-
Panasonic WV-BP332 - page 1
(Lens : option) Before attempting to connect or operate this product, please read these instructions completely. CCTV Cameras WV -BP330/WV -BP332/WV -BP334 FRANÇAIS ENGLISH ...
-
Panasonic WV-BP332 - page 2
WARNING: T O PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The serial number of this product may be found on the top of the unit. You should note the serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft. Mod ...
-
Panasonic WV-BP332 - page 3
CONTENTS PREFACE ........................................................................................................................................................................ 2 FEATURES ......................................................................................................................................................... ...
-
Panasonic WV-BP332 - page 4
-2- 1. The following functions are built-in. (1) Auto Light Control (ALC)/Electronic Light Control (ELC) (2) Back Light Compensation (ON: Photometric weight is given to the center of the screen/OFF: Effective if the object is not in the center of the screen) (3) Various External Sync Functions, including Gen-Lock 2. Signal-to-noise ratio of 50 dB 3 ...
-
Panasonic WV-BP332 - page 5
-3- 1. Do not attempt to disassemble the camera. To prevent electric shock, do not remove screws or covers. There are no user serviceable parts inside. Ask a qualified service person for servicing. 2. Handle the camera with care. Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handling or storage. 3. D ...
-
Panasonic WV-BP332 - page 6
-4- MAJOR OPERA TING CONTROLS AND THEIR FUNCTIONS WV- BP330 VIDEO OUT GEN-LOCK L INT AGC ON ALC BLC ON VIDEO G/L 75 VIDEO LEVEL V. PHASE H Ω LL OFF ELC OFF DC Hi-Z GND AC 24V IN 12 VIDEO OUT GEN-LOCK L INT AGC ON ALC BLC ON VIDEO G/L 75 VIDEO LEVEL V. PHASE H Ω LL OFF ELC OFF DC Hi-Z DC 12V IN VIDEO OUT GEN-LOCK L AGC ON ALC BLC ON VIDEO G/L 75 ...
-
Panasonic WV-BP332 - page 7
-5- q Auto Iris lens Connector This connector is for connecting the auto iris lens by a 4-pin male connector supplied as a standard accessory (Part No. YFE4191J100). w Flange-back Adjusting Ring This ring adjusts the back focal length or picture focus. Rotate this ring clockwise for a C-mount lens or counterclockwise for a CS-mount lens. e Lens (op ...
-
Panasonic WV-BP332 - page 8
-6- !0 Automatic Light Control / Electronic Light Control Selector (ALC , ELC) Lets you select the mode according to the lens type that is used with this camera. ALC: Select this mode when an auto iris lens (ALC lens) is used with this camera. ELC: Select this mode when a fixed iris lens or manual iris lens is used with this camera. !1 Back Light C ...
-
Panasonic WV-BP332 - page 9
-7- Cautions: 1. Connect to 12V DC (10.5V-16V) or 24V AC (19.5V-28V) class 2 power supply only. Make sure to connect the grounding lead to the GND terminal when the power is supplied from a 24V AC power source. 2. To prevent fire or electric shock hazard, use a UL listed wire VW-1, style 1007 cable for the Input Terminal. !7 Gen-lock Input Connecto ...
-
Panasonic WV-BP332 - page 10
-8- CONNECTIONS A. WV-BP330 (120V AC 60Hz) Connect the power cord to an electrical outlet of 120V AC 60Hz. B. WV-BP332 (12V DC) Connect the power cord to the DC 12V IN terminal on the rear panel of the WV-BP332. 12 V DC (10.5 V - 16 V) Copper wire #24 #22 #20 #18 size (AWG) (0.22mm 2 ) (0.33mm 2 ) (0.52mm 2 ) (0.83mm 2 ) Resistance 0.078 0.050 0.03 ...
-
Panasonic WV-BP332 - page 11
-9- C. The maximum extensible coaxial cable length between the camera and the monitor is shown below. Video Cable 1. It is recommended to use a monitor whose resolu- tion is at least equal to that of the camera. 2. Set the termination switch to the 75 Ω position on the last monitor. A. Use a 75 Ω coaxial cable. B. Set the termination switch to ...
