Español dropdown-ico

Manual de instrucciones ALFA AWAP08O-11gHP

61 de páginas 5.98 mb
Descargar

Pasar a la página of 61

Summary
  • ALFA AWAP08O-11gHP - page 1

    Wireless LAN Device Series WLAN Outdoor Bridge AWAP08O-11gHP User Manual V ersion. 1.2.1 (25.03.2005) ...

  • ALFA AWAP08O-11gHP - page 2

    2 T able of Content s Preface............................................................................................................................ 3 Ch 1. AWAP08O-11gHP Installatio n .............................................................. . ............. . 4 Packing List ................................................................ ...

  • ALFA AWAP08O-11gHP - page 3

    3 Preface This guide is for the networking professi onal who installs and manages the Ziwell AWAP08O-11gHP outdoor pr o duct, hereafter referred to as the “ d evice”. T o use this g u ide, you should have experience working with the TCP/IP configuration and be familiar with the concepts and terminology of wireless local area networks. ...

  • ALFA AWAP08O-11gHP - page 4

    4 Ch 1. AWAP08O-11gHP Ins t allation Packing List Before you start to inst all the ODU, make sure the package cont ains the following items ： z Wireless Outdoor Bridge unit * 1 z Mounting Kit * 1 z W aterproof (IP67) RJ-45 Cable (30M) * 1 z W aterproof (IP66) RF Cable (1M) * 1 z Power Over Ethernet Kit * 1 z Ground Wire * 1 z 2.5” /4” U bolts ...

  • ALFA AWAP08O-11gHP - page 5

    2.5” /4” U bolt and Anchor Hardware Inst allation Once you check off everything from the p ackage, you can st art to install the ODU. Y ou can mount to a pipe, a pole or to the side of a building. The steps are showed in the following ： 1. Y ou must mount the O DU into the bracket first. Note: ALL the 4 screws had been tightened onto the ODU ...

  • ALFA AWAP08O-11gHP - page 6

    6 W all Mounting Figure 3. Af ter checking the ODU is mount ed well, you can connect the following two cables: the Waterproof RJ-45 network cable to “P+ DATA OUT” port of ODU and the RF cable to ant enna port. Additional waterproof tool, such as waterproof tape, is recommended to use to enhance the waterproof function. It is sugges ted to have ...

  • ALFA AWAP08O-11gHP - page 7

    7 If the RJ-45 cable’ s length is not l ong enough to connect to your network device for indoor part s installation, you can extend the cable length. However , make sure the maximum lengt h of the RJ-45 cable is shorter than 100M (about 109 yards) for normal operation under IEEE 802.3 standards. When you plug the regular RJ-45 cable into the PoE ...

  • ALFA AWAP08O-11gHP - page 8

    8 Ch 2. First T ime Configuration Before S t art to Configure There are two interfaces to configure the device, one is web-browser interface, and the other is Secure Shell CLI interface. T o access the configuration interfaces, make sure y ou are using a computer connected to the same network as the device. T he default IP address of the device is ...

  • ALFA AWAP08O-11gHP - page 9

    9 The device provides 3 dif ferent operation modes and the wireless radio of device can act as AP/Client/WDS. The operati on mode is about the communication mechanism between the wired Ethernet NIC and wireless NI C, the following is the types of operation mode. Router The wired Ethernet (W AN) port is used to connect with ADSL/Cable modem and the ...

  • ALFA AWAP08O-11gHP - page 10

    10 survey and connect to the device. The device only allows the WDS connection. WDS+AP This mode combines WDS plus AP modes, it not only allow s W DS connections but also the wireless clients can su rvey and connect to the device. The following table shows the supporting combination of operation and wireless radio modes. Bridge Router WISP AP V v x ...

  • ALFA AWAP08O-11gHP - page 11

    11 Examples of Configuration Internet ADSL 192.168.2.x 192.168.3.x 192.168.3.x 192.168.2.x 192.168.2.x 192.168.2.x AP - Bridge WDS+AP - Bridge WDS+AP - Router Infrastructure Client – Router (WISP) Infrastructure Client - Bridge 192.168.2.x DEV 1 LAN 192.168.2.254 /24 WAN PPPoE connection W i re l e s s C h a nn e l / SS I D 11 / AWAP08O-11gHP MAC ...

  • ALFA AWAP08O-11gHP - page 12

    12 Configure DEV1: 1. Connect the ADSL modem to Ethernet por t of device using Ethernet cable. 2. Access the web server ( http://192.168.2.254 ) of device from the wireless station. 3. Use W izard page to setup device. 4. Press “Next>>” button then set the “Operation Mode” to “Router” mode. 5. Press “Next>>” button then ...

