-
Airlink101 AWLC4030 - page 1
Super G™ Cardbus Adapter Model # AWLC4030 User’s Manual Ver. 2B ...
-
Airlink101 AWLC4030 - page 2
2 Table of Contents 1. Introduction ................................................................................................................................. 3 1.1 Package Contents ........................................................................................................... ....... 3 2. Installation............................ ...
-
Airlink101 AWLC4030 - page 3
3 1. Introduction Thank you for purchasing the Super G™ Cardbus Adapter. When used with other Airlink101™ Super G™ wireless products, the wireless data throughput increases compared to the standard 802.11g products. This Adapter supports 64/128-bit WEP data enc ryption that protects your wireless network from eavesdropping. It also supports W ...
-
Airlink101 AWLC4030 - page 4
4 2. Inst allation 2.1 Install Driver & Utility This section provides instructions on how to install the Super G™ Cardbus Adapter . The driver is install ed along with the utility. Note: Do not insert the Cardbus Adapter until you have reached the appointed step. For Windows 98SE and ME users, you may be prompted to insert the Windows 98SE or ...
-
Airlink101 AWLC4030 - page 5
5 Step 2 Click Next at the welcome screen. Step 3 Click Next to accept the default destination folder. ...
-
Airlink101 AWLC4030 - page 6
6 Step 4 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click Yes at the Digital Signatur e Not Found prompt). Step 5 Verify Yes, I want to restart my computer now is selected and click Finish to restart your computer. ...
-
Airlink101 AWLC4030 - page 7
7 Step 6 After your computer is restar ted, insert the Cardbus Adapter. Step 7 Select Install the software automatically and click Next . For Windows 98SE and ME, select Search for the best dr iver for your device and click Next . Verify all the check boxes are checked and click Next . ...
-
Airlink101 AWLC4030 - page 8
8 Step 8 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click Yes at the Digital Signatur e Not Found prompt). Step 9 Click Finish . (Restart the computer for Windows 98SE and ME). ...
-
Airlink101 AWLC4030 - page 9
9 2.2 Verify Driver Installation To verify if the driver has been installed successfully, pl ease perform the following steps. Step 1 Right-click on My C omputer from your desktop and select Properties . Step 2 Select the Device Manager tab. (For Windows 2000/XP, select the Hardware tab first then click on Device Manager ). ...
-
Airlink101 AWLC4030 - page 10
10 Step 3 Expand Network adapters from the list and verify that Airlink101 MIMO XR Cardbus Adapter is listed and no yellow question mark is beside it. If Airlink101 Super G Cardbus Adapter is not listed, or y ou see a yellow question mark beside it, please re-install the driver again. ...
-
Airlink101 AWLC4030 - page 11
11 3. Configure the Cardbus Adapter This section describes how to connect your Super G™ Cardbus Adapter to a wireless network. Note to Windows XP Users: You must disable the Wireless Zero Configur ation Utility in order to use the bundled Wireless Utility. Please follow the steps below to disable XP’s wireless utility. Step 1 Double-click on th ...
-
Airlink101 AWLC4030 - page 12
12 To open the Cardbus Adapter’s utility go to Start > (All) Program s > Airlink101 Super G Cardbus Utility > Airlink101 Super G Cardbus Utility . Step 1 Go to the AP List tab, select the SSID (Network Name) of the wireless network you wish to connect to, and click Connect . ...
-
Airlink101 AWLC4030 - page 13
13 Step 2 If encryption is not enabled for the select ed access point / router, skip to step 6. Otherwise, enter a Profile Name for your wireless setting and click Next . Step 3 Verify that the Network Name matches the SSID of your wireless network and click Next . ...
-
Airlink101 AWLC4030 - page 14
14 Step 4 Select the proper encryption setting for your wireless router or access point from the drop-down menu and click Next . Step 5 Follow the on-screen instructions to complete the encryption settings. Click Complete when finished. Step 6 You should see a blue circle around the antenna icon indicating a valid connection. ...
-
Airlink101 AWLC4030 - page 15
15 Step 7 Go to the Link Information tab and click on the More button. Step 8 Verify that you are receiving adequate Signal Strength and Link Quality and that you have been assigned a valid IP address (instead of all 0’s). If you do not have adequate Signal Strength, tr y re-orienting the Access Point and/or the Cardbus Adapter to get a better re ...
