-
Chamberlain Series 1200 - page 1
Garage Door Opener For Residential Use Only (Model Series 1200 - Canada ) Model 1260 - 1/2HP Model 1250 - 1/3HP Model 1255 - 1/2HP Model 1245 - 1/3HP ® Owner's Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLO ...
-
Chamberlain Series 1200 - page 2
Start by reviewing these important safety alert symbols 2 CONTENTS PAGE A review of safety alert symbols ...............................2 You'll need tools ........................................................3 Safety information regarding garage door locks and ropes ...............................................................3 Testing y ...
-
Chamberlain Series 1200 - page 3
Pliers Wire Cutters Claw Hammer Hack Saw Screwdriver Adjustable End Wrench 1/2" and 7/16" Sockets and Wrench Drill Tape Measure 2 1 Stepladder Pencil 3/16", 5/16" and 5/32" Drill Bits Carpenter's Level Y ou'll Need T ools During assembly , installation and adjustment of the opener , instructions will call for hand ...
-
Chamberlain Series 1200 - page 4
4 Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.). See page 20 for details. Support bracket & fastening hardware is required. See page 13. — — — — — — — — Door Center Header Wall Safety Reversing Sensor Floor must be ...
-
Chamberlain Series 1200 - page 5
5 Straight Door Arm Section Door Bracket Plate Door Bracket Curved Door Arm Section Safety Labels and Literature Header Bracket UP CEILING MOUNT ONLY Safety Reversing Sensor Mounting Bracket With Square Holes (2) "C" Wrap (2) Safety Reversing Sensor Mounting Bracket With Slot (2) Sprocket Cover 2 Conductor Bell Wire White & White/Red? ...
-
Chamberlain Series 1200 - page 6
Assembly Step 1 Attach the T -rail to the Opener To fasten rail, use only those screws mounted in top of the opener. Failure to do so will cause serious damage to the opener. 6 USE ONLY THIS TYPE AND SIZE SCREW Washered Screw 5/16"-18x1/2" Styrofoam Chain T-rail Hole Assembly Step 2 Attach Chain to Sprocket and Install Sprocket Cover • ...
-
Chamberlain Series 1200 - page 7
Assembly Step 3 Tighten the Chain 7 IMPORT ANT INST ALLA TION INSTRUCTIONS T o reduce the risk of severe injury or death to persons: 1. READ AND FOLLOW ALL INST ALLA TION INSTRUCTIONS. 2. Install only on a properly balanced and lubricated garage door. An improperly balanced door may not reverse and could result in severe injury or death. Repairs to ...
-
Chamberlain Series 1200 - page 8
• Open your door to the highest point of travel as shown. Draw an intersecting horizontal line on the header wall 2" above the high point. This height will provide travel clearance for the top edge of the door. Header Wall Ceiling Track Highest Point of Travel Door 2" 8 Proceed to Step 2, page 10. Door Track Header Wall Highest Point of ...
-
Chamberlain Series 1200 - page 9
9 Header Wall Vertical Centerline Vertical Centerline of Garage Door 2x4 Unfinished Ceiling Structural Supports 2x4 OPTIONAL CEILING MOUNT FOR HEADER BRACKET • Close the door and mark the inside vertical centerline of your garage door. Extend the line onto the header wall above door. If headroom clearance is minimal, you can install the header br ...
-
Chamberlain Series 1200 - page 10
UP Lag Screws 5/16"x18x1-7/8" Garage Door Vertical Center Line Header Wall Finished Ceiling Header Bracket 6" Maximum Vertical Center Line Door Spring Lag Screws 5/16"x18x1-7/8" Highest Point of Travel (of Garage Door) Vertical Center Line Header Wall Garage Door UP CEILING MOUNT ...
-
Chamberlain Series 1200 - page 11
Header Bracket Chain Pulley Bracket Temporary Support Header Wall Garage Door T-rail Clevis Pin 5/16"x2-3/4 " Ring Fastener Header Bracket Chain Pulley Bracket T-rail • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. If the door spring is in the way you'll need help. Have ...
-
Chamberlain Series 1200 - page 12
Installation Step 4 Position the Opener Follow instructions which apply to your door type as illustrated. To prevent damage to steel, aluminum, fiberglass or glass panel doors, do not rest the opener on the door without using a 2x4. SECTIONAL Door & ONE-PIECE Door with T rack T-Rail 2x4 laid flat Door Stepladder ONE-PIECE Door without T rack ? ...
