Español dropdown-ico

Manual de instrucciones Gefen EXT-DPKVM-841

33 de páginas 0.55 mb
Descargar

Pasar a la página of 33

Summary
  • Gefen EXT-DPKVM-841 - page 1

    ® 8x1 DPKVM Switcher EXT-DPKVM-841 User Manual www.gefen.com ...

  • Gefen EXT-DPKVM-841 - page 2

    T echnical Support : T elephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 T echnical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday . Write T o: Gefen, LLC c/o Customer Service 20600 Nordhoff St Chatsworth, CA 9131 1 www .gefen.com support@gefen.com Notice Gefen, LLC reserves the right to make changes in the hard ware, packaging, and a ...

  • Gefen EXT-DPKVM-841 - page 3

    CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Front Panel Layout 5 Front Panel Descriptions 6 Back Panel Layout 7 Back Panel Descriptions 8 IR Remote Control Unit 8 Layout and Description 9 Installing the Battery 10 Setting the IR Channel 1 1 Connecting the 8x1 DPKVM Switcher 1 1 Wiring Diagram 12 Operating the 8x1 DPKVM Switcher 12 Front ...

  • Gefen EXT-DPKVM-841 - page 4

    1 INTRODUCTION Congratulations on your purchase of the 8x1 DPKVM Switcher . Y our complete satisfaction is very important to us. Gefen Gefen delivers innovative and progressive computer and electronics add-on solutions that harness integration, extension, distribution, and conversion technologies. Gefen’s reliable plug-and-play products supplemen ...

  • Gefen EXT-DPKVM-841 - page 5

    READ THESE NOTES BEFORE INST ALLING OR OPERA TING THE 8X1 DPKVM SWITCHER • The 8x1 DPKVM Switcher supports Pass-through EDID. The Switcher will use the EDID from the currently active input. • Dual Link resolutions up to 2560 x 1600 are supported. • HDCP content is not supported. • This Switcher does not support DHCP . • The default IR cha ...

  • Gefen EXT-DPKVM-841 - page 6

    3 FEA TURES Features • Front-panel switching using discrete select buttons • Supports resolutions up to 2560 x 1600 • Supports RGB and YCbCr color spaces • Green mode (low power consumption when DVI source is not present) • Firmware upgrade via RS-232 • RS-232 control • IP control • IR remote control • Supports USB 2.0 with backwa ...

  • Gefen EXT-DPKVM-841 - page 7

    4 FRONT P ANEL LA YOUT Front Panel 4 2 1 3 ...

  • Gefen EXT-DPKVM-841 - page 8

    5 FRONT P ANEL DESCRIPTIONS 1 Input Indicators (1 - 8) Each of these LED indicators glows bright blue according to the input selection (see Input Buttons , below) 2 IR Receives IR signals from the included IR Remote Control Unit. 3 Input Buttons (1 - 8) Pressing each of these buttons selects the desired input source (1 - 8). 4 Power This LED indica ...

  • Gefen EXT-DPKVM-841 - page 9

    6 BACK P ANEL LA YOUT Back Panel 5 2 8 9 6 7 3 4 1 10 ...

  • Gefen EXT-DPKVM-841 - page 10

    7 BACK P ANEL DESCRIPTIONS 1 5V DC Connect the included 5V DC locking power supply to this receptacle. 2 In 1 - In 8 Each of these ports will accept a standard DisplayPort source device. 3 Ext IR Connect an IR extender cable to this port. 4 USB Out (1 - 2) Connect USB devices (e.g. mouse devices, keyboards, etc.) to these ports. 5 Ethernet Use an E ...

  • Gefen EXT-DPKVM-841 - page 11

    IR REMOTE CONTROL UNIT 8 2 1 Activity Indicator This LED will be activated momentarily each time a button is pressed. 2 Source Selection Buttons (1 - 8) These buttons are used to select which source is routed to a monitor . Layout and Description 1 NOTE: An Activity Indictor that fl ashes quickly while holding down any one of the eight buttons ind ...

  • Gefen EXT-DPKVM-841 - page 12

    IR REMOTE CONTROL UNIT 9 Installing the Battery 1. Remove the battery cover on the back of the IR Remote Control Unit. 2. Insert the included battery into the open battery slot. The positive (+) side of the battery should be facing up. 3. Replace the battery cover . The Remote Control unit ships with two batteries. One battery is required for opera ...

