Español dropdown-ico

Manual de instrucciones Hitachi EM 490

32 de páginas 0.62 mb
Descargar

Pasar a la página of 32

Summary
  • Hitachi EM 490 - page 1

    INSTRUCTIONS-P ARTS LIST 307–735 Rev G Supersedes F EM 490  PORT ABLE/ELECTRIC AIRLESS P AINT SPRA YER 2750 psi (190 bar) MAXIMUM WORKING PRESSURE Model 231–002, Series C Basic sprayer , without hose or gun Model 231–490 Complete sprayer with hose, “FLEX” gun, Reverse–A– Clean IV  Dripless  T ip Guard, and 517 size SwitchT ip ...

  • Hitachi EM 490 - page 2

      SAFETY W ARNINGS HIGH PRESSURE SPRA Y CAN CAUSE SERIOUS INJUR Y . FOR PROFESSIONAL USE ONL Y . OBSERVE ALL W ARNINGS. Read and understand all instruction manuals before operating the equipment. FLUID INJECTION HAZARD General Safety This equipment generates very high fluid pressure. Spray from the gun, leaks or ruptured com ...

  • Hitachi EM 490 - page 3

      MOVING P ARTS HAZARD Moving parts can pinch or amputate your fingers or other body parts. KEEP CLEAR of moving parts when starting or operating the sprayer . Follow the Pressure Relief Procedure on page 2 before checking or servicing any part of the sprayer , to prevent it from starting accidentally . EQUIPMENT MISUSE HAZA ...

  • Hitachi EM 490 - page 4

      A VERTISSEMENT La pulvérisation à haute pression peut causer de blessures très graves. Réservé exclusivement à l’usage professionnel. Observer toutes les consignes de sécurité. Bien lire et bien comprendre tous les manuels d’instructions avant d’utiliser le matériel. RISQUES D’INJECTION Consignes général ...

  • Hitachi EM 490 - page 5

      RISQUES EN CAS DE MAUV AISE UTILISA TION DU MA TERIAL Consignes générales de sécurité toute utilisation anormale de l’appareil du pulvérisation ou des accessoires comme, par exemple, la mise sous une pression excessive, les modifications de pièces, l’utilisation de produits chimiques et de matières incompatibles ...

  • Hitachi EM 490 - page 6

      ADVERTENCIA EL ROCIADO A AL T A PRESION PUEDE CAUSAR GRA VES LESIONES. SOLO P ARA USO PROFESIONAL. RESPECTE LOS A VISOS DE ADVERTENCIA. Lea y entienda todo el manual de instrucciones antes de manejar el equipo. PELIGRO DE INYECCION DE FLUIDO Seguridad general Este equipo general un fluido a una presión muy alta. El rociad ...

  • Hitachi EM 490 - page 7

      PELIGRO POR MAL USO DEL EQUIPO Seguridad general Cualquier mal uso del equipo pulverizador o los accesorios, tal como sobre presurización, modificación de piezas, uso de mate - riales y productos químicos incompatibles, o utilización de pie - zas dañadas o desgastadas, puede hacen que se rompan y causen la inyección ...

  • Hitachi EM 490 - page 8

      SETUP W ARNING If you are supplying your own hoses and spray gun, be sure the hoses are electrically conductive, that the gun has a tip guard, and that each part is rated for at least 2750 psi (190 bar) Maximum Working Pressure . This is to reduce the risk of serious bodily injury caused by static sparking, fluid injection ...

  • Hitachi EM 490 - page 9

      SETUP P ACKING NUT/WETCUP Keep filled with TSL Fig 1 FIL TER DO NOT INST ALL A SHUT OFF DEVICE HERE 50 ft. (15.2 m) MAIN FLUID HOSE ON/OFF SWITCH PRESSURE CONTROL KNOB 3 ft (0.9 m) HOSE RAC IV DripLess TIP GUARD and SwitchT ip OPERA TION W ARNING Pressure Relief Procedure To reduce the risk of serious bodily injury , inclu ...

  • Hitachi EM 490 - page 10

      OPERA TION Fig 2 ON/OFF SWITCH PRESSURE CONTROL KNOB RAC IV DripLess TIP GUARD and SwitchTip TURN CCW T O LOWER PRESURE PRESSURE DRAIN V AL VE 1. Prime the sprayer with paint. a. Close the pressure drain valve. b. Don’t install the spray tip yet! c. Put the suction tube into the paint container . d. T urn the pressure ...

  • Hitachi EM 490 - page 11

      OPERA TION 4. Cleaning a Clogged Tip W ARNING To reduce the risk of serious bodily injury from injec - tion, use extreme caution when cleaning or chang - ing spray tips. If the spray tip clogs while spraying, engage the gun safety latch immediately , then fol- low the procedure in Steps 4a to 4e, below . NEVER wipe of f ...

