-
ADC P-90-250 - page 1
ADCP-90-250 Issue 1, November 1996 4-40001-2326 Page 1 1996, ADC Telecommunications, Inc. FTD1 36-Fiber Wall Box User Manual Content Page INTRODUCTIO N .......................................................................... . 1 Revision Histor y ...................................................................... . 1 Trademark Informatio n ...
-
ADC P-90-250 - page 2
ADCP-90-250 Issue 1, November 1996 Page 2 1996, ADC Telecommunications, Inc. Admonishments Important safety admonishments are used throughout this manual to warn of possible hazards to persons or equipment. An admonishment identifies a possible hazard and then explains what may happen if the hazard is not avoided. The admonishments — in th e ...
-
ADC P-90-250 - page 3
ADCP-90-250 Issue 1, November 1996 Page 3 1996, ADC Telecommunications, Inc. A . Functional Description 1.02 The FTD1 36-Fiber Wall Box ( Figure 1 ) is designed to provide a wall-mounted, or rack- mounted , secure, fiber cable terminal for use in small to medium-sized fiber networks and custome r premises applications. The wall box can accommod ...
-
ADC P-90-250 - page 4
ADCP-90-250 Issue 1, November 1996 Page 4 1996, ADC Telecommunications, Inc. 8515-A ACCESS COVER TO CABLE SERVICE LOOPS, SPLICES, ETC. KEY LOCKS CONNECTOR ACCESS COVERS Figure 2. Wall Box Features Chassis 1.06 The wall box has four mounting holes at the corners of a rectangle that i s 8. 5 inches (21.6 cm) high and 14 inches (35.6 c ...
-
ADC P-90-250 - page 5
ADCP-90-250 Issue 1, November 1996 Page 5 1996, ADC Telecommunications, Inc. 1.07 The splice trays are positioned on the back panel of the left side of the wall box (see Figure 4 ). They are secured by a horizontal splice strap assembly, the right end of whic h unhooks from the chassis. There is one radius limiter at each corner of this area. 8 ...
-
ADC P-90-250 - page 6
ADCP-90-250 Issue 1, November 1996 Page 6 1996, ADC Telecommunications, Inc. 2 . INSTALLATION Warning : Never install telephone equipment in a wet location or during a lightning storm . When installing or modifying telephone lines, disconnect lines at the network interface before working with uninsulated lines or terminals to prevent electrical ...
-
ADC P-90-250 - page 7
ADCP-90-250 Issue 1, November 1996 Page 7 1996, ADC Telecommunications, Inc. B . Rack Mounting the Wall Box 2.03 Th e FTD1 36-Fiber Wall Box can be rack-mounted in a 19-inch frame. This is accomplishe d by inserting a #12 screw throug h the 1/4-inch slots in each corner of the rear panel of the wall box, into the threaded mounting holes in the ...
-
ADC P-90-250 - page 8
ADCP-90-250 Issue 1, November 1996 Page 8 1996, ADC Telecommunications, Inc. CONNECTOR BODY BUSHING SPLIT RING COMPRESSION NUT 0SP CABLE 8993-A HUBBELL CONNECTOR (ASSEMBLED) CLINCH NUT Figure 6. Hubbell Connector Kit Cable Clamp Kits 2.07 The cable clamp kits ( Figures 7 an d 8 ) are installed on-site to separate the incomi ...
-
ADC P-90-250 - page 9
ADCP-90-250 Issue 1, November 1996 Page 9 1996, ADC Telecommunications, Inc. 8519-A CABLE CLAMP MOUNTING PL A TE R UBBER G R OMMET #4 MOUNTING SCREWS CABLE CLAMP Y OKES CABLE CLAMP T OP PL A TE CLAMP SCREWS Figure 7. Lower Cable Clamp Assembly Details 8520-A CABLE CLAMP MOUNTING PL A TE R UBBER G R OMMET #4 MOUNTING? ...
-
ADC P-90-250 - page 10
ADCP-90-250 Issue 1, November 1996 Page 10 1996, ADC Telecommunications, Inc. Routing Cables in Splice Trays (Two Methods) 2.09 Figures 10 and 11 show recommended methods for routing fiber cables and pigtail s in the two types of splice trays that are available for use in this wall box. Mounting Splice Trays 2.10 After all the splices in a give ...
-
ADC P-90-250 - page 11
ADCP-90-250 Issue 1, November 1996 Page 11 1996, ADC Telecommunications, Inc. Installing Fiber Cables 2.11 If you purchased a “bare” wall box and now need to instal l the fiber cables, install the angle d retainers and adapters one at a time in the vertical bulkhead plate in the front section of the wall box. The right side of eac h adapter ...
-
ADC P-90-250 - page 12
ADCP-90-250 Issue 1, November 1996 Page 12 1996, ADC Telecommunications, Inc. 11 CAUTION LASER RADIA TION DO NOT LOOK INTO CONNECTOR 12 3 CAUTION LASER RADIA TION DO NOT LOOK INTO CONNECTOR 45 6 CAUTION LASER RADIA TION DO NOT LOOK INTO CONNECTOR 78 9 CAUTION LASER RADIA TION DO NOT LOOK INTO CONN ...
-
ADC P-90-250 - page 13
ADCP-90-250 Issue 1, November 1996 Page 13 1996, ADC Telecommunications, Inc. A . Cleaning the Connectors and Adapters 3.02 Dust and other contaminants on fiber opti c connectors and adapters can seriously degrad e circuit performance. To prevent contamination, unused connectors and adapters must be protecte d wit h clean dust caps. Routine ter ...
-
ADC P-90-250 - page 14
ADCP-90-250 Issue 1, November 1996 Page 14 1996, ADC Telecommunications, Inc. 4. SYSTEM INTEGRATION SERVICES 401 ADC offers the following system integration services. For calls originating in the U.S.A . or Canada, dial 1-800-366-3891 , extension 3000 . For calls originating outside the U.S.A. or Canada, dial 612-946-3000 . Technical Assistance ...
-
ADC P-90-250 - page 15
ADCP-90-250 Issue 1, November 1996 Page 15 Contents herein are current as of the date of publ ication. ADC reserv es the right t o change the c ontents wi thout prior notice. In no event shall ADC be liabl e for any damag es resulting from loss o f data, loss o f use, or lo ss of profits and ADC further di sclaims an y and all liab ility for indire ...
¿Tienes una pregunta acerca de ADC P-90-250?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con ADC P-90-250, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con ADC P-90-250 probablemente compartirá una forma de solucionarlo.