  • Gefen EXT-DPKVM-841 - page 13

    IR REMOTE CONTROL UNIT 10 Corresponding DIP Switch Settings for each IR Channel It is important that the IR channel on the Remote Control unit, matches the IR channel set on the 8x1 DPKVM Switcher . For example, if both DIP switches on the IR Remote Control unit are set to IR channel 0 (both DIP switches down), then the 8x1 DPKVM Switcher must also ...

  • Gefen EXT-DPKVM-841 - page 14

    CONNECTING THE 8X1 DPKVM SWITCHER 11 How to Connect the 8x1 DPKVM Switcher 1 Connect up to eight (8) DisplayPort source devices to the DisplayPort inputs on the back panel of the Switcher using DisplayPort cables. 2 Connect a DisplayPort-supported display to the DisplayPort output on the back panel of the Switcher . a OPTIONAL: T o use the RS-232 c ...

  • Gefen EXT-DPKVM-841 - page 15

    OPERA TING THE 8X1 DPKVM SWITCHER 12 Front Panel Buttons and LED Indicators The front panel of the 8x1 DPKVM Switcher has a set of eight (8) LED indicators, displaying which input (source) is being displayed. Each of these LED indicators corresponds to one of the push-buttons on the front panel. Switching sources using the front-panel buttons Examp ...

  • Gefen EXT-DPKVM-841 - page 16

    13 OPERA TING THE 8X1 DPKVM SWITCHER Switching sources using RS-232 Con fi gure the Switch for use with RS-232 (see page 14 for details). Example: Switch to input 4 using RS-232 1 Use the command r 4 to route the Switcher to Input 4. See page 15 for important information on RS-232 commands. RS-232 commands are case-sensitive. 2 The LED indicator f ...

  • Gefen EXT-DPKVM-841 - page 17

    RS-232 CONTROL 14 Only pins 2 (Receive), 3 (T ransmit), and 5 (Ground) are used for communication. A null-modem adapter should not be used with this product. 54321 9876 12345 6789 Only Pins 2 (RX), 3 (TX), and 5 (Ground) are used on the RS-232 serial interface Serial Port Settings Bits per second .................................................... ...

  • Gefen EXT-DPKVM-841 - page 18

    RS-232 COMMANDS 15 Command Syntax All RS-232 commands are case-sensitive and must be entered in lowercase. Each command must be preceded by the ‘#’ character . A carriage return must also be appended to every command. Example : #set_http_port 80 [CR] IP Con fi guration Command Description #get_pass Prompts for the T elnet password #get_user_na ...

  • Gefen EXT-DPKVM-841 - page 19

    16 RS-232 COMMANDS #GET_USER_NAME Command The #GET_USER_NAME command prompts for the T elnet username. Syntax: #get_user_name Parameters: None #IPCONFIG Command The #IPCONFIG command displays all TCP/IP settings. Syntax: #ipcon fi g Parameters: None #RSTIP Command The #RSTIP command resets the IP con fi guration to the default settings. Syntax: # ...

  • Gefen EXT-DPKVM-841 - page 20

    17 RS-232 COMMANDS #SET_HTTP_PORT Command The #SET_HTTP_PORT command sets the Web server listening port. Syntax: #set_http_port param1 Parameters: param1 Port [0 - 255] #SET_P ASS Command The #SET_P ASS command sets T elnet password. Syntax: #set_pass param1 Parameters: param1 String Notes: The maximum length of the password string is 20 characters ...

  • Gefen EXT-DPKVM-841 - page 21

    18 RS-232 COMMANDS #SET_USER_NAME Command The #SET_USER_NAME command sets the T elnet user name. Syntax: #set_user_name param1 Parameters: param1 String Notes: The maximum length of the username string is 20 characters. #SGA TEW A Y Command Speci fi es the new IP gateway . Dot-decimal notation must be used when specify- ing the IP address. A reboo ...

  • Gefen EXT-DPKVM-841 - page 22

    19 RS-232 COMMANDS #SIP ADD Command The #SIP ADD command speci fi es a new IP address. Dot-decimal notation must be used when specifying the IP address. A reboot is required after the new IP address is set. Syntax: #sipadd param1.param2.param3.param4 Parameters: param1 IP address [0 - 255] param2 IP address [0 - 255] param3 IP address [0 - 255] pa ...

  • Gefen EXT-DPKVM-841 - page 23

    20 RS-232 COMMANDS #USE_TELNET_P ASS Command The #USE_TELNET_P ASS command enables / disabled the use of a T elnet password during the login process. Syntax: #use_telnet_pass param1 Parameters: param1 State [0 - 1] V alue Meaning 0 Disable password 1 Enable password General Commands Command Description #activebolo Activates the bootloader #fadefaul ...

