 240V ac T otal rated power consumption: 140W T roubleshooting Please note: Y our extractor is equipped with a motor protection device that will switch o the motor to prevent damage from overheating. This may happen during cooking when most or all of the zones/burners are being used simu ...
-
CDA ECP112 - page 12
12 Mounting your Extractor When the extractor is to be installed above an electric hob, the minimum distance between the hob and extractor must ex ceed 600mm (650mm is recommended). When the extractor is to be installed above a gas hob, the minimum distance between the hob and extractor must ex ceed 700mm (750mm is recommended). If the instructions ...
-
CDA ECP112 - page 13
13 IN THE ABSENCE OF ANY INSTRUCTIONS SUPPLIED WITH THE GAS HOB, THE MINIMUM DIS T ANCE BETWEEN THE HOB AND EXTRA CT OR MUST BE A T LEAS T 760mm. The width of any hob must not be greater than the width of the extractor installed above it. Installation The metal casing of this appliance has been coated with a preservative to protect it during transp ...
-
CDA ECP112 - page 14
14 Fig. 5 Figu re 2 - M ar k wal l a s r eq ui re d ( s ee ta bl e 1) Fig. 7 Figu re 3 - D ri l l h o l es Fig. 9 Fig. 10 Figu re 5 - Se c ur e hoo d ( t igh t en a ll scr ews) Figu re 6 - Fi t d uc tin g adap t or T ools required Mark wall as required (see table 2) Drill holes Fit wall fixings and top screws - Ensure that any fixings you use are ...
-
CDA ECP112 - page 15
15 Fig. 12 Fig. 13 Fig. 14 Mount upper and lower chimney brackets Fix ducting (seal joint) Figu re 7 - Mo u n t ch im ne y b ra c ke ts Figu re 8 - F i x d uc t ing (s ea l j o in t) Figu re 9 - Mo u nt t h e c h im ne y Figu re 10 - Adj u st an d s e c u re t h e ch im ne y Mount the chimney Adjust and secure the chimney Fig. 11 Figu re 10 - Adj u ...
-
CDA ECP112 - page 16
16 ...
-
CDA ECP112 - page 17
17 ...
-
CDA ECP112 - page 18
18 ...
-
CDA ECP112 - page 19
19 E & O E. All instructions, dimensions and illustrations are provided for guidance only . CDA reserve the right to change specifications without prior notice. Attribute Symbol Units Model Identification ecn62/72/92 ecp62/72/82 ecp92/102/112 Annual Energy Consumption AEC Hood 84.8 84.8 85.1 kWh Time increase factor f 1.7 1.7 1.7 Fluid Dynamic ...
-
CDA ECP112 - page 20
Please contact our Customer Care Department, or for Service on the details below . Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www. cda.eu ...
¿Tienes una pregunta acerca de CDA ECP112?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con CDA ECP112, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con CDA ECP112 probablemente compartirá una forma de solucionarlo.