Español dropdown-ico

Manual de instrucciones Huffy 89025

22 de páginas 1.14 mb
Descargar

Pasar a la página of 22

Summary
  • Huffy 89025 - page 1

    1 06/03 P/N 211543B Customer Service N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A. A Huffy Comp any IMPORT ANT! We appreciate your purchasing one of our many fine products. We are sure that you will be very satisfied with your selection. Although great care and effort have been taken, problems may occur. To ensure prompt and correct han ...

  • Huffy 89025 - page 2

    P/N 211543B 06/03 2 Install display boards in the marked locations. Each mounting location consist s of a mounting pole stub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate direction the board is facing). Corner “2” 73603 Corner “4” 62959 Corner “3” 88603 Corner “1” 9H909A Display boar ...

  • Huffy 89025 - page 3

    3 06/03 P/N 211543B 2 3 4 8 7 Assemble rims as shown below . 1 3. 5. 4. RIM ASSEMBL Y - Corner Locations 1 and 2 ...

  • Huffy 89025 - page 4

    P/N 211543B 06/03 4 6. W ARNING: Use of this product without proper installation of net clips, or when all net clips are not present could result in bodily harm. Be sure to follow directions carefully. Install net clips. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second ? ...

  • Huffy 89025 - page 5

    5 06/03 P/N 211543B Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP NET INST ALLA TION 7. 58 9 10 ...

  • Huffy 89025 - page 6

    P/N 211543B 06/03 6 At corner locations 1, 2, and 3 install the display pole (11) to the mounting pole stub. If required, secure the display pole (11), slide the display wedge (12) into position as shown. Tighten the set screw (13) to lock the display pole (11) in place. Use the second wedge only if necessary to tighten the fit. At corner location ...

  • Huffy 89025 - page 7

    7 06/03 P/N 211543B 8 11 49 16 10. 11 . 17 30 24 52 51 49 30 12. 49 8 55 54 54 57 44 57 55 13. 48 8 46 45 26 47 25 Install pole mount bracket (49) with carriage bolts (16) as shown. Tighten flange nuts (8) completely. Attach spacers (51, 52) to pole mount bracket (49) with bolts (24), washers (30), and nuts (17) as shown. IMPORTANT! Tighten until w ...

  • Huffy 89025 - page 8

    P/N 211543B 06/03 8 37 14. 38 38 24 24 17 17 29 29 39 39 59 37 42 Refer T o Instructions Included With Rim Hardware For Rim Assembly . 8 8 15. 59 27 Attach backboard support brackets (37) to the backboard frame using bolts (24), spacers (38), and nuts (17) as shown . Attach lower elevator tubes (29) to backboard support brackets (37) using spacers ...

  • Huffy 89025 - page 9

    9 06/03 P/N 211543B 17. 16. 21 21 27 59 37 42 59 Attach upper elevator tubes (21) to backboard support brackets (37) using sp acers (59), bolt (27), and nut (42) as shown. Attach backboard assembly to pole section (1 1). Install pole cap (43). NOTE: T wo people are recommended for this step. Use caution; elevator assembly is heavy . 11 42 21 43 21 ...

  • Huffy 89025 - page 10

    P/N 211543B 06/03 10 19. 55 18. Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05m) mark with pin (55). 23 23 17 65 15 15 24 18 20. 44” F AN MOLDED PLASTIC BOARD ASSEMBL Y - Corner Location 3 Attach adjustment rod (47) to lower elevator tubes (29) using bolt (27) spacer (59) and nut (42) a ...

  • Huffy 89025 - page 11

    11 06/03 P/N 211543B 27 59 59 42 21. 29 29 23 8 8 29 REFER TO INSTRUCTIONS INCLUDED WITH RIM HARDWARE FOR RIM ASSEMBLY 23 22. Attach lower elevator tubes (29) to backboard bracket s (23) using spacers (59) bolt (27) and nut (42) as shown. Bend top of backboard brackets (23) outward to match up with holes on backboard and secure using nuts (8) and b ...

  • Huffy 89025 - page 12

    P/N 211543B 06/03 12 27 21 42 21 22 22 23. 42 21 21 27 27 29 42 43 24. Attach backboard assembly to pole section (1 1). Then install pole cap (43). NOTE: T wo people are recommended for this step. Use caution; elevator assembly is heavy . Attach upper elevator tubes (21) to backboard bracket s (23) using spacers (22) bolt (27) and nut (42) as shown ...

  • Huffy 89025 - page 13

    13 06/03 P/N 211543B 42 27 29 29 47 59 59 26. Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05m) mark with pin (55). 55 A C B T o Set Backboard Height: A. While holding handle, remove pin (55). B. Move elevator up or down to desired height. C. Replace pin full length to lock system at desir ...

