-
Patton electronic 2168 - page 1
USER MANUAL CopperLink™ Ether net Extenders Model 2158 & 2168 SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P ar t# 07M2158_2168 Rev . A Doc# 058091U Revised 3/24/03 An ISO-9001Cer tified Company e-mail: info@direktronik.se tel: 08-52 400 700 fax: 08-520 18121 ...
-
Patton electronic 2168 - page 2
2 CONTENTS 1.0 Warranty Information ................................................................. 4 1.1 Radio and TV Interference ............................................................ 4 1.2 CE Notice ...................................................................................... 4 1.3 Service ...................................... ...
-
Patton electronic 2168 - page 3
3 D CopperLink Series Interface Pin Assignment ........................ 25 D.1 10/100Base-T Interface .............................................................. 25 RJ-45 .......................................................................................... 25 D.2 CopperLink Interface ......................................................... ...
-
Patton electronic 2168 - page 4
4 1.0 W ARRANTY INFORMATION P atton Electronics warrants all CopperLink Ethernet Extender compo- nents to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of the ship- ment. This warranty is limited to def ects in w orkmanship or mater ials, and does not cov er cust ...
-
Patton electronic 2168 - page 5
5 1.3 SERVICE All warranty and non-w arranty repairs must be returned freight prepaid and insured to P atton Electronics. All returns must hav e a Return Mater i- als A uthorization number on the outside of the shipping container . This number ma y be obtained from Patton Electronics T echnical Services at: • T el: +1 (301) 975-1007 • Email: su ...
-
Patton electronic 2168 - page 6
6 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or one year f or par ts and labor . If any questions or problems arise during installation or use of this product, contact P atton Electronics T echnical Suppor t at +1 (301) 975-1007. ...
-
Patton electronic 2168 - page 7
7 passing pack ets across the CopperLink link that are meant for the remote peered LAN. Figure 1. T ypical application The CopperLink/L modem and CopperLink/R modem work together to create a transparent e xtension between two peered Ethernet LANs. Figure 1 shows a typical point-to-point application. ...
-
Patton electronic 2168 - page 8
8 3.0 INSTALLATION Because the CopperLink Ethernet Extender requires no configuration, it can be installed quickly . If you are installing a standalone unit, ref er to section 3.1 “Standalone unit installation”. Otherwise, refer to section 3.2 “Rack card installation”. Note If asymmetric transmission or line rates other than 12.5 Mbps are ...
-
Patton electronic 2168 - page 9
9 3.2 RACK CARD INSTALLATION The CopperLink Ethernet Extender rack card comprised a front card and a rear card.Do the f ollowing to install the cards into the rac k chassis: 1. Slide the rear card into the back of the chassis along the metal r ails. 2. Secure the rear card using the supplied metal screws . 3. Slide the front card into the chassis u ...
-
Patton electronic 2168 - page 10
10 6. Connect the Ether net interface (ref er to section 3.4, “Connecting the 10/100Base-T Ethernet Interface” on page 11). 3.3 CONNECTING THE T WISTED-PAIR LINE INTERFACE The CopperLink Ethernet Extender suppor ts communication betw een two peer Ethernet LAN sites over a distance of up to 6,000 ft (1.83 km) ov er 24 A WG (0.5 mm) twisted-pair ...
-
Patton electronic 2168 - page 11
11 The terminal bloc k connector on the CopperLink Ethernet Extender's twisted pair interf ace is polarity insensitive and is wired f or a two-wire interf ace. The signal/pin relationships is shown in Figure 5. Figure 5. CopperLink Ethernet Extender twisted pair line interface. 3.4 CONNECTING THE 10/100BASE-T ETHERNET INTERFACE The shielded RJ ...
-
Patton electronic 2168 - page 12
12 Connecting the 10/100Base-T Ethernet P or t to a Hub The CopperLink Ethernet Extender 10/100Base-T interface is configured as DTE (Data T er minal Equipment), just like a 10/100Base-T network interf ace card in a PC . Theref ore, it “expects” to connect to a 10/100Base-T Hub using a straight-through RJ-45 cab le. Figure 7 dia- grams the cab ...
-
Patton electronic 2168 - page 13
13 DC power (supplied via the po wer supply jack to the CopperLink Ether- net Extender) must meet the f ollowing requirements; DC power supplied must be regulated +5VDC ±5%, 1.0A minimum. Center pin is +5V . The barrel type plug has a 2.5/5.5/10mm I.D ./O.D ./Shaft Length dimensions. The CopperLink Ethernet Extender does not have a po wer switch, ...
-
Patton electronic 2168 - page 14
14 4.0 CONFIGURATION (MODEL 2168 ONLY) The CopperLink Ethernet Extender has eight DIP switches f or configur- ing the unit f or a wide variety of applications. This section describes s witch locations and e xplains the different configurations . 4.1 CONFIGURING THE HAR DWARE DIP SWITCHES Using a small flat-tip screwdriv er , remov e the protecti ...
-
Patton electronic 2168 - page 15
15 Figure 10. Model 2168 standalone modem DIP switch orientation Figure 11. Model 2168 rack card DIP s witch orientation ...
