-
KitchenAid 1435 - page 1
- Installation Instructions 30” Built-In Microwave Convection Hood L IMPORTANT: Installer: Leave Installation Instructions with the Homeowner. Homeowner: Keep Installation Instructions for future reference. Save Installation Instructions for local electrical inspector’s use. READ THESE INSTRUCTIONS BEFORE YOU START TO INSTALL THIS UNIT. KEEP IN ...
-
KitchenAid 1435 - page 2
30” BUILT-IN MICRO WAVE /HOOD MODEL KHMC106 W INSTALLATION INSTRUCTIONS CONTENTS: Introduction ....................................................................... 1 Mounting Space .................................................................. 1 Wall Construction ............................................................... 2 Electrical ...
-
KitchenAid 1435 - page 3
INTRODUCTION Proper installation is the installer’s responsibility. A qualified technician should install this microwave oven. Make sure you have everything necessan/ for correct installation. It is the responsibility of the installer to comply with the installation clearances specified on the serial/rating plate. The serial/rating plate is locat ...
-
KitchenAid 1435 - page 4
WALL CONSTRUCTION Personal Injury or Property Damage Hazard l This microwave oven must be mounted against and supported by a flat, vertical wall. l This microwave oven must be attached with two lag screws to a minimum of one, vertical 2” x 4” wall stud. l Do Not mount microwave oven to an Island or peninsula cabinet. l The microwave oven top an ...
-
KitchenAid 1435 - page 5
ELECTRICAL REQUIREMENTS Electrical ground is required on this appliance. E-&~&Hazard l Checkwithaqualifiedelectricianifyouareindoubtastowhethertheapplianceisp~perlygrounded. Improper connection of the equipment-grounding conductor can result in electrical shock. l This appliance must be properly grounded. Failure to do so may result in elec ...
-
KitchenAid 1435 - page 6
HOOD EXHAUST DUCT When the hood is vented to the outside, a HOOD EXHAUST DUCT is required. All ductwork must be metal (do not use plastic duct). Check that all connections are made securely. Please read the following carefully: Fire Hazard Mntirg system must terminate to the outside. Do Not terminate the ductwoh in an attic or other enclosed space. ...
-
KitchenAid 1435 - page 7
TOOLS RECOMMENDED FOR INSTALLATION Phillips Screwdriver Electric Drill l/2”, 5/8” and 3/32’ Drill Bits 1 -l/2’ Wood Bit or metal hole cutter (if metal cabinet is used) Saw to cut exhaust opening (if needed) Knife or single edge razor Pencil Measure Tape Protective drop cloth for product and range. You may use part of the carton for protecti ...
-
KitchenAid 1435 - page 8
PREPARATION OF CARTON Utilization of the canon may make installation easier. CHECK THE PRODUCT FOR DAMAGE 1. Remove product and shipping pads. Visually check the product after removing from carton. Remove all packing material from inside the oven cavity. Check the oven for any damage, such as misaligned door, damaged gaskets around door or dents in ...
-
KitchenAid 1435 - page 9
VENTILATION SYSTEM THIS MICROWAVE OVEN/HOOD SYSTEM IS DESIGNED FOR ADAPTATION TO THREE TYPES OF HOOD VENTILATION SYSTEMS: A. Vertical Exhaust -- outside ventilation B. Horizontal Exhaust -- outside ventilation C. Recirculating -- non-vented, ductless Select the type required for your installation. Recirculating (ductless) installation requires CHAR ...
-
KitchenAid 1435 - page 10
HORIZONTAL EXHAUST (Continued) 2. Withdraw hood fan unit upward carefully (Fig.4). Figure 4 1. 3. Rotate hood fan unit l/4 turn as shown in Figure5 Figure 5 4. Replace hood fan unit into the oven unit. Be careful not to pinch the lead wire between the inner bracket and the hood fan unit (Fig.6). Figure 6 8 ...
-
KitchenAid 1435 - page 11
1 ,, .:y 2. -- .; . . . -A.,~*;-,-, .-. 5. Replace the fan cover bracket. Make sure the fan blades are visible through the rear openings in the cover before proceeding. Attach cover to unit with 3 screws (Fig. 7). The hood fan unit is now rotated for horizontal exhaust operation See page 11 for exhaust adaptor assembly installation instructions. C. ...
-
KitchenAid 1435 - page 12
PREPARATION OF WALL AND TOP CABINET MOUNTING TEMPLATES THIS PRODUCT CANNOT BE PROPERLY INSTALLED WITHOUT REFERRING TO THE MOUNTING INSTRUCTIONS FOUND ON BOTH TEMPLATES. READ AND FOLLOW MOUNTING INFORMATION ON BOTH TOP CABINET AND WALL TEMPLATES WALL AND TOP CABINET I personal Injury or property Dama* Hazard The mounting area on the top cabinet and ...
-
KitchenAid 1435 - page 13
5. If horizontal exhaust is used, attach the exhaust adaptor assembly to each of the mounting plates by aligning the holes on the assembly with the tabs on the plates, holding the as- sembly in place and bending the tabs to secure the assembly to the plates (Fig. 13). Exhaust Adaptor Assembly zontal exhaust only) Property Damage Hazard Place a port ...
-
KitchenAid 1435 - page 14
Thread the oower sunulv cord throueh the hole made at the bottom of the ton cabinet I Personal Injury Hazard Two people are required to lift this microwave. Failure to use more than one person during installation may result in oersonal iniurv. I Hang the unit on the lower edge of the mounting plates. Rotate the unit upward until it engages the uppe ...
-
KitchenAid 1435 - page 15
8. Use the two top cabinet mounting screws (C) and flat washers (D), supplied in the installation hardware, to attach the unit to the top cabinet. See Figurel6. Note: If mounting plates were installed using only toggle bolts, use the adjusting screws to attach the unit to the top cabinet. ommet (for metal Figure1 6 9. Make a bundle of the power sup ...
-
KitchenAid 1435 - page 16
4 I-? 4S72 PART NO. KHMCIOGW PRINTED IN U.S.A. ...
¿Tienes una pregunta acerca de KitchenAid 1435?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con KitchenAid 1435, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con KitchenAid 1435 probablemente compartirá una forma de solucionarlo.