-
Bloomfield 8573 - page 1
BLOOMFIELD INDUST RIES 2 ERIK CIRCLE , P . O. Box 280 V erdi , NV 8943 9 Cust omer Servi ce ( 775) 345 -0444 Ext .502 fax: (775) 345-0569 www .well sbl oomfi eld. com p/n 75804 Rev. (-) M611 011802 cps 611 OWNERS M A NUAL For MODUL A R BREWING SYSTEMS MODELS POUR OVER AUTOMATIC AUTOMATIC UNITS UNITS UNITS WITH FAUCET 8542 8541 8540 8543 8573 8572 8 ...
-
Bloomfield 8573 - page 2
NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged b y skilled personnel before le aving the factory. Upon acceptance of this shipm ent, the transportation company assumes full responsibility for its safe delivery. IF SHIPMENT ARRIVES DAMAGED: 1. VISIBLE LOSS OR DAMAGE: Be certain that any vi ...
-
Bloomfield 8573 - page 3
TABLE OF CONTENTS Thank You for purcha sing this Bloomfield Industries appliance. Proper installation, professional operation and consistent maintenance of this appliance w ill ensure that it gives you the very best performance and a long, economical service life. This ma nual contains the information needed to properly install this appliance, and ...
-
Bloomfield 8573 - page 4
FEATURES AND OPERATING CONTROLS Fig. 1 Fea tures & Operating Controls 2 ...
-
Bloomfield 8573 - page 5
PRECAUTIONS AND GENERAL INFORMATION WA RNI NG: Electric Shock Hazard All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not open any access panels which require the use of tools. Failure to heed this warning can result in electrical shock. WA RNI NG: Injury Hazard All installation procedu ...
-
Bloomfield 8573 - page 6
INSTALLATION INSTRUCTIONS RE A D THIS CAREFULL Y BEFORE ST ARTING THE INST A LLA TIO N REFER TO EXPLODED VIEWS PAGES 18 thru 22 FOR COMPONENT NAMES/NUMBERS Unpack the unit. Inspec t all components fo r completeness and condition. Ensure that all packing materials have been removed from the unit. Verify that the Spray Head Gasket (#33) and Spray Dis ...
-
Bloomfield 8573 - page 7
INSTALLATION INSTRUCTIONS (contin ued) NOTE: This equipment must be installed to comply with applicable federal, state an d local plumbin g codes and ordinanc es. WARNING ELECTRIC SHOCK HAZARD: Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide suc h a ground. Electrical shock will cause de ...
-
Bloomfield 8573 - page 8
OPERATION Fig. 4 Brewer Operation Diagram A. STAR T-UP For initial start-up, or if the brewer has not been used for an extended period of time: ♦ Be sure spray disk and brew ga sket are properly installed in the brew head. ♦ Be sure the water supply is properly connecte d and the water supply valve is turned ON . ♦ Be sure the W ATER TANK IS ...
-
Bloomfield 8573 - page 9
OPERAT ION (continu ed) WATER HEATER Water temperat ure is sensed by a thermobulb insert ed into the water tank. This temperature signal is fed to the thermostat, which controls line power to the heating elemen t. The setpoint temperature is adjustable at the therm ostat. The elem ent is prot ected fr om over- temperature by a hi -limit thermostat. ...
-
Bloomfield 8573 - page 10
BREWING COFFEE CA UTI ON: Burn Hazard Exposed surfaces of the brewer, brew chamber and decanter m ay be HOT to the touch, and can cause serious burns. CA UTIO N: Burn Hazard To avoid splashing or over- flowing hot liquids, ALWAYS place an empty decanter under the brew chamber before starting the brew cycle. Failure to comply can cause serious burns ...
-
Bloomfield 8573 - page 11
CLEANING INSTRUC TIONS PROCEDURE: Clean Coffee Brewe r PRECAUTIONS: Disconnect bre w er fro m electric power. Allow brewer to cool. FREQUENCY: Dail y TOOLS: Mild Detergent, Clean Sof t Cloth or Sponge Bristle Brush. 1. Disconnect brewer from electric power. Allo w brewer to cool before cleaning. 2. Remove and empty de ca nters. 3. Remove and empty ...
-
Bloomfield 8573 - page 12
10 TROUBLESHOOTING SUGGESTI ONS SUGGESTED REMEDY Check po wer supply cord Check / reset circuit breaker Set for desired temperature Allow to cool Reset hi-limit (8786, 8788) Examin e w iring & connec tors, thermostat and heating element Repair/replace as needed Be sure to add sufficient water Increase wat er amount Adjust am ount of ground s Ad ...
-
Bloomfield 8573 - page 13
SERVICING INSTRUCTIONS ACCESS PANELS Each warmer plate has a center stud which screws into a bracket. Remove warmer plates by turning counter-clockwise. Solenoid door is held by two screws and a retaining lip. Front Panel (In-Line Models) and To p / Rear Panel (3-Station Models): a. Remove warmer plate b y turning counter-clockwise until it unscre ...
-
Bloomfield 8573 - page 14
SERVICING INSTRUCTIONS (continued) TEMPERATURE ADJUSTMENT Unplug power cord or turn circuit breaker OFF. Remove top panel. Pull vent tube out of tank lid an d insert a thermometer of known accuracy in vent hole. Reconnect brewer to electrical power. Place an empty decanter under brew chamber. Energize brewer and pour o ne decanter (6 4 oz.) of cold ...