  • Hitachi EM 490 - page 12

      FLUSHING GUIDELINES NOTE: The Pressure Relief Procedure W arning is on page 14. When T o Flush CAUTION NEVER leave water in the sprayer if there is the slightest change it could freeze. Flush out the water with mineral spirits. If water freezes in the pressure control tube, it prevents the sprayer from being started, an ...

  • Hitachi EM 490 - page 13

      APPLICA TION METHODS Always hold the gun perpendicular to the work surface and at an even12 to 14 in. (300–356 mm) from the surface you are spraying. See Fig 9. Begin moving the gun in a horizontal direction at a steady rate. Start the spray stroke of f the target surface and pull the trigger as the gun is moving. The ...

  • Hitachi EM 490 - page 14

      TROUBLESHOOTING GUIDE W ARNING Pressure Relief Procedure To reduce the risk of serious bodily injury , including fluid injection, splashing in the eyes or on the skin, or injury from moving parts, always follow this procedure when you shut of f the sprayer , when checking, adjusting or cleaning the system, and when chan ...

  • Hitachi EM 490 - page 15

      PROBLEM CAUSE SOLUTION Paint leaks into wet–cup Throat packings are worn or damaged Replace the packings. See page 16. Excessive surging from spray gun Spray tip or fluid filter is plugged Disassemble and clean. Spray tip too big or worn Change the spray tip. Paint too viscous Thin the paint. W rong type hose Use mini ...

  • Hitachi EM 490 - page 16

      Fig 12 222 *206 *204 *207 215 52 33 34 58 223 A 36 55 10 TORQUE TO 70 ft–lb (95 N.m) 11 2 TORQUE T O 80 ft–lb (107 N.m) 54 38 Reinstalling the Pump. See Fig 12. 1. Rotate the crankshaft (A) so the connecting rod (54) is in its lowest position. (Rotate the fan blades at the rear of the motor with a screwdriver .) The ...

  • Hitachi EM 490 - page 17

      DISPLACEMENT PUMP Reassembly Procedure 1. Stack the backup washer (219*), U–cup seal (205*) lips down , and female gland (220*), alternate the polyethylene and leather v–packings (217*, 218*) lips up, and stack the male gland (213*) one at a time onto the piston valve (224). See Fig 15. 2. T ighten the packing retai ...

  • Hitachi EM 490 - page 18

      REPLACING THE CONNECTING ROD and BEARING W ARNING To reduce the risk of serious bodily injury , including fluid injection or splashing in the eyes or on the skin, or injury from moving parts, always follow the Pres- sure Relief Procedure W arning on page 14 be- fore checking, adjusting, cleaning or shutting of f the spr ...

  • Hitachi EM 490 - page 19

      REPLACING THE DRIVE ASSEMBL Y W ARNING To reduce the risk of serious bodily injury , including fluid injection or splashing in the eyes or on the skin, or injury from moving parts, always follow the Pres- sure Relief Procedure W arning on page 14 be- fore checking, adjusting, cleaning or shutting of f the sprayer . Unpl ...

  • Hitachi EM 490 - page 20

      REPLACING THE ELECTRIC MOT OR & CAP ACITOR W ARNING To reduce the risk of serious bodily injury , including fluid injection or splashing in the eyes or on the skin, or injury from moving parts, always follow the Pres- sure Relief Procedure W arning on page 14 be- fore checking, adjusting, cleaning or shutting of f t ...

  • Hitachi EM 490 - page 21

      REPLACING THE PRESSURE CONTROL & CIRCUIT BOARD W ARNING To reduce the risk of serious bodily injury , including fluid injection or splashing in the eyes or on the skin, or injury from moving parts, always follow the Pres- sure Relief Procedure W arning on page 14 be- fore checking, adjusting, cleaning or shutting of ...

  • Hitachi EM 490 - page 22

      PRESSURE CONTROL ADJUSTMENT USE EXTREME CAUTION WHEN PERFORMING THIS ADJUSTMENT PROCEDURE to reduce the risk of a fluid injection injury or other serious bodily injury , which can result from component rupture, electric shock, fire, explosion or moving parts. This procedure sets the sprayer to 2750 psi (190 bar) MAXIMUM ...

  • Hitachi EM 490 - page 23

      PRESSURE CONTROL ADJUSTMENT Fig 22 ON/OFF SWITCH A B D TIGHTEN C 4. Open the needle valve slightly . T urn the pressure con - trol knob (A) to the minimum setting. 5. Plug in the sprayer and turn the switch ON. Increase the pressure setting just enough to start the sprayer . Prime the hose, being sure to eliminate all a ...

