-
Axis Communications P1357 - page 1
AXIS P13 Series AXIS P1354 Network Camera AXIS P1357 Network Camera E N G L I SH Installation Guide ...
-
Axis Communications P1357 - page 2
Legal Considerations Video and audio surveillance can be regulated by laws that vary from country to country . Check the laws in your local region before using this product for surveillance purposes. This product includes one (1) H.264 decoder license and one (1) AAC decoder license. To purchase further licenses, contact your reseller . Liability E ...
-
Axis Communications P1357 - page 3
This product fullls the requirements for immunity according to EN 550 24 ofce and commercial environments Australia/New Zealand This digital equipment fullls the requirements for RF emission according to the Class B limit of AS/NZS CISPR 22. The product shall be connected using a shielded network cable (STP) that is properly grounded. Japa ...
-
Axis Communications P1357 - page 4
...
-
Axis Communications P1357 - page 5
AXIS P13 Series Safety Infor mation Read through this Installation Guide carefully before installing the product. Keep the Installation Guide for future reference. Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury . WARNING Indicates a hazardous situation which, if not avoided, could ...
-
Axis Communications P1357 - page 6
AXIS P13 Series Safety Instructions WARNING • The Axis product shall be installed by a trained professional. NO NO NO TICE TICE TICE • The Axis product shall be used in compliance with local laws and regulations. • To use the Axis product outdoors, or in similar environments, it shall be installed in an approved outdoor housing. • Store the ...
-
Axis Communications P1357 - page 7
AXIS P13 Series WARNING • Risk of explosion if the battery is incorrectly replaced. • Replace only with an identical battery or a battery which is recommended by Axis. • Dispose of used batteries according to local regulations or the battery manufacturer's instructions. 7 E N G L I SH ...
-
Axis Communications P1357 - page 8
8 ...
-
Axis Communications P1357 - page 9
AXIS P13 Series Installation Guide This Installation Guide provides instructions for installing AXIS P1354/P1357 Network Camera on your network. For other aspects of using the product, see the User Manual available at www .axis.com Installation Steps 1. Make sure the package contents, tools and other materials necessary for the installation are in ...
-
Axis Communications P1357 - page 10
AXIS P13 Series Hardware Overview 1 4 5 6 7 8 9 10 1 1 1 2 1 3 1 4 3 2 1 Focus puller 2 Zoom puller 3 LED indicator 4 P ower LED 5 Network LED 6 Control button 7 I/O terminal block 8 Iris connector 9 P ower connector* 1 0 RS485/422 1 1 SD card slot (microSD) 12 Audio in 13 Audio out 14 Network connector P oE * Not used for -E versions. 1 0 ...
-
Axis Communications P1357 - page 11
AXIS P13 Series LED Indicators Note • The Status LED can be congured to be unlit during normal operation. To congure, go to Setup > System Options > P orts & Devices > LED . See the online help for more information. • The Status LED can be congured to ash while an event is active. • The Status LED can be congured t ...
-
Axis Communications P1357 - page 12
AXIS P13 Series Connectors and Buttons For specications and operating conditions, see page 13 . Network Connector RJ45 Ethernet connector with P ower over Ethernet (P oE). NO NO NO TICE TICE TICE The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network shall be intended for their speci ...
-
Axis Communications P1357 - page 13
AXIS P13 Series RS485/RS422 Connector Two terminal blocks for RS485/RS422 serial interface used to control auxiliary equipment such as pan-tilt devices. SD Card Slot NO NO NO TICE TICE TICE • Risk of damage to SD card. Do not use sharp tools or excessive force when inserting or removing the SD card. • Risk of data loss. To prevent data corrupti ...
-
Axis Communications P1357 - page 14
AXIS P13 Series P ower Consumption Products DC P oE AXIS P1354 8-28 V DC max 7.2 W IEEE 80 2.3af/802.3at Type 1 Class 3 AXIS P1357 8-28 V DC max 7.9 W IEEE 80 2.3af/802.3at Type 1 Class 3 Connectors I/O Connector 4–pin terminal block For an example diagram, see Connection Diagrams on page 16 . Function Pin Notes Specications 0 V DC (-) 1 DC ou ...
-
Axis Communications P1357 - page 15
AXIS P13 Series Audio Connector 3.5 mm audio connectors (stereo) 1 2 3 1 Tip 2 Ring 3 Sleeve Audio Input Microphone/Line in Ground Audio Output Line out (mono) Ground RS485/422 Connector Two 2-pin terminal blocks for RS485/RS422 serial interface. The serial port can be congured to support: • Two-wire RS485 half duplex • Four-wire RS485 full ...
-
Axis Communications P1357 - page 16
AXIS P13 Series Connection Diagrams I/O Connector 1 2 3 4 1 0 V DC (-) 2 DC output 3.3 V, max 50 mA 3 Digital input 0 to max 40 V DC 4 Digital output 0 to max 40 V DC, open drain, 1 00 mA Install the Hardware Connect the Cables 1. Connect external input/output devices if required, such as alarm devices. For information about the terminal connector ...
-
Axis Communications P1357 - page 17
AXIS P13 Series - Connect an external power adapter to the power connector block. For wiring information, see page 14 . 5. Check that the indicator LEDs indicate the correct conditions, see LED Indicators on page 1 1 . Access the Product AXIS IP Utility and AXIS Camera Management are recommended methods for nding Axis products on the network and ...
-
Axis Communications P1357 - page 18
AXIS P13 Series 7. On the Focus page, click Fine-tune focus automatically and wait until automatic ne tuning is completed. 8. Click Enable iris . If the button is inactive the iris is already enabled. 9. If needed, make further adjustments under the Advanced tab . See the online help for more information. Focus Assistant To focus using the Focus ...
-
Axis Communications P1357 - page 19
AXIS P13 Series Reset to Factory Default Settings Important Reset to factory default should be used with caution. A reset to factory default will reset all settings, including the IP address, to the factory default values. Note The installation and management software tools are available from the support pages on www .axis.com/techsup To reset the ...
-
Axis Communications P1357 - page 20
Installation Guide V er . M2.2 AXIS P13 Series Date: June 20 15 © Axis Communications AB, 20 14 - 20 15 P art No. 1467 126 ...
¿Tienes una pregunta acerca de Axis Communications P1357?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Axis Communications P1357, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Axis Communications P1357 probablemente compartirá una forma de solucionarlo.