-
Bloomfield 8573 - page 15
SERVICING INSTRUCTIONS ( continued) IMPORTA NT: Water pressure must be betwee n 20 p.s.i and 90 p.s.i. flowing pressure. If wate r pressure e xceeds this value, or if water pressure varies g reatly, a pressu re regulator must be installed in the w ater s upply line. IMPORTA NT: Before se tting assembly into tank, make sure tank lid gasket is proper ...
-
Bloomfield 8573 - page 16
SERVICING INSTRUCTIONS (continued) REPLACE SOLENOID Symptom: Automatic brewer will not flow water; or, automatic brewer d rips continuously from brew head. Unplug power cord or turn circuit breaker OFF . Turn OFF and disconnect w ater supply from brewer inlet fitting. A. (OLD-STYLE) Remove hex nut holding inlet fitting into back of brewer. Remove t ...
-
Bloomfield 8573 - page 17
SERVICING INSTRUCTI ONS (continued) IMPORTA NT: When replacing water faucet coil, also rep lace seal gaskets. NOTE : Any abrasion or roughness on the flat end of the seat cup will re quire replacing the seat cup: Work the seat cup out of the bonnet and off of the end of the stem. Install a ne w seat cu p, making sure the k nob on t he stem is fully ...
-
Bloomfield 8573 - page 18
CA UTION - CH EMICA L BU RN HA Z A RD Deliming chem icals are caustic. W ear appropriate pr otective gloves and goggles during this procedure. Never siphon deliming chemicals or solutions by mou th. This operation should only be perfo rmed by qualified and ex- perienced service personnel. IMPORT ANT: DO NOT spill, splash or pour water or deliming s ...
-
Bloomfield 8573 - page 19
7. Set the tank back into the bre wer. Reassemble the tank lid to the water tank. Make sure the gask et is properly in place, then reinstall the hold-down strap. 8. Reinstall wiring to heating element and ther mostat. Reinstall the hi-limit thermostat (if removed). For brew ers with hot water faucet, reassemble fa ucet piping. Verify that all inter ...
-
Bloomfield 8573 - page 20
EXPLODED VIEW & PARTS LIST CABINET & RELATED COMPONENTS 18 ...
-
Bloomfield 8573 - page 21
EXPLODED VIEW & PARTS LIST (continued) 19 ITEM P A RT NO. DESCR IPTION USED ON 1 8700-16 W armer Cov er Plate, Black All 8875- 149 20 8543-23 T i nnerman Nut , #8 (not shown ) All 2 3 8 543 -6 9 H ey co B us hi ng Al l 33 854 3-42 S pr ay Head Gaske t All 34 827 27 S pray Dis k All 34a 854 3-45 S pr ay Head Retai ner All 35 857 2-34 Door , Sole ...
-
Bloomfield 8573 - page 22
EXPLODED VIEW & PARTS LIST (continued) HOT WATER TANK ASSEMBLY 20 ITEM P ART NO. DESCRI PTION USED ON 13 8043-5 Hol d Down S trap All 50 8512- 51 Therm ostat Al l 52 8512-41 Seal Washer All 54 8043-12 T an k Cover Gasket All 56 8043-30 Seal G asket All 58 8540-6 Hot Water Coil 8540, 857 2, 8574 59 8043-8 Inl et Elbow All 60 8043-15 Vent Tube Al ...
-
Bloomfield 8573 - page 23
ELECTRICAL COMPONENTS EXPLODED VIEW & PARTS LIST (continued) 21 2 8572-18 W armer Element, 120V 100W All 30 6710-23 W ar mer ON /OFF Switc h All 31 8572-24 B REW Sw itch, push-button 8572, 8573 , 8574 8707-55 B REW SWI TCH , momen tary rock er 8540, 8541 32 8718-31 R EADY TO BREW Indicator Light All 36 6407-15 C ord & Cap As semb ly , NEMA ...
-
Bloomfield 8573 - page 24
EXPLODED VIEW & PARTS LIST (continued) INTERNAL PLUMBING COMPONENTS 22 ITEM P ART NO. DESCRIPTION USED ON 60 8043-15 V ent T ube All 61l 8 8540-3 Faucet Outlet T ub e As sembly 8540, 8572 & 8574 9 8540- 4 Formed Inlet T ube Assembly 8540, 8572 & 8574 10 8551-30 1/4“ Male Flare x 1/ 8 ” FPT 8540, 8572 & 8574 1 1 8514-26 N eedle V ...
-
Bloomfield 8573 - page 25
WIRING DIAGRAMS 23 ...
-
Bloomfield 8573 - page 26
WIRING DIAGRAM 24 ...
-
Bloomfield 8573 - page 27
WIRING DIAGRAM (continued) 25 ...
-
Bloomfield 8573 - page 28
Bloo mfield In dustri es, Inc. Divisi on of C arrier Refrig eratio n Blo om fiel d In dust ri es Canad a Li mi ted Divisi on of C arrier Refrig eratio n PO. Box 280 V erd i, NV . 894 39 T elephone ( 775)345-0 444 Fax (888)492-27 83 Service: (888)492-2782 website: ww w .wellsbloomfield.com 5850 Keaton Cr esent Mississauga, Ont ario , Canada L5R 3K 2 ...
¿Tienes una pregunta acerca de Bloomfield 8573?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Bloomfield 8573, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Bloomfield 8573 probablemente compartirá una forma de solucionarlo.