-
Panasonic WV-BP332 - page 12
3. Wiring precautions: • Do not bend the coaxial cable into a curve whose radius is smaller than 10 times the cable’s diame- ter. • Never staple the cable, not even with circular sta- ples. Impedance mismatching will occur. • Never crush or pinch the cable. All of the above will change the impedance of the cable and cause poor picture quali ...
-
Panasonic WV-BP332 - page 13
-11- Installation of Auto Iris Lens Connector Install the lens connector (YFE4191J100) when using a video drive ALC lens. The installation should be made by qualified ser- vice personnel or system installers. (1) Cut the iris control cable at the edge of the lens connector to remove the existing lens connector and then remove the outer cable cover ...
-
Panasonic WV-BP332 - page 14
-12- Caution for Mounting the Lens The lens mount should be a C-mount or CS-mount (1”- 32UN) and the lens weight should be less than 450 g (0.99 lbs). If the lens is heavier, both the lens and cam- era should be secured by using the supporter. The protrusion at the rear of the lens should be as shown below: C-mount: Less than 11.5 mm (7/16”) CS ...
-
Panasonic WV-BP332 - page 15
-13- The following adjustment should be made by qualified service personnel or system installers. 1. Loosen the screws on the flange-back adjusting ring. 2. Turn the flange-back adjusting ring to the desired position. Caution: When the C-mount lens is mounted, do not rotate the ring counterclockwise by force after it stops. If the ring is rotated b ...
-
Panasonic WV-BP332 - page 16
-14- • Mounting from the bottom This camera is designed to be mounted from the bottom, as shown below. The mounting hole is a standard photographic pan-head screw size (1/4” - 20). • Mounting from the top Remove the mount adapter from the bottom of the camera by removing the two fixing screws. Attach the mount adapter to the top as shown in t ...
-
Panasonic WV-BP332 - page 17
-15- When the camera is aimed at a bright light, such as a spot light, or a surface that reflects bright light, smear or blooming may appear. Therefore, the camera should be operated carefully in the vicinity of extremely bright objects to avoid smear or blooming. Bright object Smear PREVENTION OF BLOOMING AND SMEAR ...
-
Panasonic WV-BP332 - page 18
Pick-up Device: 768 (H) x 494 (V) pixels, Interline Transfer CCD Scanning Area: 4.9 (H) x 3.7 (V) mm (Equivalent to scanning area of 1/3” pick-up tube) Synchronization: Internal, External, Line-locked or Multiplexed vertical drive (VD2) selectable Scanning System: 2 : 1 interlace Scanning: 525 lines / 60 fields / 30 frames Horizontal: 15.734 kHz ...
-
Panasonic WV-BP332 - page 19
Dimensions (without lens): 67 (W) x 55 (H) x 123 (D) mm [2-5/8” (W) x 2-3/16” (H) x 4-13/16” (D)] Weights (without lens): WV-BP330: 0.62 kg (1.40lbs) WV-BP332: 0.445 kg (0.98lbs) WV-BP334: 0.470 kg (1.04lbs) Weights and dimensions indicated are approximate. Specifications are subject to change without notice. -17- ST ANDARD ACCESSORIES Body C ...
-
Panasonic WV-BP332 - page 20
N0398-1048 YWV8QA4916BN Printed in Japan N 30 Imprimé au Japon Video Imaging Systems Company A Division of Panasonic Broadcast & Television Systems Company A Unit of Matsushita Electric Corporation of America Executive Office: One Panasonic Way 4H-2, Secaucus, New Jersey 07094 Regional Offices: Northeast: One Panasonic Way, Secaucus, NJ 07094 ...
¿Tienes una pregunta acerca de Panasonic WV-BP332?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Panasonic WV-BP332, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Panasonic WV-BP332 probablemente compartirá una forma de solucionarlo.