-
Chamberlain Series 1200 - page 13
Installation Step 5 Hang the Opener Two representative installations are shown. Yours may be different. Hanging brackets should be angled, Figure 1, to provide rigid support. On finished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener. The bracket and fastening hardware are not supplied. • Mea ...
-
Chamberlain Series 1200 - page 14
Installation Step 6 Install the Door Control 14 Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death. Install the Door Control (or any additional push buttons) out of the reach of children and away from all moving parts of the door and door hardware, b ...
-
Chamberlain Series 1200 - page 15
Lens Slot 75 Watt Max. Light Bulb Lens Tab Light Lens Screw Panel Install the light(s) • Install a 75 watt maximum light bulb in each socket. The light(s) will turn ON and remain lit for approximately 4-1/2 minutes when power is connected. Then the light(s) will turn OFF. • If the bulbs burn out prematurely due to vibration, replace with a &quo ...
-
Chamberlain Series 1200 - page 16
To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you have, contact a qualified electrician to install the proper outlet. Installation Step 9 Electrical Requirement Ground Tab Green Gro ...
-
Chamberlain Series 1200 - page 17
The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. This is a required safety device and cannot be disabled. Installation procedures are the same for sectional and one-piece doors. Without a properly working safety reversing sensor , persons (particularly children) could ...
-
Chamberlain Series 1200 - page 18
1/4x1-1/2" Lag Screw #10-32x3/8" Screw 1/4"-20 Lock Nut #10x32 Lock Nut Staples 1/4"-20x1/2" Carriage Bolts Installation Step 10 Install the Safety Reversing Sensor Mounting Bracket With Square Holes #10-32x3/8" Screws "C" Wrap #10-32 Lock Nuts Mounting Bracket with Slot 1/ ...
-
Chamberlain Series 1200 - page 19
Invisible Light Beam Protection Area Sensor Sensor Connect Wire to Opener Terminals Bell Wire Bell Wire Finished Ceiling OPENER TERMINAL SCREWS Sensor Connections Wall Control Connections (dotted line) 1 2 3 • Center each sensor unit in a "C" wrap with lenses pointing toward each other across the door (see Figure 7). • Secure sensors ...
-
Chamberlain Series 1200 - page 20
Installation Step 1 1 Fasten Door Bracket Follow instructions which apply to your door type as illustrated below or on page 21. T o prevent damage to steel, aluminum, fiberglass or glass panel doors, always reinforce the inside of the door both vertically and horizontally with angle iron. A horizontal brace should be long enough to be secured to 2 ...
-
Chamberlain Series 1200 - page 21
Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, aluminum, steel, door with glass panel, etc.). Header Wall Vertical Centerline of Garage Door Finished Ceiling Header Bracket 2x4 Support Door Bracket Door Brkt 1-piece CAN Door Bracket Inside Edge of Door or Reinforcement Boa ...
-
Chamberlain Series 1200 - page 22
Installation Step 12 Connect Door Arm to T rolley Follow instructions which apply to your door type as illustrated below and on page 23. Make sure garage door is fully closed. Pull the manual release handle to disconnect the outer trolley from the inner trolley. Slide the outer trolley back (away from the door) about 2" as shown in Figures 1, ...
-
Chamberlain Series 1200 - page 23
All ONE-PIECE Doors Assemble the Door Arm: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • With the door closed, connect the straight door arm section to the door bracket with a clevis pin. • Secure with a ring fastener. Nuts 5/16"-18 Lock Washers 5/16" Ring ...
-
Chamberlain Series 1200 - page 24
Adjustment Step 1 Adjust the UP and DOWN Limits Do not make any limit adjustments until the safety reversing sensors are completely installed. 24 Limit adjustment settings regulate the points at which the door will stop when moving up or down. The door will stop in the up direction if anything interferes with door travel. The door will reverse in t ...
-
Chamberlain Series 1200 - page 25
Adjustment Step 2 Adjust the Force Too much force on the door will interfere with the proper operation of the safety reverse system. The door might not reverse properly when required and could seriously injure or kill someone under it. Do not increase the force beyond the minimum amount required to close the door. Do not use the force adjustments t ...