-
Patton electronic 2168 - page 16
16 4.2 CONFIGURING DIP SWITCH S1 DIP s witch S1 is where you configure the CopperLink line r ate, symmet- ric or asymmetr ic, Ethernet full auto negotiation capability (100Base-T full or half duple x, 10Base-T full or half duple x) or limited auto sense (only 100Base-T half duple x, 10Base-T full or half duple x). Switch S1-1: Ethernet Auto Sense ...
-
Patton electronic 2168 - page 17
17 T able 3: Asymmetric CopperLink Line Rates Selection Char t S1-2 S1-3 S1-4 Asymmetric Line Rates DS/US OFF OFF ON 4.17 Mbps/1.56 Mbps (Mode 0) OFF ON ON 9.38 Mbps/1.56 Mbps OFF ON OFF 16.67 Mbps/2.34 Mbps T able 4: Reserved for future use S1-5 S1-6 S1-7 S1-8 Reserved for future use OFF OFF OFF OFF Reser ved (F actor y Default) ...
-
Patton electronic 2168 - page 18
18 5.0 OPERATION Once the CopperLink Ethernet Extenders are proper ly installed, they should operate transparently . No user settings required. This section describes reading the LED status monitors. 5.1 POWER UP Bef ore applying power to the CopperLink Ethernet Extender , please re view section 3.5, “Connecting P ower” on page 12 to verify tha ...
-
Patton electronic 2168 - page 19
19 T able 5: F ront panel LED descr iption for standalone modem LED Description Po w e r On (green) when power is applied to the unit. Off when no power is applied to the unit. CopperLink - Link On (green) when the end-to-end CopperLink link between the units is estab lished. Off when the link has not been established or when the link f ails Copper ...
-
Patton electronic 2168 - page 20
20 Figure 13. CopperLink Ether net Extender rack card front panel T able 6: F ront panel LED description for rack card modem LED Description P ower Solid GREEN to indicate the unit is powered on. CopperLink Ethernet Extender Link (Active Green) Solid g reen (ON) to indicate that the end-to-end CopperLink link between the CopperLink Ethernet Extende ...
-
Patton electronic 2168 - page 21
21 APPENDIX A SPECIFICATIONS A.1 LAN CONNECTION • Shielded RJ-45, 10/100Base-T , IEEE 802.3 Ether net • CopperLink Connection: RJ-45 and T er minal Block A.2 T RANSMISSION LINE T wo-wire unconditioned twisted pair. A.3 COPPERLINK LINE RATE Model 2168 —16.67 Mbps, symmetric upstream/downstream. Additional symmetric and asymmetr ic rates are a ...
-
Patton electronic 2168 - page 22
22 A.8 T EMPERATURE RANGE 32–122°F (0–50°C) A.9 HUMIDITY Up to 90% non-condensing. A.10 DIMENSIONS 1.58H x 4.16W x 3.75D in. (10.6H x 4.1W x 8.8D cm) ...
-
Patton electronic 2168 - page 23
23 APPENDIX B MODEL 2158 SERIES F ACTOR Y REPLACEMENT P AR TS AND ACCESSOR IES *Only required with optional UI power supply (08055DCUI) P atton Model # Description Base Models 2158/L Local CopperLink Ethernet Extender, no po wer supply 2158/R Remote CopperLink Ethernet Extender, no po wer supply 2158-2PK CopperLink Ethernet Extender Kit: includes o ...
-
Patton electronic 2168 - page 24
24 APPENDIX C MODEL 2168 SERIES F ACTOR Y REPLACEMENT P AR TS AND ACCESSOR IES *Only required with optional UI power supply (08055DCUI) P atton Model # Description Base Models 2168RC/L Local Multi Rate CopperLink Rack Card 2168RC/R Remote Multi Rate CopperLink Rack Card 2168/L Local Multi Rate CopperLink Ethernet Extender, no po wer supply 2168/R R ...
-
Patton electronic 2168 - page 25
25 APPENDIX D COPPERLINK SERIES INTERFACE PIN ASSIGNMENT D.1 10/100BASE-T INTERFACE RJ-45 • Pin 1: TX+ • Pin 2: TX- • Pin 3: RX+ • Pin 6: RX- • Pins 4, 5, 7, 8: no connection D.2 COPPERLINK INTERFACE RJ-45 • Pin 4: RING • Pin 5: TIP • Pins 1, 2, 3, 6, 7, 8: no connection T erminal Block See Figure 5 on page 11. ...
-
Patton electronic 2168 - page 26
26 APPENDIX E DISTANCE CHAR T, BASED ON 24 A WG (0.5 MM) Note Model 2158 is fixed at 12.5 Mbps , 4,000 ft (1,220 m). Symm Line Rate (DS/US) Distance in feet (km) 6.25 Mbps 4,500 (1.37) 9.38 Mbps 4,150 (1.26) 12.5 Mbps 4,000 (1.22) 16.67 Mbps 3,300 (1.00) Asymm Line Rate (DS/US) Distance in feet (km) 4.17 Mbps/1.56 Mbps (Mode 0) 6,000 (1.83) 9.38 M ...
-
Patton electronic 2168 - page 27
27 Notes _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ ___________________________________________________ ...
-
Patton electronic 2168 - page 28
28 Notes _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ ___________________________________________________ ...
¿Tienes una pregunta acerca de Patton electronic 2168?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Patton electronic 2168, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Patton electronic 2168 probablemente compartirá una forma de solucionarlo.