-
Oreck WS-7013U - page 1
WS-7013U Wi r eless 433 MHz T emperatur e Station Instruction Manual Register your product on the web at: WWW .ORECK.COM ...
-
Oreck WS-7013U - page 2
T ABLE OF CONTENTS T opic Page Inventory of Contents 2 Quick Setup 3-5 Detailed Setup Guide Battery Installation 5-7 Setting the T ime 7-8 Selecting Units of Measurement 8 Features Minimum and Maximum T emperatures 9 Resetting Minimum and Maximum T emperatures 9 Mounting 9-10 T roubleshooting 10-12 Maintenance and Care 12 Specifications 13-14 W arr ...
-
Oreck WS-7013U - page 3
INVENTOR Y OF CONTENTS 1. The indoor temperature station (Figure 1) 2. The remote temperature sensor (TX6U) and mounting bracket (Figure 2) 3. (3) 1/2" Philips screws 4. One strip of double sided adhesive tape 5. Instruction Manual and W arranty Card 6. (2) AAA 1.5V batteries 7. (2) AAA 1.5V batteries ADDITIONAL EQUIPMENT 1. Philips screwdrive ...
-
Oreck WS-7013U - page 4
QUICK SETUP Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries should be out of both units for 10 minutes. 3. Place the batteries into the r emote temperatur e sensor first then into the indoor temperature station. (All remo ...
-
Oreck WS-7013U - page 5
Any walls the signal will have to pass through will reduce distance. An outdoor wall or window will have 20 to 30 feet of resistance and an interior wall will have 10 to 20 feet of resistance. Y our distance plus resistance should not exceed 80 feet in a straight line. NOTE: Fog and mist will not harm your remote temperature sensor, but direct rain ...
-
Oreck WS-7013U - page 6
3. The hour will now be flashing. a. Press and release the " MIN/MAX " button until the correct hour is shown. Note: When in the 12h mode "PM" is displayed under the word "TIME" during PM hours. During the AM hours this area will be blank. b. When the correct hour is shown, press and release the "SET" button ...
-
Oreck WS-7013U - page 7
B. INDOOR TEMPERA TURE ST A TION Note: After the batteries are installed, DO NOT press any buttons. This may interfere with the signals, causing temperatures to register incorrectly . 1. Remove the battery cover on the backside. To do this, push the cover upward and pull it out. 2. Observing the correct polarity , install (2) AAA batteries. 3. Repl ...
-
Oreck WS-7013U - page 8
5. The indoor temperature station should now show: "-:- -" in the TIME LCD, and temperatures in the INDOOR and OUTDOOR LCD’ s. II. TIME A. SETTING THE TIME 1. Press and hold the " SET " button for 5 seconds, "12h" will appear in the TIME LCD. 2. Press and release the " MIN/MAX " button to select either 12h ...
-
Oreck WS-7013U - page 9
4. Press and release the " MIN/MAX " button to set the hour . 5. Press and release the " SET " button to move to the minute setting. 6. Press and release the " MIN/MAX " button to set the minutes. 7. Press and release the " SET " button to activate the clock. Note: When in 12h mode, there is only a "PM&q ...
-
Oreck WS-7013U - page 10
IV . FEA TURES A. MINIMUM AND MAXIMUM TEMPERA TURES 1. Press and release the " MIN/MAX " button. "MIN" appears in the temperature LCDs and the recorded minimum temperatures are displayed. 2. Press and release the " MIN/MAX " button to toggle to the maximum temperatures. The time of occurrence of the value for outdoor t ...
-
Oreck WS-7013U - page 11
before permanently mounting. A. REMOTE TEMPERA TURE SENSOR 1. Remove the mounting bracket from the remote temperature sensor . 2. Mount using either screws or adhesive tape. 3. Reattach the remote temperature sensor to the mounting bracket. B. THE TEMPERA TURE ST A TION 1. The indoor temperature station comes with the table stand already mounted. I ...
-
Oreck WS-7013U - page 12
Problem: The LCD is faint Solution: Replace batteries Problem: No outdoor temperature is displayed. Solution: 1) Remove all batteries, reinsert into remote temperature sensor first, and then into the indoor temperature station. 2) Place remote temperature sensor closer to the indoor temperature station. 3) Make sure all batteries are new . 4) Place ...
-
Oreck WS-7013U - page 13
responsive to ambient air currents because of the shielding effect of the display case. In addition, the case can act as a heat sink to absorb and store heat from external sources (i.e. handling of the case or radiant heat). In addition, the much greater range of the outdoor temperature sensor requires a different calibration curve than the indoor ...
-
Oreck WS-7013U - page 14
SPECIFICA TIONS T ransmitting 433MHz Frequency Measuring T emperatur es Indoor T emperature 32°F to 156.2°F with Station: Indoor 0.2°F resolution. (0°C to 69.0°C with 0.1°C resolution) Remote T emperature -21.8 °F to 156.2°F Sensor: Outdoor 0.2°F resolution. (-29.9° C to 69.0° C with 0.1°C resolution) T emp accuracy +/- 1°F (+/- .5°C) ...
-
Oreck WS-7013U - page 15
Remote T emperature 1.57" x 0.9" x 5.04" Sensor (40 x 23 x 128 mm) Battery life Approximately 1 year W ARRANTY INFORMA TION Oreck Corporation warrants the Indoor/Outdoor Clock and W eather Station (WS-7013U) free from defects in material and workmanship under normal, non-commercial use and service. Oreck will remedy any such defects ...
-
Oreck WS-7013U - page 16
©2002 Oreck Holdings, LLC. All rights reserved. ...
¿Tienes una pregunta acerca de Oreck WS-7013U?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Oreck WS-7013U, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Oreck WS-7013U probablemente compartirá una forma de solucionarlo.