-
Chamberlain Series 1200 - page 26
Adjustment Step 4 T est the Safety Reverse System Test: • Place a 2x4 laid flat on the floor, centered under the garage door. • Operate the door in the down direction. The door must reverse on striking the obstruction. Adjustment: If the door stops on the obstruction, it is not traveling far enough in the down direction. • Increase the DOWN l ...
-
Chamberlain Series 1200 - page 27
The remote control transmitter: The opener must learn the code of any new remote control. Page 29 explains how to program your receiver and how to erase all codes if required. Self service of your radio controls and remote controls is not recommended. If service is needed, call the toll- free number listed on the back page. The remote control batte ...
-
Chamberlain Series 1200 - page 28
28 Operation of Y our Opener To open the door manually: The door should be fully closed if possible. Pull down on the red manual release handle and lift the door manually. To reconnect the door to the opener, press the Door Control button/push bar. Activate the opener with any of the following: • The Remote Control Transmitter. Hold push button d ...
-
Chamberlain Series 1200 - page 29
Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death. Do not allow children to operate the Door Control or remote control transmitter(s). A moving garage door could injure or kill someone under it. Activate the opener only when you can see the door cle ...
-
Chamberlain Series 1200 - page 30
1. Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light, check the fuse box or the circuit breaker. (Some outlets are controlled by a wall switch.) 2. Have you disabled all door locks? Review installation instruction warnings on page 7. 3. Is there a build-up of ice or snow under the door? The door may be froze ...
-
Chamberlain Series 1200 - page 31
The chain droops or sags: It is normal for the chain to droop slightly in the closed door position. Use the manual release rope and handle to disconnect the trolley. If the chain returns to the normal height when the trolley is disengaged and the door reverses on a 2x4 laid flat, no adjustments are needed. (See page 7.) 31 Having a Problem? (contin ...
-
Chamberlain Series 1200 - page 32
10 UP CEILING MOUNT ONLY 7 12 14 12VDC 3 LIGHT LOCK 1 2 4 5 NOTICE 6 9 8 11 13 15 16 2 1 3 4 5 RAIL GREASE NO. 83A4 6 Rail Assembly Parts Installation Parts 32 KEY PART NO. NO. DESCRIPTION 1 1A995 Master link kit 2 41A4813 Chain pulley bracket 3 41A3489 Complete trolley assembly 4 183B99 One-piece T-rail 5 41D3484 Full chain assembly 6 83A4 Rail gr ...
-
Chamberlain Series 1200 - page 33
Repair Parts Opener Assembly Parts 1 2 11 9 14 15 16 17 20 5 4 6 3 DN UP Brown Wire (Down) Contact LIMIT SWITCH ASSY. Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear 8 10 21 17 13 7 8 (1260, 1250) 19 7 (1260, 1250) (1255, 1245) (1260, 1250) (1255, 1245) 8 12 18 (1260, 1250) 3 KEY P ART NO. NO. DESCRIPTION 1 31D380 Sprocket cover ...
-
Chamberlain Series 1200 - page 34
1 2 3 4 5 6 7 8 9 0 ENTER LIGHT LOCK Model 58LMC Model 64LMC Model 99LMC Model 60LMC Multi-Function Mini Remote Control: With key ring & V elcro fastening strip. Keyless Entry: Enables homeowner to operate garage door opener from outside by entering code on specially designed keyboard. Outside Keylock: Operates the garage door automatically fro ...
-
Chamberlain Series 1200 - page 35
Index Access Door/Outside Quick Release Accessory ..........................................................................................4, 34 Electrical Safety Warnings ....................................................................................................................2, 7, 16, 27 Garage Door Testing for balance, binding and sti ...
-
Chamberlain Series 1200 - page 36
LIFT -MASTER SERVICE IS ON CALL OUR LARGE SERVICE ORGANIZATION SPANS AMERICA AND CANADA INSTALLATION AND SERVICE INFORMATION IS AS NEAR AS YOUR TELEPHONE SIX DAYS A WEEK. SIMPLY DIAL OUR TOLL FREE NUMBER: 1-800-654-4736 HOURS: (Mountain Std. Time) 6:00 A.M. TO 6:00 P.M. - Monday through Friday 7:00 A.M. TO 3:00 P.M. - Saturday Closed Sunday For pro ...
¿Tienes una pregunta acerca de Chamberlain Series 1200?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Chamberlain Series 1200, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Chamberlain Series 1200 probablemente compartirá una forma de solucionarlo.