-
Honeywell 3820i - page 1
3820, 3820i, 4820, 4820i Cordless Imaging Systems Quick Start Guide CRDLSS-02-QS Rev F 1/12 Aller à www.honeywellaidc.com pour le français. Vai a www.honeywellaidc.com per l'italiano. Gehe zu www.honeywellaidc.com für Deutsch. Ir a www.honeywellaidc.com para español. 日本語 : www.honeywellaidc.com をご覧ください。 如要到中? ...
-
Honeywell 3820i - page 2
Note: Refer to your user’s guide fo r information about cleaning your device. For localized language versions of this document, go to www.honeywellaidc.com. Getting Started Turn off the computer’s power be fore connecting the base, then power up the computer once the base is fully connected. When the base is connected and powered up, put the im ...
-
Honeywell 3820i - page 3
USB Connection Ke yboard W edge Connection ...
-
Honeywell 3820i - page 4
Serial (RS-232) Connection Reading T echniques The view finder projects an aiming beam that should be centered over the bar code. (T he 4820/4820i can be positioned in any direction for a good read. ) Hold the imager over the bar code, pull the trigger, and center the aiming beam on the bar code. The aiming beam is smaller when the imager is closer ...
-
Honeywell 3820i - page 5
Note: If the imager beeps 3 times when scanning a bar code, the link has not been established. If t he imager beeps once, the link has been established. Standard Pr oduct Defaults This bar code resets all stand ard product default settings. Standard Product Defaults ...
-
Honeywell 3820i - page 6
PC Interface Scan the bar code that describes the PC or interface you are using. RS-232 USB Keyboard (PC) Japan DOS/V USB Japanese Keyboard (PC) Emulate External Keyboard AT/PS2 Keyboard Wedge (Default) ...
-
Honeywell 3820i - page 7
Ke yboard Country Scan the Program Keyboard Country bar code below, then scan the numeric bar code(s) from the back of this sheet, then the Save bar code to program the keyboard for your country. As a general rule, the following characters are not supported by the imager for countries other than the United States: @ | $ # { } [ ] = / ‘ < > ...
-
Honeywell 3820i - page 8
Open Link Scan the Open Link bar code, then place the imager into the base to establish a link. Placing a different imager into the base establishes a new link and the old imager is unlinked. Override Locked Ima ger If you need to replace a broken or lost imager that is linked to a base, scan the Override Locked Imager bar code with a new imager, a ...
-
Honeywell 3820i - page 9
Tr i g g e r The following bar codes will allow you to use the reader in Manual Trigger mode (need to press the tr igger to read) or Presentation mode (the reader is activated when it “sees” a bar code). Streaming Presentation™ (4820/4820i) Note: Streaming presentation mode applies only to units with advanced illumination. Units with advanced ...
-
Honeywell 3820i - page 10
Reread Delay This sets the time period be fore the imager can read the same bar code a second time. Setting a reread delay protects against accidental rereads of the same bar code. Suffix If you want a carriage return after the bar code, scan the Add CR Suffix bar code . To add a tab after the bar code, scan the Add T ab Suffix bar code. Otherwise, ...
-
Honeywell 3820i - page 11
Add Code ID Prefix to all Symbologies Scan the following bar code if you wish to add a Code ID prefix to all symbologies at once. Note: For complete list of Code IDs, see the User’s Guide for your product at our website, www.honeywellaidc.com. Function Code T ransmit When this selection is enabled an d function codes are contained within the scan ...
-
Honeywell 3820i - page 12
Data Format Editor Instructions The following are abbreviated instru ctions for entering a data format. For complete instructions refer to yo ur User’s Guide, available at our website, www.honeywellaidc.com. 1. Scan the Enter Data Format symbol. 2. Primary/Alternate Format: scan 0 for Primary Format 3. Terminal Type: scan 099 for any terminal typ ...
-
Honeywell 3820i - page 13
Programming Chart 0 2 1 4 3 5 6 7 8 ...
-
Honeywell 3820i - page 14
A B C D E F 9 Save ...
-
Honeywell 3820i - page 15
Visual Xpress™ To obtain access to additional fe atures for the imager, use Visual Xpress, available from our website at www.honeywellaidc.com. F o r complete download instructions and descriptions of Visual Xpress features, refer to your User’s Guide. T echnical Assistance Contact information for technical s upport, product service, and repair ...
-
Honeywell 3820i - page 16
This document contains proprietary informa tion that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of HII. © 2008-2012 Honeywell International Inc. All rights reserved. Web Address: www.honeywellaidc.com ...
¿Tienes una pregunta acerca de Honeywell 3820i?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Honeywell 3820i, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Honeywell 3820i probablemente compartirá una forma de solucionarlo.