  • ALFA AWAP08O-11gHP - page 13

    13 7. Press “Next>>” button then select the “ PPPoE” for “W AN Access T ype” and fill in the “User Name” and “Password” fields. 8. Press “Next>>” button then select the “AP+WDS” for “m ode” and change the SSID to “ AWAP08O-11gHP ”. 9. Press “Next>>” button then select “None” for “Encry ...

  • ALFA AWAP08O-11gHP - page 14

    14 10. W ait for refreshing web page. 11. Use “WDS Settings” page to configure WDS. 12. Enable WDS function and add the B SSID of DEV2 to “Current WDS AP List”. ...

  • ALFA AWAP08O-11gHP - page 15

    15 13. Since we access the device by wireless c onnection, it may temporarily disconnect when applying the WDS setting. After re-c onnecting to the device, use the “Status “ page to check the settings. ...

  • ALFA AWAP08O-11gHP - page 16

    16 Configure DEV2: 1. Access the web server ( http://192.168.2.254 ) of device from the Ethernet port. Caution If you configure multiple devices in the same PC, since the devices have the same default IP address but different MAC addresses, it may cause you can’t access the web server of device. If the situation h appens, please try to clean the ...

  • ALFA AWAP08O-11gHP - page 17

    17 5. Press “Next>>” button then set th e IP address of LAN interface. 6. Press “Next>>” button then select the “AP+WDS” for “m ode” and change the SSID to “ AWAP08O-11gHP ”. 7. Press “Next>>” button then select “None” for “Encryption” then press “Finished” button. ...

  • ALFA AWAP08O-11gHP - page 18

    18 8. W ait for refreshing web page. 9. Access the web server by new IP addr ess “192.168.2.202” then use “LAN Interface” page to disable DHCP Server . 10. W ait for refreshing web page. 11. Use “WDS Settings” page to configure WDS. ...

  • ALFA AWAP08O-11gHP - page 19

    19 12. Enable WDS function and add the B SSID of DEV1 to “Current WDS AP List”. 13. Use the “S tatus “ page to check the settings. ...

  • ALFA AWAP08O-11gHP - page 20

    20 ...

  • ALFA AWAP08O-11gHP - page 21

    21 Configure DEV3: 1. Access the web server ( http://192.168.2.254 ) of device from the Ethernet port. Caution If you configure multiple devices in the same PC, since the devices have the same default IP address but different MAC addresses, it may cause you can’t access the web server of device. If the situation h appens, please try to clean the ...

  • ALFA AWAP08O-11gHP - page 22

    22 5. Use the “S tatus “ page to check the settings. ...

  • ALFA AWAP08O-11gHP - page 23

    23 Configure DEV4: 1. Access the web server ( http://192.168.2.254 ) of device from the Ethernet port. Caution If you configure multiple devices in the same PC, since the devices have the same default IP address but different MAC addresses, it may cause you can’t access the web server of device. If the situation h appens, please try to clean the ...

  • ALFA AWAP08O-11gHP - page 24

    24 5. Press “Next>>” button then set th e IP address of LAN interface. 6. Press “Next>>” button then select the “DHCP Cl ient” for “W AN Access T ype”. 7. Press “Next>>” button then select the “Client” for “m ode” and change the SSID to “ AWAP08O-11gHP ”. 8. Press “Next>>” button then sele ...

  • ALFA AWAP08O-11gHP - page 25

    25 9. W ait for refreshing web page. 10. Change the IP address of your PC to 192.168.3.x then access the web server by the new IP address “192.168.3.1” and use “S tatus” page check the setting. 11. If the “S tate” of “W irele ss Configuration” is not “Connected” or you want to refresh the “RSSI “, please use “Site Survey? ...

  • ALFA AWAP08O-11gHP - page 26

    26 ...

  • ALFA AWAP08O-11gHP - page 27

    27 Configure DEV5: 1. Access the web server ( http://192.168.2.254 ) of device from the Ethernet port. Caution If you configure multiple devices in the same PC, since the devices have the same default IP address but different MAC addresses, it may cause you can’t access the web server of device. If the situation h appens, please try to clean the ...

  • ALFA AWAP08O-11gHP - page 28

    28 5. Press “Next>>” button then set th e IP address of LAN interface. 6. Press “Next>>” button then select the “Client” for “m ode” and change the SSID to “ AWAP08O-11gHP ”. 7. Press “Next>>” button then select “None” for “Encryption” then press “Finished” button. ...