-
Airlink101 AWLC4030 - page 16
16 4. Configure the Wireless Utility This section describes the various functi ons of the Wireless Utility that you can configure, including the setti ngs of wireless encryption. 4.1 Link Information The Link Information tab shows the current profile in use as well as details of the current network connection. Click on the More button to see the de ...
-
Airlink101 AWLC4030 - page 17
17 The Wireless Information displays the current wireless network you are connected to as well as various other statuses such as the Signal Strength and your assigned IP address. ...
-
Airlink101 AWLC4030 - page 18
18 4.2 AP List The AP List tab displays all the available Acce ss Points detected by the Cardbus Adapter. Simply select the desired Access Point you wish to connect to and click Connect . The Site Information displays a list of status for the selected AP, including the Channel number and the Encryption status. ...
-
Airlink101 AWLC4030 - page 19
19 4.3 Configure Encryption Settings This section describes how to configure encryption settings for the Cardbus Adapter . Note: The encryption settings you set for the A dapter must match t he same settings of the Access Point/Wireless Router; otherwise, the encryption will not work properly. Step 1 From the AP List tab, select the Access Point/W ...
-
Airlink101 AWLC4030 - page 20
20 Step 3 Verify the Network Name (SSID) is correct and click Next . For WEP Settings: WEP Step 4 Select the appropriate Authentication Mode and Encryption settings and click Next . ...
-
Airlink101 AWLC4030 - page 21
21 WEP Step 5 Select the appropriate Input Method , Key (password), Key Index , and click Next . WEP Step 6 Click Complete to finish the settings. ...
-
Airlink101 AWLC4030 - page 22
22 For WPA Settings: WPA Step 4 Select WPA-PSK and the appropriate Input Method and click Next . WPA Step 5 Enter the WPA Key (passphrase) and click Next . ...
-
Airlink101 AWLC4030 - page 23
23 WPA Step 6 Click Complete to finish the settings. Step 7 You should see a blue circle around the antenna icon indicating a valid connection. A lock icon beside the antenna indicates the connection is encrypted. ...
-
Airlink101 AWLC4030 - page 24
24 4.4 Profile Setting The Profile Setting tab lists all the profiles you have created. You can create new profiles for different network environments. To add a new profile, follow the steps below: Step 1 Click on the Add button. ...
-
Airlink101 AWLC4030 - page 25
25 Step 2 Enter a name for your new profile and click Next . Step 3 Enter the SSID (Network Name) of the wireless network you want to connect to and click Next . ...
-
Airlink101 AWLC4030 - page 26
26 Step 4 Configure any encryption setting if required and click Next . Step 5 Click Complete to finish the profile setting. ...
-
Airlink101 AWLC4030 - page 27
27 Step 6 Your new profile will be listed in the Profile List. Step 7 You can quickly select which prof ile you want to use from the Link Information tab depending on your network environments wit hout having to reconfigure the settings each time. ...
-
Airlink101 AWLC4030 - page 28
28 4.5 Static IP Setting To change the IP address of the wireless adapter to Static IP, follow the steps below: Step 1 On the last step of 4.4 Profile Setting , under IP setting, select New Setting and click Next . Step 2 Select Static . Step 3 Enter in the information and click Complete to finish the setting. ...
-
Airlink101 AWLC4030 - page 29
29 4.6 About The About tab shows the Utility, Driver, and Firmware version as well as the MAC address of the Super G™ Cardbus Adapter . ...
-
Airlink101 AWLC4030 - page 30
30 T echnical Support E-mail: support@airlink101.com Toll Free: 1-888-746-3238 Web Site: www.airlink101.com *Super G TM technology (108 Mbps) can only be obtained when using products with A theros Super G TM chipset *Theoretical maximum wireless signal rate based on IEEE standard 802.11g specifications. Actual data throughput will vary. Network con ...
¿Tienes una pregunta acerca de Airlink101 AWLC4030?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Airlink101 AWLC4030, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Airlink101 AWLC4030 probablemente compartirá una forma de solucionarlo.