-
DeWalt DWE46101 - page 1
DWE46101 www . .eu ...
-
DeWalt DWE46101 - page 2
1 Figure 1 Figure 2 f c p a c f o d b h i n j k l m g ...
-
DeWalt DWE46101 - page 3
2 Figure 5 Figure 4 Figure 3 n r q n i j k d u e l m b ...
-
DeWalt DWE46101 - page 4
3 Figure 8 Figure 6 Figure 7 m l m t s h u ...
-
DeWalt DWE46101 - page 5
ENGLISH 32 MOR T AR RAKING KIT DWE46101 Congratulations! Y ou have chosen a D E WAL T tool. Y ears of experience, thorough pr oduct development and innovation make D E W AL T one of the most reliable partners for professional power tool users. T echnical Data DWE46101-LX DWE46101-QS Voltage V – 230 U.K. & Ireland V 115 – T ype 1 1 Power inp ...
-
DeWalt DWE46101 - page 6
ENGLISH 33 EC-Declaration of Conformity MACHINERY DIRECTIVE DWE46101 D E W AL T declares that these pr oducts described under T echnical Data are in compliance with: 2006/42/EC, EN 60745-1, EN 60745-2-3. These products also comply with Dir ective 2004/108/EC and 2011/65/EU. For more information, please contact D E W AL T at the following address or ...
-
DeWalt DWE46101 - page 7
ENGLISH 34 d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury . e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly . Do not ...
-
DeWalt DWE46101 - page 8
ENGLISH 35 damage or install an undamaged accessory . After inspecting and installing an accessory , position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time. h) Wear personal protective equipment ...
-
DeWalt DWE46101 - page 9
ENGLISH 36 e) Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades create frequent kickback and loss of control. Safety Warnings Specifi c for Grinding and Abrasive Cutting-Off Operations a) Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for whic ...
-
DeWalt DWE46101 - page 10
ENGLISH 37 • Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long hair can be caught in moving parts. • Threaded mounting of accessories must match the grinder spindle thread. For accessories mounted by flanges, the arbor hole of the accessory must fit the locating diameter of the flange. Accessories that do ...
-
DeWalt DWE46101 - page 11
ENGLISH 38 use of the mortar raking shroud could otherwise contaminate the working environment or pose an increased health risk to the operator and those in close proximity . DO NOT use under wet conditions or in the presence of flammable liquids or gases. This heavy-duty slot cutter is a professional power tool. DO NOT let children come into conta ...
-
DeWalt DWE46101 - page 12
ENGLISH 39 Attaching Side Handle (fi g.1) WARNING: Before using the tool, check that the handle is tightened securely . Screw the side handle (c) tightly into one of the holes (p) on either side of the gear case. Mounting and Removing Mortar Raking Shroud (fi g.3) NOTE: The supplied mortar raking shroud is only recommended for use with the ...
-
DeWalt DWE46101 - page 13
ENGLISH 40 2. T ur n cornering door locking lever (l) counterclockwise one full r otation. Grasp the corner door (m) and rotate open. 3. Place hands away from the wheel ar ea and position yourself so the open under side of the shroud is facing away fr om you. 4. T ur n the tool on and allow the tool to reach full speed before touching the tool to t ...
-
DeWalt DWE46101 - page 14
ENGLISH 41 as the activation of a ground fault interrupter , throwing of a circuit breaker , accidental unplugging, or power failure. If the switch is locked on when the power is connected, the tool will start unexpectedly . T o start the tool, slide the ON/OFF slider switch (g) toward the fr ont of the tool. T o stop the tool, release the ON/OFF s ...
-
DeWalt DWE46101 - page 15
ENGLISH 42 reconnecting the tool, depress and release the switch to ensure that the tool is off. P op-off Brushes The motor will be automatically shut off indicating that the carbon brushes are nearly worn out and that the tool needs servicing. The carbon brushes are not user -serviceable. T ake the tool to an authorised D E W AL T repair agent. Lu ...
-
DeWalt DWE46101 - page 16
ENGLISH 43 GUARANTEE D E W AL T is confident of the quality of its products and of fers an outstanding guarantee for professional users of the pr oduct. This guarantee statement is in addition to and in no way prejudices your contractual rights as a professional user or your statutory rights as a private non-professional user . The guarantee is val ...
-
DeWalt DWE46101 - page 17
ENGLISH 44 CUTTING ACCESSORY CHAR T Guard T ype Accessory Description How to Fit Grinder TYPE 1 GUARD Masonry cutting disc, bonded T ype 1 guard Backing flange Cutting wheel Threaded clamp nut Metal cutting disc, bonded Diamond cutting wheels ...
¿Tienes una pregunta acerca de DeWalt DWE46101?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con DeWalt DWE46101, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con DeWalt DWE46101 probablemente compartirá una forma de solucionarlo.