  • ALFA AWAP08O-11gHP - page 29

    29 8. W ait for refreshing web page. 9. Access the web server by the new IP address “192.168.2.205” and use “LAN Interface” page to disable DHCP Server . 10. W ait for refreshing webpage. 11. Use “S tate” page to check setting. ...

  • ALFA AWAP08O-11gHP - page 30

    30 12. If the “S tate” of “W irele ss Configuration” is not “Connected” or you want to refresh the “RSSI “, please use “Site Survey” page to re-connect a AP . ...

  • ALFA AWAP08O-11gHP - page 31

    31 Basic Settings Disable Wireless LAN Interface Disable the wireless interface of device Band: The device supports 2.4GHz(B), 2.4GHz (G) and 2.4GHz(B+G) mixed modes. Mode: The radio of device support s different modes as following: 1. AP The radio of device acts as an Access Point to serves all wireless clients to join a wireless local network. 2. ...

  • ALFA AWAP08O-11gHP - page 32

    32 Et her net Ac ce s s Po i nt A P Client 1 ( Infr ast ruct ure ) AP Clie nt 2 ( Inf rast ruct ure ) PC 2 PC 1 z Ad Hoc : This type provides a peer-to-peer communication between wireless stations. All the communication is done from Client to Client without any Access Point involved. Ad Hoc networking must use the same SSID and channel for establis ...

  • ALFA AWAP08O-11gHP - page 33

    33 1 1 2462 Americas, EMEA, Japan, and China 12 2467 EMEA and Japan only 13 2472 EMEA and Japan only 14 2484 Japan only When set to “Auto”, the device will find the least-congested channel for use. Associated Client Show the information of active wireless client stations that co nnected to the device. ...

  • ALFA AWAP08O-11gHP - page 34

    34 Advanced Settings These settings are only for more technically advanced users who have sufficient knowledge about wireless LAN. These settings sho uld not be changed unless you know what effect the changes will ha ve on your device. The default setting is optimized for the normal operation. For specific application, setting configuration will re ...

  • ALFA AWAP08O-11gHP - page 35

    35 can be useful in areas where many client devices are associating with the device, or in areas where the clients are far ap art and can detect only the device and not each other . Y ou can enter a setting ranging from 0 to 2347 bytes. Dat a Rate The standard IEEE 802.1 1b/1 1g support s 1, 2, 5.5,1 1/6, 9, 12, 18, 24, 36, 48 and Mbps dat a rates. ...

  • ALFA AWAP08O-11gHP - page 36

    36 Ethe rne t DEV-1 DE V-2 W irele ss S ta tio n m o ve s between the coverage areas Block WLAN Relay (Isolate Client) The device supports isolation funct ion. If you are building a public Wireless Network, enable this function can provide better security . The device will block packet s between wireless client s (relay). All the wireless clients c ...

  • ALFA AWAP08O-11gHP - page 37

    37 Configuring Wireless Security This device provides complete wireless security function include WEP , 802.1x, WP A-TKIP , WP A2-AES and WP A2-Mixed in different mode (see the Security Support T able). The default security setting of the encryption function is disabled. Choose your preferred security setting depending on what security function you ...

  • ALFA AWAP08O-11gHP - page 38

    38 refer to the following setting of the WEP encryption: z 64-bit WEP Encryption ： 64-bit WEP keys are as same as the encryption method of 40-bit WEP . Y ou can input 10 hexadecimal digit s (0~9, a~f or A~F) or 5 ACSII chars. z 128-bit WEP Encryption ： 128-bit WEP keys are as same as the encryption method of 104-bit WEP . Y ou can input 26 hexa ...

  • ALFA AWAP08O-11gHP - page 39

    39 WP A Encryption Setting WP A feature provides a high level of assurance for end-users and administrators that their data will remain private and access to their network restricted to authorized users. Y ou can choose the WP A encryption and select the Authentication Mode. WP A Authentication Mode This device supports two WP A modes. For personal ...

  • ALFA AWAP08O-11gHP - page 40

    40 Configuring as WLAN Client Adapter This device can be configured as a wir eless Ethernet adapter . In this mode, the device can connect to the other wirel ess stations (Ad-Hoc network type) or Access Point (Infrastructure netw ork type) and you don’t need to install any driver . Quick st art to configure Step 1. In “Basic Settings” page, c ...

