-
PYLE Audio 100 - page 1
Router Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e refer ence. Model No. ______________________________________ T ype ___________________________________________ Serial No. _______________________________________ IMPORT ANT Please make ...
-
PYLE Audio 100 - page 2
2 Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could result in serious injury and pr operty damage. There ...
-
PYLE Audio 100 - page 3
3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer , birth defects or other reproductive harm. Some examples of these chemicals are: ● lead from lead-based paints ● crystalline silica from bricks and cement and other masonry pr ...
-
PYLE Audio 100 - page 4
4 Read all instructions. Failure to follow all instructions listed below may result in electric shock, fir e and/or serious injury . The term "power tool" in all of the war nings listed below refers to your mains-operated (cor ded) power tool or battery-operated (cordless) power tool. SA VE THESE INSTRUCTIONS 1) W ork area safety a) Keep ...
-
PYLE Audio 100 - page 5
5 d) Remove any adjusting key or wrench befor e tur ning the power tool on. A wrench or a key left attached to a r otating part of the power tool may result in personal injury . e) Do not overreach. Keep pr oper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress pr operly . Do not wear ...
-
PYLE Audio 100 - page 6
6 1. HOLD POWER TOOL BY INSULA TED GRIPPING SURF ACES WHEN PERFORMING AN OPERA TION WHERE THE CUTTING TOOL MA Y CONT ACT HIDDEN WIRING OR ITS OWN CORD. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator . 2. USE CLAMPS OR OTHER PRACTICAL WA Y TO SECURE AND SUPPORT THEWORKPIECE TO A ...
-
PYLE Audio 100 - page 7
7 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ........................ microfarads l ........................ litres g ........................ grams kg ........... ...
-
PYLE Audio 100 - page 8
8 EXTENSION CORD SELECTION If an extension cord is used, make sur e the conductor size is lar ge enough to prevent excessive voltage dr op which will cause loss of power and possible motor damage. A table of recommended extension cor d sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 23 ...
-
PYLE Audio 100 - page 9
9 FOREWORD The router is one of the most useful tools in the woodworking field. It may be used for many cutting and shaping operations such as slotting, mortising, dadoing, grooving, rabbeting, corner -rounding, beading, dovetailing, veining, inlay work, etc. FUNCTIONAL DESCRIPTION SELECTING THE BIT This Router comes with a 1 / 4 " split type ...
-
PYLE Audio 100 - page 10
10 1. T o remove motor unit from base unit: Open the clamp (A) Fig. 1. While holding base, turn power unit COUNTERCLOCKWISE until lower pin (B) in motor housing is disengaged from gr oove in base. Lift power unit free fr om base unit. 2. Clean and insert shank of bit into collet until shank bottoms, then back it out approximately 1/16". Do not ...
-
PYLE Audio 100 - page 11
11 NOTE: Setting the index line to 1/4" on the ring means the cutting edge of the bit is exposed 1/4" below the base. CONNECTING TO POWER SOURCE Before connecting tool to power sour ce AL WA YS MAKE SURE SWITCH IS IN THE “OFF” POSITION. Also check that the power circuit is the same as that shown on specification plate of the router . ...
-
PYLE Audio 100 - page 12
12 USING THE ROUTER IMPORT ANT : Before using your router , consider the kind and total amount of material to be removed. Depending on the workpiece, mor e than one cut may be necessary to avoid overloading the motor . Before beginning the cut on the actual workpiece, make a sample cut on a piece of scrap lumber to show exactly how the cut will loo ...
-
PYLE Audio 100 - page 13
13 TEMPLET GUIDES A wide variety of templet guides is available for use in pattern and templet routing operations. Fig. 7 shows a typical combination bit, templet guide, and locknut. DISCONNECT TOOL FROM POWER SOURCE. T o install, insert templet guide in center hole of router base and secure in place with the locknut. BEFORE CONNECTING TOOL TO POWE ...
-
PYLE Audio 100 - page 14
14 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air . All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed air . F AILURE TO ST ART Should your tool fail ...
-
PYLE Audio 100 - page 15
15 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter -Cable warrants its Professional Power T ools for a period of one year from the date of original purchase. W e will repair or replace at our option, any part or parts of the pr oduct and accessories covered under this warranty which, after examination, proves to be defective in workmanship or materia ...
-
PYLE Audio 100 - page 16
16 NOTES ...
-
PYLE Audio 100 - page 17
The following are trademarks of PORTER-CABLE • DEL T A (Las siguientes son marcas registradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T AC ...
¿Tienes una pregunta acerca de PYLE Audio 100?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con PYLE Audio 100, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con PYLE Audio 100 probablemente compartirá una forma de solucionarlo.