  • Huffy 89025 - page 14

    P/N 211543B 06/03 14 1. Attach elevator bracket (36) and reinforcement bracket (41) to pole section (1 1) using bolts (16) and nuts (8) as shown. 41 11 36 16 8 23 23 17 65 15 15 24 18 2. 44” F A N MOLDED PLASTIC BOARD ELEV A T OR ASSEMBL Y - Corner Location 2 Assemble backboard brackets (23) using sp acers (15) bolts (18, 24) and nuts (19, 17) as ...

  • Huffy 89025 - page 15

    15 06/03 P/N 211543B Bend top of backboard brackets (23) outward to match up with holes on backboard and secure using nuts (8) and bolt s as shown. Attach rim to backboard using using bolts and nut s (8) as shown. 27 60 60 42 3. 29 29 23 8 58 8 8 29 4. DO NOT USE WASHERS HERE ON SPRING RETURN STYLE RIMS REFER TO INSTRUCTIONS INCLUDED WITH RIM HARDW ...

  • Huffy 89025 - page 16

    P/N 211543B 06/03 16 20 21 42 21 56 56 5. 6. Attach upper elevator tubes (21) to backboard bracket s (23) using spacers (56) bolt (20) and nut (42) as shown. Attach backboard assembly to top pole section (1 1). Then install pole cap (43). NOTE: Tw o people are recommended for this step. Use caution; elevator assembly is heavy . 42 21 21 20 27 29 42 ...

  • Huffy 89025 - page 17

    17 06/03 P/N 211543B 5 6 6 31 28 5 31 7. Fig. A Fig. B 6 Insert locking pin (28) into bracket on adjustment tube (6). Insert cross pin (5) through hole in bracket and locking pin (28) as shown in figure A. Fit left handle (31) onto adjustment tube (6) so the bottom of adjustment tube (6) sits on the two small ribs of the handle as shown in figure B ...

  • Huffy 89025 - page 18

    P/N 211543B 06/03 18 28 6 31 53 28 50 31 53 8. Fig. C Insert spring (53) into back of locking pin (28) as shown. S pring (53) should rest between two small ribs at the back of the plastic handle as shown in Figure C. Insert top of trigger (50) into bracket on the adjustment tube (6) as shown. The plastic post of the handle pieces should go through ...

  • Huffy 89025 - page 19

    19 06/03 P/N 211543B 27 59 59 6 42 61 61 61 61 61 9. 10. 11 . 64 63 36 62 62 6 29 Attach adjustment tube to lower elevator tubes using bolt spacers and nut as shown. Finish handle assembly by attaching right handle using screws as shown. Insert lower adjustment rod (62) into bottom of adjustment tube (6), pull trigger to allow lower adjustment rod ...

  • Huffy 89025 - page 20

    P/N 211543B 06/03 20 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. WARNING Assemble 40” fan backboard as shown below with a st andard rim as shown. 40” F AN BACKBOARD ASSEMBL Y - Corner Location 4. 35 32 33 8 7 7 35 12. 34 8 ...

  • Huffy 89025 - page 21

    21 06/03 P/N 211543B Item #26 (2) Item Qty. Part No. Description 1 2 900033 Back Bracket 2 2 203796 T-Bolt, 3/8-16 x 5 3 2 200318 Bracket 4 2 203472 Spring 5 1 200215 Cross Pin 6 1 900006 Adjustment Tube - Upper 7 16* 203113 Bolt, Hex-Flange 5/16-18 x 2.5 8 34 203100 Nut, Hex-Flange 5/16-18 whiz Lock 9 48 201219 Clip, Smart Clips 10 4 204290 Net 11 ...

  • Huffy 89025 - page 22

    P/N 211543B 06/03 22 Item #27 (13) Item #18 (2) Item #20 (2) Item #33 (24) Item #35 (6) 22 of 22 Item #30 (8) Item #39 (4)* Item #40 (2) Item #59 (8) Item #60 (2) HARDW ARE IDENTIFIER (BOL TS & SCREWS) HARDW ARE IDENTIFIER (SPRINGS & W ASHERS) Item #16 (4) Item #22 (4) Item #63 (1) PLASTIC SP ACERS Item #24 (2) Item #7 (16) Item #2 (2) Item ...

Fabricante Huffy Categoría Board Games

Los documentos del dispositivo Huffy 89025 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Huffy
- manuales de instrucciones 89025
- hojas de producto Huffy
- folletos informativos
- o etiquetas energéticas Huffy 89025
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Huffy 89025.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Huffy 89025, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Huffy 89025. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Huffy 89025.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Huffy 89025, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Huffy 89025. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Huffy 89025.

El manual de instrucciones completo de Huffy debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Huffy 89025 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Huffy 89025, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Huffy 89025 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Huffy 89025 - que deben facilitarnos los primeros pasos durante el uso de Huffy 89025
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Huffy 89025
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Huffy 89025 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Huffy 89025?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Huffy 89025, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Huffy 89025 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)