  • ALFA AWAP08O-11gHP - page 41

    41 The alternative way to configure as following: Step 1. In “Wireless Site Survey” page, select one of the SSIDs you want to connect and then press “Connect” button to est ablish the link. Step 2. If the linking is established succe ssfully . It will show the message “Connect successfully”. Then press “OK”. Step 3. Then you can che ...

  • ALFA AWAP08O-11gHP - page 42

    42 Note ： If the available network requires aut hentication and data encryption, you need to setup the authentication and encryp tion before step1 and all the settings must be as same as the Access Point or S tation. About the detail authentication and data encryption settings, please refer the securi ty section. Authentication T y pe In client m ...

  • ALFA AWAP08O-11gHP - page 43

    43 Ch 3. Configuring WDS Wireless Distribution System (WDS) us es wireless media to communicate with the other devices, like the Ethernet does. This function allows one or more remote LANs connect with the lo cal LAN. T o do this, you must set these devices in the same channel and set MAC address of other devices you want to communicate with in the ...

  • ALFA AWAP08O-11gHP - page 44

    44 St ar topology ： Device Entries of WDS AP List S p anning T ree Protocol Required WDS1 The MAC Addresses of WDS2, WDS3, WDS4 and WDS5 No WDS2 The MAC Address of WDS1 No WDS3 The MAC Address of WDS1 No WDS4 The MAC Address of WDS1 No WDS5 The MAC Address of WDS1 No Ring topology ： Device Entries of WDS AP List Sp anning T ree Protocol Require ...

  • ALFA AWAP08O-11gHP - page 45

    45 Mesh topology ： PC 1 LAN3 LAN 4 PC 1 LAN 1 PC 1 LAN 2 LAN 5 WDS1 WDS2 WDS3 WDS4 WDS5 Device Entries of WDS AP List Spanning T ree Protocol R equired WDS1 The MAC Ad dresses of WDS2, WDS3, WDS4 and WDS5 Y es WDS2 The MAC Ad dresses of WDS1, WDS3, WDS4 and WDS5 Y es WDS3 The MAC Ad dresses of WDS1, WDS2, WDS4 and WDS5 Y es WDS4 The MAC Ad dresse ...

  • ALFA AWAP08O-11gHP - page 46

    46 Description Entries of WDS AP List Sp anning T ree Protocol Required Access Point The MAC Address of Repeater Y es Repeater The MAC Address of Access Point Y es Wireless Bridge Wireless Bridge can establish a wire less connection between two or more Wired LANs. When you decide to use the WDS as a Wireless Bridge, please refer the following instr ...

  • ALFA AWAP08O-11gHP - page 47

    47 Ch 4. Advanced Configurations Configuring LAN to W AN Firewall Filtering function is used to block pa cket s from LAN to W AN. The device supports three kinds of filter Port Filtering, IP Filter ing and MAC Filtering. All the entries in current filter table are used to restrict cert ain types of p ackets from your local network to through the de ...

  • ALFA AWAP08O-11gHP - page 48

    48 Addresses in current filter table. Once the source MAC Address of outgoing packet s match the MAC Addresses in the table, the firewall will block this packet from LAN to W AN. Configuring Port Forwarding (V irtual Server) This function allows you to automatically redirect common network services to a specific machine behind the NA T firewall. Th ...

  • ALFA AWAP08O-11gHP - page 49

    49 Finger 79 HTTP (Hyper T ext T ransfe r Protocol) 80 POP3 (Post Protocol) 1 10 NNTP (Net work Ne ws T ransport Protoc ol) 1 19 SNMP (Simpl e Network M anagement Protocol) 161 SNMP trap 162 SIP (Sessio n Initiation Protocol ) 5060 PPTP (Point-to-Point T unneling Proto col ) 1723 Multiple Servers behind NA T Example: In this case, there are two PCs ...

  • ALFA AWAP08O-11gHP - page 50

    50 Enable DMZ: Enable the “Enable DMZ”, and then click “Apply Cha nges” button to save the changes. DMZ Host IP Address: Input the IP Address of the comput er that you want to expose to Internet. Internet Device with Router Mode e nab led AP Client 1 DNS Host Configuring W AN Interface The device supports four kinds of IP configuration for ...

  • ALFA AWAP08O-11gHP - page 51

    51 S t atic IP Y ou can get the IP configuration data of S tatic-IP from your ISP . And you will need to fill the fields of IP addr ess, subnet mask, gateway address, and one of the DNS addresses. IP Addres s: The Internet Protocol (IP) address of W AN interface provided by your ISP or MIS. The address will be your network identifier besides your l ...

