-
Little Wonder PRUNER - page 1
© 2006 Mantis, Div . of Schiller -Pfeiffer Inc. All Rights Reserved. Owner s Manual and Saf ety Instr uctions Pr uner “E” System ...
-
Little Wonder PRUNER - page 2
1 T able of Contents Important Information A. Introduction This attachment is designed for trimming light to medium size branches. B. Pruner Attachment Specification. C. Contents of the package 1. Pruner Attachment Assembly with plastic gear case cover 2. Chain Guide 3. Saw chain 4. Chain Guide cover D. Service Information Contact If you have quest ...
-
Little Wonder PRUNER - page 3
2 Safety and W arnings A. Safety Decals Please pay particular attention to the warning and information decals found on various parts of this Pruner Attachment unit. They are an important part of the safety system. These decals must be replaced in time due to abrasion, etc. It is your responsibility to replace the decals when they become hard to rea ...
-
Little Wonder PRUNER - page 4
3 General Safety Rules 1. Remove branches in sections. Maintain safe operating positions, to avoid risk of being struck by falling branches or by those that rebound after hitting the ground 2. Cover saw chain with guard during transport and storage. 3. Do not hit rocks, stones, tree stumps, and other foreign objects with the working unit. If saw ch ...
-
Little Wonder PRUNER - page 5
4 Extension cord chart ( minimum cord gauge (A WG) ) 17. Stay alert . W atch what you are doing. Use common sense. Do not operate tool when you are tired, ill or under the influence of alcohol or other drugs. 18. Check damaged parts . Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that ...
-
Little Wonder PRUNER - page 6
5 1. Unscrew the mounting nut from the Gear Case Cover . Open the cover . (Picture 3) 2. Mount the Chain Guide. Be sure that threaded pin fits into the opening in the guide bar . (Picture 4) 3. Fit the saw chain into the groove in the Chain Guide bar , and around the sprocket. 4. Be sure that pin of the chain tensioner fits into the lower hole of t ...
-
Little Wonder PRUNER - page 7
6 1. Loosen mounting nut and adjust the chain tension by turning the tensioner screw 2. Hold unit vertically , and tighten mounting nut 3. Move saw chain backwards on guide bar by hand. Saw chain should move freely on guide bar if it is in proper mesh with the sprocket. If saw chain is difficult to rotate or binds on guide bar , it is too tight. Re ...
-
Little Wonder PRUNER - page 8
7 Check the balance of the assembled unit. The handles and shoulder harness have been assembled at the factory and set according to the average size person. This can be adjusted to the operator ’ s preference by simple loosening the screws and sliding handles up or down the shaft. Re-tighten the screws. Balancing the unit If you need to cut 3”- ...
-
Little Wonder PRUNER - page 9
8 Service Maintenance Guide Area Maintenance procedure Frequency Spline male/female connection of the inner drive shaft Lubricate 20-25 Hrs Gear case Use a grease gun to insert lubricant into the grease nipple of the gear case. Use EP2 lithium grease 20-25 Hrs Guide bar Inspect/Clean/Replace The guide bar opening should be always a square. When it? ...
-
Little Wonder PRUNER - page 10
9 Area Maintenance procedure Frequency Oiling port Inspect/Clean Before each use Nose sprocket Clean/Lubricate Before each use Saw chain Inspect/Clean/Sharpen/lubricate/Replace Before each use Screws/Nuts/Bolts Inspect/T ighten/Replace Before each use Service Maintenance Guide Oiling port Grease port of the nose sprocket Area Maintenance Befor e Ev ...
-
Little Wonder PRUNER - page 11
10 • A Low-kickback Chain • Low-vibration Chain • Narrow-kerf Chain FILING TOOLS FOR FILING Saw Chain Sharpening Procedur e Square-Gr ound Filing WHO SHOULD PERFORM SQUARE-GROUND FILING? Most chain saw users will probably never need to use square ground chain, nor learn to perform square ground filing. But in areas where the timber is larger ...
-
Little Wonder PRUNER - page 12
11 GULLET FILING Approximately every 5th sharpening, clean out gullets with a 7/32" round file. File gullets from the inside out (the side opposite from sharpening). Leave a 1/8" shelf behind the gullet. The depth-gauge setting for all square-ground chisel chain is .025." 1. Drain the oil tank. 2. Remove sawdust. 3. Lubricate for rus ...
-
Little Wonder PRUNER - page 13
12 48 48 2 2 4 4 3 3 6 6 5 5 8 8 7 7 9 9 5 5 12 12 13 13 1 1 1 1 14 14 15 15 16 16 17 17 16 16 18 18 19 19 20 20 21 21 22 22 23 23 25 25 24 24 26 26 27 27 28 28 29 29 30 30 31 31 32 32 33 33 34 34 36 36 37 37 35 35 39 39 38 38 44 44 40 40 43 43 41 41 42 42 47 47 47 47 46 46 45 45 46 46 50 50 49 49 51 51 Pruner “E” System Exploded V iew ...
-
Little Wonder PRUNER - page 14
KEY # DESCRIPTION P ART # QTY 1 GEAR CASE COVER 3331 100 1 2 BEARING 6001-2Z 331 101 1 3 GEAR CASE 331 102 1 4 BEARING 627 331 103 1 5 BOL T M5X12 331500 5 6 GREASE FITTING 331104 1 7 SCREW , TENSIONER 331501 1 8 CHAIN TENSIONER 331 105 1 9 BOL T M6X30 331502 1 10 SHIM 331 106 1 1 1 BOL T M5X25 331503 1 12 PLASTIC CHAIN COVER 331 107 1 13 FLANGE LO ...
-
Little Wonder PRUNER - page 15
Specifications, descriptions, and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice. P/N 331701 2/06 MANTIS 1028 Str eet Road Southampton , P A 18966 (215) 355-9700 2 YEAR LIMITED SER VICE & W ARRANTY POLICY FOR PRUNER A TT ACHMENT MANTIS extends this limited w ...
¿Tienes una pregunta acerca de Little Wonder PRUNER?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Little Wonder PRUNER, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Little Wonder PRUNER probablemente compartirá una forma de solucionarlo.