  • Hitachi EM 490 - page 24

      P ARTS DRA WING – PRESSURE CONTROL Ref 25 Part No. 215–860 Ref No. 50 Pressure Control Assembly Includes replaceable items 301 to 316, as listed below NOTE: Numbers with “Ref” preceeding them correspond with the parts lists on pages 24 and 26. Ref 23 Ref 130 315 316 Ref 1 303 Ref 23f 306 305 Ref 23c 301 Ref 23a ...

  • Hitachi EM 490 - page 25

      DISPLACEMENT PUMP P ARTS DRA WING and LIST REF NO. P ART NO. DESCRIPTION QTY 201 180–656 PLUG 1 203 105–444* BALL, sst; 0.3125” dia. 1 204 105–445* BALL, sst; 0.5” dia. 1 205 105–522* SEAL, u–cup, polyurethane 1 206 176–761* GASKET , brass 1 207 176–759* PIN, ball stop 1 208 176–749* V–P ACKING, le ...

  • Hitachi EM 490 - page 26

      P ARTS LIST – SPRA YER WITH UPRIGHT CART Model 231–002, Series C, Basic Sprayer Includes items 1 to 135 as listed below REF NO. P ART NO. DESCRIPTION QTY REF NO. P ART NO. DESCRIPTION QTY 1 065–099 CONDUIT , electrical 4 in. 3 100–188 NUT , hex, 5/16–18 7 4 100–214 LOCKW ASHER, spring, 3/8” 9 7 101–344 C ...

  • Hitachi EM 490 - page 27

      P ARTS DRA WING – SPRA YER WITH UPRIGHT CART 120 4 23d* 55 55e 55f 55c 55b 11 3 19 35 20 18 53 54 3 129a 52 10 11 2 58 38 29 14 34 33 34 33 36 55d 55a 23 23e 129 37 27 25 40 Ref 312 313 302 84 Ref 52 47 122 123 11 9 46 95 99 97 132 7 Ref 40 50 SEE DET AIL BELOW 4 Ref No. 23 Electric Motor Includes items 23a to 23g Ref ...

  • Hitachi EM 490 - page 28

      P ARTS LIST – SPRA YER WITH LOBOY CART Model 220–679, Series C, Basic Sprayer Includes items 1 to 135 as listed below REF NO. P ART NO. DESCRIPTION QTY REF NO. P ART NO. DESCRIPTION QTY 1 065–099 CONDUIT , electrical 4 in. 3 100–188 NUT , hex, 5/16–18 7 4 100–214 LOCKW ASHER, spring, 3/8” 9 7 100–057 CAP ...

  • Hitachi EM 490 - page 29

      P ARTS DRA WING – SPRA YER WITH LOBOY CART 33 11 6 11 7 29 126 11 5 55f 55e 37 27 23d 23 23e 7 1 129b 129 99 129a 132 Ref 40 124 11 7 38 58 33 36 34 35 19 20 18 53 54 55c 55b 3 4 3 52 10 11 2 14 55a 55d 127 50 25 40 Ref 312 313 302 84 Ref 52 47 122 123 120 11 9 46 95 50 Ref No. 50 Pressure Control See page 23 for part ...

  • Hitachi EM 490 - page 30

      ACCESSORIES Spanish 185–961 German 186–041 Greek 186–045 Korean 186–049 Apply other language here DANGER LABELS The English language DANGER label shown on page 1 and the same label in French is on your spray - er . If you have painters who do not read English or French, order one of the following labels to apply ...

  • Hitachi EM 490 - page 31

      TECHNICAL DA TA Maximum W orking Pressure 2750 psi (190 bar) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Motor 3/4 HP , AC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Requirements 120V AC, 60Hz, 15 amp or 4500 W att Generator . ...

  • Hitachi EM 490 - page 32

      THE GRACO W ARRANTY AND DISCLAIMERS W ARRANTY Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. As purchaser ’ s sole remedy for breach of this warranty , Gra ...

Fabricante Hitachi Categoría Paint Sprayer

Los documentos del dispositivo Hitachi EM 490 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Hitachi
- manuales de instrucciones EM 490
- hojas de producto Hitachi
- folletos informativos
- o etiquetas energéticas Hitachi EM 490
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Hitachi EM 490.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Hitachi EM 490, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Hitachi EM 490. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Hitachi EM 490.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Hitachi EM 490, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Hitachi EM 490. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Hitachi EM 490.

El manual de instrucciones completo de Hitachi debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Hitachi EM 490 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Hitachi EM 490, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Hitachi EM 490 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Hitachi EM 490 - que deben facilitarnos los primeros pasos durante el uso de Hitachi EM 490
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Hitachi EM 490
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Hitachi EM 490 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Hitachi EM 490?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Hitachi EM 490, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Hitachi EM 490 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)