-
Makita 601D - page 1
Battery-Powered Driver Drill Steel / Wood 10 mm (318") Equipped with Electric Brake 10 mm (3/8") MODEL 601D 10 mm (3/8") MODEL 6OlDST With Battery & Charger Wood screw (RPM) (L x W x H) weight 0.7 kg (311 6" x 3/4"1 - 750 (7-13116" x 1-13/16" x 6-5/32") (1.5 lbs) 4.5 mm x 20 mm 198 mm x 46 mm x 156 mm INS ...
-
Makita 601D - page 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invite in ...
-
Makita 601D - page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords i ...
-
Makita 601D - page 4
IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY & CHARGER Length of Cord (Feet) 25 AWG Size of Cord 18 I. SAVE THESE INSTRUCTIONS - This manual 50 100 150 18 18 16 9. Do not operate charger with damaged cord or plug - replace them im- mediately. IO. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; ...
-
Makita 601D - page 5
ADDITIONAL SAFETY RULES FOR BATTERY 1. Always charge the Makita battery 122 immediately after purchase. 2. Always recharge the Makita battery 122 after use. 3. Be sure to charge the Makita battery 122 for approx. one week every six months, when not using it for long periods. If left uncharged, it may become unchargeable. 4. Use only the Makita char ...
-
Makita 601D - page 6
ADDITIONAL SAFETY RULES FOR CHARGER 1. The Makita charger Model DC122 is specifically designed to charge only the Makita battery 121 or 122. Do not attempt to charge any other battery with this charger. 2. Handle the charger carefully. Do not drop or strike it. 3. Never carry the charger by cord or yank it to disconnect from receptacle. 4. Keep cor ...
-
Makita 601D - page 7
ADDITIONAL SAFETY RULES FOR TOOL 1. This tool is specifically designed to drill in woods/metals or to drive wood 2. Always be sure you have a firm footing. 3. Always secure small workpieces in a vise or similar hold-down device. 4. Hold the tool firmly. 5. Keep hands away from rotating parts. 6. When drilling into walls, floors or wherever "li ...
-
Makita 601D - page 8
Charging Connect the battery to the charger using the adaptor cord. Then plug the charger into the power source. The charging light will illuminate and charging will begin. When the charg- ing light goes out at a certain time, the charging is complete. Unplug the charger. (Note: Refer to the table below for the charging time.) DC122 DC121 122 3 A ...
-
Makita 601D - page 9
Installing or removing the drill bit CAUTION : Always be sure that the tool is switched off and the batterv is disconnected from the tool before installing or removing the bit. To install the bit, place it in the chuck as far as it will go. Tighten the chuck by hand. Place the chuck key in each of the three holes and tighten clockwise. Be sure to t ...
-
Makita 601D - page 10
Connecting the battery to the tool Connect the battery to the tool using the adaptor cord. To prevent the adaptor cord from being accidentally disconnected, hook the cord to the strain relief hook on the battery. Carrying the battery Hook the battery to your waist belt. If the adaptor cord is too long for your work, use the band provided to hold it ...
-
Makita 601D - page 11
Screwdriving operation Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed gradually. Release the switch trigger just as the screw bottoms out. The electric brake will then stop the tool immediately, preventing the screw and/or bit from being damaged. When driving woo ...
-
Makita 601D - page 12
MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery is disconnected from the tool before attempting to perform inspection or maintenance. Storage Do not clean the tool, charger and/or battery with benzine, thinner or cleaning chemi- 0 Do not store the tool, charger and/or battery in locations where the temperature may ...
-
Makita 601D - page 13
Dec -19-’94 US 10 mm (3/8”) Model 601D BATTERY-POWERED DRIVER DRILL Note: The switch and other part configurations may differ from country to country. 13 ...
-
Makita 601D - page 14
1 1 Name Plate 10 2 5 Tapping Screw 4x20 11 12 3 1 Housing Set IWith Item 181 14 5 1 Lever 15 6 1 Trigger 7 1 Inlet 16 8 1 Motor I0.C. 12 V 1 11 9 1 Plane Bsarlng 5 18 4 1 Switch 13 14 1 Gear Complete 1 Drill Chuck S10 1 Plane Besrlng 4 1 Gear COmplete 1 1-46 1 Plane Beering 4 1 Holder 1 1 Makita Label 1 Tapping Screw BT 3x 10 Housing Set IWith Ite ...
-
Makita 601D - page 15
Recycling the battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. To recycle the battery: 1) Remove belt from the battery 2) Ship or take battery to your nearest Makita Factory Service Center or Distributor that sells Makita lead batteries. (Call your nearest Makita Service Center or ...
¿Tienes una pregunta acerca de Makita 601D?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 601D, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 601D probablemente compartirá una forma de solucionarlo.