-
TANDBERG MSE 8510 - page 1
Codian MCU MSE 8510 Getting started ...
-
TANDBERG MSE 8510 - page 2
Codian MCU MSE 8510 Getting started ...
-
TANDBERG MSE 8510 - page 3
Copy right © Codian 2008. All rights reser ved. This Getting Star ted Guide ma y not be copied, photocopied, translated, r eproduc ed, or con verted into any electronic or machine-readable form in whole or in par t without prior wr itten appro v al of Codian Limited. Codian Limited reser ves the r ight to revise this documenta tion and to make cha ...
-
TANDBERG MSE 8510 - page 4
T able of conten ts General inf ormation .......... .......... .......... ........... .......... .......... ............. .......... ........... .......... .. .... . 1 About the M SE 8510 Media 2 blade ........... ............ ............. .......... ............. ........... 1 Port and L ED location .............. ........... ............ ....... ...
-
TANDBERG MSE 8510 - page 5
General information 1 General informa tion About the MSE 8510 Media2 blade The MSE 8510 Media2 blade is a technologically adv anced media processor that fits into an MSE 8000 chassis. It can be used as a Multipoint Control Unit (MCU) combining continuous presence high defini tion video conferencing and the highest possible v oice quality . P ort an ...
-
TANDBERG MSE 8510 - page 6
2 LED behavior T able 1 descr ibes the behavior of the LEDs . T able 1: Media2 blade LED behavior LED Co lor Indicates USB P or t Activity Green Reser ved for futur e expansion Admin P or t Activity Green Reser ved for future expansion Status Green The Media2 blade is opera ting nor mall y Alar m Red The Media2 b lade is booting or has dev eloped a ...
-
TANDBERG MSE 8510 - page 7
Installing the Media2 blade 3 Installing the Media2 blade Step one: Install the Media2 blade into the MSE 8000 chassis 1 Remov e the blade or blanking blade from the slot into which you are going to install the Me dia2 blade: i Using a No .1 Phillips scre wdriver , loosen the scre ws in the retaining latches with an anti-cloc kwise quar ter tur n. ...
-
TANDBERG MSE 8510 - page 8
4 iii Slide out the blade or bl anking bl ade. 2 Open both retaining la tches on the front of the Media2 b lade. When open, a retaining latch is at a 90 ° angle perpendicular to the front of the blade . 3 Slide the Media2 blade into the b lade slot (as sho w n in Figure 2) un til it stops. 4 Simultaneousl y close both retaining latches on the blad ...
-
TANDBERG MSE 8510 - page 9
Installing the Media2 blade 5 Figur e 3: Closing the retaining latches on the front of a blade Step two: C onnec t to Ethernet Port A Connect an Ethernet cable from Ethernet P or t A to an Ether net switch (rather than a hub , to minimize interference from othe r devices on the netw ork). The Ether net por t is a 10/100/1000 Mbps auto-sensing conne ...
-
TANDBERG MSE 8510 - page 10
6 Initial configur ation Step one: Configur e Ethernet Port A settings The default setting for the Media2 blade Ether net por ts is auto-sensing mode . If the switch por ts to which you con nect the Media2 blade ar e not also set to auto-sensing mode, then y ou need to configure the Medi a2 blade Ethernet por ts to use the same speed and duplex mod ...
-
TANDBERG MSE 8510 - page 11
Configuring the Media2 blade 7 Co nfiguring the Media2 blade Step one: Log in to the Media2 blade All administration of the Medi a2 blad e is perfor med via the w eb interface. T o log in to the w eb interface of the Media2 b lade: 1 Log in to the Super visor’ s web interface . 2G o t o Hardware > Blades and clic k the IP address of the Media2 ...
-
TANDBERG MSE 8510 - page 12
8 T o configure the Media2 b lade to use a SIP registrar: 1 In the w eb interface , go to Settings > SIP . 2 Configure the settings y ou requir e , usin g the online help for fur ther assistance. 3C l i c k App ly c han ges . Step four: Add endpoints (optional) One wa y to add par t icipants to a confer ence that you cr eate is to hav e the Medi ...
-
TANDBERG MSE 8510 - page 13
Using the Media2 blade 9 Using the Media2 blade Creating conferences T o crea te a conference: 1 In the w eb interface of the Media2 b lade, go to Conf er en ce s and click Ad d n ew confer ence . 2T y p e a Name for the conference, for example SalesMeeting . 3 T ype an optional numeric identifier , for example 123 . This will be the telephone numb ...
-
TANDBERG MSE 8510 - page 14
10 Calling partic ipants in to a conferenc e T o call par ticipants in to a conference: 1 In the w eb interface of the Media2 blade, go to Con fe re nc es and click on the name of an activ e conference . 2O n t h e Pa r ti c ip an ts tab , click Add par ticipant to call out to an H.323 or SIP endpoint. 3I n t h e Address field: where there is no H. ...
-
TANDBERG MSE 8510 - page 15
Using the Media2 blade 11 Streaming conferences Streaming is a wa y of viewing a conference in a standard w eb bro wser . The Media2 blade allo ws streaming of video and, if enabled for a confer ence , the streaming of data. Y ou can also conduct a text ‘chat’ and add notes and dra wings to the data stream. Y ou can configure tw o streaming opt ...
-
TANDBERG MSE 8510 - page 16
12 Instruc ting confer ence par ticipants Y ou need to tell conference par ticipants ho w to join conferences . Y ou can also tell them ho w to use the Far-End Camera Contr o ls (FECC) to na vigate menus in the auto attendant and choose conference la youts. Ther e is a document: Getting Started: Accessing Conferences a vailable in the documenta tio ...
-
TANDBERG MSE 8510 - page 17
Troubleshooting and tec hnical support information 13 T r oubleshooting and technical suppor t information Using the ev ent log to help solve a problem Unless you are ex periencing a prob lem, all e v ent logging sources should be set to the default, which is Errors, warnings and information . F or more infor mation about configur ing the ev ent lo ...
-
TANDBERG MSE 8510 - page 18
61-0021-01 ...
¿Tienes una pregunta acerca de TANDBERG MSE 8510?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con TANDBERG MSE 8510, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con TANDBERG MSE 8510 probablemente compartirá una forma de solucionarlo.