  • ALFA AWAP08O-11gHP - page 52

    52 DHCP Client (Dynamic IP) All IP configuration data besides DNS will obt ain from the DHCP server when DHCP-Client W AN Access T ype is selected. DNS1~ 3: The IP addresses of DNS provided by your ISP. DNS ( Domain Name Server) is u sed to map domain names to IP addresses. DNS maintain central list s of domain name/IP addresses and map the domain ...

  • ALFA AWAP08O-11gHP - page 53

    53 User Name: The account provided by your ISP Password: The password for your account. Connect T ype: “Continuous “ : connect to ISP permanently “Manual” : Manual conne ct/disconnect to ISP “On-Demand” : Automatically connect to ISP when user need to access the Internet. Idle Time: The number of inactivity minutes to di sconnect from I ...

  • ALFA AWAP08O-11gHP - page 54

    54 IP Addres s: The Internet Protocol (IP) addres s of W AN interface provide d by your ISP or MIS. The address will be your netwo rk ide ntifier besides your local netwo rk. Subnet Mask: The number use d to identify the IP subnet network, indicating whether the IP address can be re cognized on the LAN or if it must be reached through a gateway. Se ...

  • ALFA AWAP08O-11gHP - page 55

    55 2. Clone MAC address for S tatic IP W AN access type 3. Clone MAC address for PPPoE W AN access type ...

  • ALFA AWAP08O-11gHP - page 56

    56 4. Clone MAC address for PPTP W AN access type 5. Physical LAN interface MAC address clone ...

  • ALFA AWAP08O-11gHP - page 57

    57 Configuring DHCP Server 1. T o use the DHCP server inside the devi ce, please make sure there is no other DHCP server existed in the same network as the device. 2. Enable the DHCP Server option and assign the client range of IP addresses as following page. 3. When the DHCP server is enabled and al so the device router mode is enabled then the de ...

  • ALFA AWAP08O-11gHP - page 58

    58 A. Operation Mode B. Wirele ss Setting C. TCP/IP-LAN Setting D. TCP/IP-WAN Setting E. Firewall Setting G. Manage ment H. Apply Changes to Flash I. Reboo t to take effect 0. Exit A. Basic Settings B. Advanc ed Sett ings C. Security Setting s D. Access Control Se ttings E. WDS Settings 0. Exit A. IP Add ress :19 2.168.2.3 B. Subn et Mask :2 55.255 ...

  • ALFA AWAP08O-11gHP - page 59

    59 The System Management Password Protection Both Web-Browser and SSH configuration interfaces have p assword protection. T o disable the Web-Browser p assword protection just leave the “User Name” field to blank then c lick “Apply Changes” button. T o change the password of user “root” for SSH session, please use the CLI menu item G . ...

  • ALFA AWAP08O-11gHP - page 60

    60 wrong firmware won’t be accepted. After upgrading, the device will reboot and please note that depends on the version of firmware, the upgrading may cause the device conf iguration to be restored to the factory default setting, and the original configuration data will be lost! T o upgrade firmware, just assign the file name with full path then ...

  • ALFA AWAP08O-11gHP - page 61

    61 T o save & restore configuration data of device, just assign the target filename with full path at your local host, then you can backup configuration data to local host or restore configuration dat a to the device. ...

Fabricante ALFA Categoría Network Router

Los documentos del dispositivo ALFA AWAP08O-11gHP que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos ALFA
- manuales de instrucciones AWAP08O-11gHP
- hojas de producto ALFA
- folletos informativos
- o etiquetas energéticas ALFA AWAP08O-11gHP
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones ALFA AWAP08O-11gHP.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje ALFA AWAP08O-11gHP, instrucciones de servicio, instrucciones cortas o instrucciones de usuario ALFA AWAP08O-11gHP. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto ALFA AWAP08O-11gHP.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo ALFA AWAP08O-11gHP, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar ALFA AWAP08O-11gHP. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de ALFA AWAP08O-11gHP.

El manual de instrucciones completo de ALFA debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual ALFA AWAP08O-11gHP - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice ALFA AWAP08O-11gHP, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de ALFA AWAP08O-11gHP que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo ALFA AWAP08O-11gHP - que deben facilitarnos los primeros pasos durante el uso de ALFA AWAP08O-11gHP
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con ALFA AWAP08O-11gHP
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de ALFA AWAP08O-11gHP en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de ALFA AWAP08O-11gHP?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con ALFA AWAP08O-11gHP, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con ALFA AWAP08O-11gHP probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)