  • Gefen EXT-DPKVM-841 - page 24

    21 RS-232 COMMANDS #F ADEF AUL T Function The #F ADEF AUL T function will reset the Switcher to the default routing settings. Syntax: #fadefault Parameters: None #IRRMT ADD Command The #IRRMT ADD sets the IR channel. The IR channel for the Switcher and the IR Remote Control Unit must be the same. Syntax: #irrmtadd param1 Parameters: param1 State [0 ...

  • Gefen EXT-DPKVM-841 - page 25

    22 RS-232 COMMANDS #LOCKPOWER Command The #LOCKPOWER enables/disables the power lock state. Enabling this feature will store the 5V status for each input prior to shutting the unit down. This preserves the 5V state when the unit is restarted. Syntax: #lockpower param1 Parameters: param1 State [0 - 1] V alue Meaning 0 Disable Power Lock 1 Enable Pow ...

  • Gefen EXT-DPKVM-841 - page 26

    23 Routing Commands The following command does not require the ‘#’ character . A carriage return must be added to the end of the command. Command Description R Routing command R Command The R command switches to the speci fi ed input. Syntax: r param1 Parameters: param1 DisplayPort Input [1 - 4] RS-232 COMMANDS ...

  • Gefen EXT-DPKVM-841 - page 27

    24 TELNET CONTROL The Gefen 8x1 DPKVM Switcher supports T elnet for controlling the Switcher over a network. T o access this feature, an IP address, subnet, gateway , and port numbers need to be set correctly . Consult the network administrator to obtain the proper IP address and settings for this product to properly communicate with the Switcher o ...

  • Gefen EXT-DPKVM-841 - page 28

    25 TELNET CONTROL 5. Use the #sipadd command to set the IP address for the Switcher . Check with a network administrator to obtain an available address, if necessary . DHCP is not supported by this Switcher . #sipadd 192.168.2.234 New IP set to: 192.168.2.234 After setting the IP address, power-cycle the Switcher for the changes to take effect. 6 S ...

  • Gefen EXT-DPKVM-841 - page 29

    26 FIRMW ARE UPDA TE Firmware Update Procedure Any terminal emulation program can be used to perform the upgrade process. The instructions below is outlined for Windows® HyperT erminal. 1. Connect an RS-232 cable between the Switcher and the computer running the terminal program. V erify the correct serial port settings (see page 14). 2. T ype the ...

  • Gefen EXT-DPKVM-841 - page 30

    27 RACK EAR INST ALLA TION Installing the Rack Ears Rack mount ears are provided for installation of this unit into a 1U rack mount space. 1. Locate the side screws on the unit. 2. Remove the front 2 screws that are located closest to the front of the unit. 3. Using the removed screws, screw the rack mounting bracket into the unit. 4. Repeat the pr ...

  • Gefen EXT-DPKVM-841 - page 31

    28 SPECIFICA TIONS Maximum Pixel Clock................................................................................360 MHz Video Input Connectors.......................................................(8) DisplayPort, female Video Output Connector ......................................................(1) DisplayPort, female USB Input Connectors.. ...

  • Gefen EXT-DPKVM-841 - page 32

    29 W ARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is noti fi ed within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanica ...

  • Gefen EXT-DPKVM-841 - page 33

    Rev A3 Pb This product uses UL listed power supplies. 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www .gefen.com support@gefen.com ...

Fabricante Gefen Categoría Switch

Los documentos del dispositivo Gefen EXT-DPKVM-841 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Gefen
- manuales de instrucciones EXT-DPKVM-841
- hojas de producto Gefen
- folletos informativos
- o etiquetas energéticas Gefen EXT-DPKVM-841
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Gefen EXT-DPKVM-841.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Gefen EXT-DPKVM-841, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Gefen EXT-DPKVM-841. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Gefen EXT-DPKVM-841.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Gefen EXT-DPKVM-841, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Gefen EXT-DPKVM-841. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Gefen EXT-DPKVM-841.

El manual de instrucciones completo de Gefen debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Gefen EXT-DPKVM-841 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Gefen EXT-DPKVM-841, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Gefen EXT-DPKVM-841 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Gefen EXT-DPKVM-841 - que deben facilitarnos los primeros pasos durante el uso de Gefen EXT-DPKVM-841
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Gefen EXT-DPKVM-841
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Gefen EXT-DPKVM-841 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Gefen EXT-DPKVM-841?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Gefen EXT-DPKVM-841, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Gefen EXT-DPKVM-841 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)