-
Audiovox AMP-595C - page 1
Owner's Owner's Owner's Owner's Owner's Manual Manual Manual Manual Manual Model AMP-595 300 W att Stereo Amplifier ...
-
Audiovox AMP-595C - page 2
INDEX Specifications ................................................................................1 Precautions ...................................................................................2 Installation Instructions .................................................................3 Wiring Instructions ..................................... ...
-
Audiovox AMP-595C - page 3
HIGH PERFORMANCE STEREO AMPLIFIER This power amplifier has been designed to provide high quality performance with a minimum of maintenance. However, it's performance will only be as good as the care and quality of components with which it is installed. We therefore advise that you read these instructions very carefully to familiarize yourself ...
-
Audiovox AMP-595C - page 4
PRECAUTIONS 1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired correctly. Please follow the wiring instructions carefully for the type of system being used. 2. The last lead to be connected is the wire to the positive ( + ) terminal of the battery. Connect this wire only ...
-
Audiovox AMP-595C - page 5
INSTALLATION INSTRUCTIONS INSTALLATION DIAGRAM 1. Select a mounting area where the amplifier will have sufficient air circulation for proper cooling. Inadequate air circulation will cause the temperature of the amplifier to rise and will trigger the thermal protection mode. 2. Place the amplifier on the mounting surface and mark the locations of th ...
-
Audiovox AMP-595C - page 6
WIRING INSTRUCTIONS The wiring of your amplifier will depend on the system and speakers you are using but will either be a stereo, mono, or mixed-mono application. The following pages illustrate the input and output wiring for both types. Please refer to the appropriate diagrams for the system configuration you are using. The power and speaker wire ...
-
Audiovox AMP-595C - page 7
4. Speaker Connections Depending on the type and number of speakers used with the amplifier, wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #18 gauge wire should be used for the speaker leads but in no case thinner than #20 gauge. For leads in excess of 10 feet, #16 gauge is recommended. When wiring ...
-
Audiovox AMP-595C - page 8
STEREO AND MIXED-MONO INPUT WIRING DIAGRAM -6- 5-PIN CONNECTOR IMPORTANT USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUTS, NOT BOTH. HIGH-LEVEL (SPEAKER) OUTPUTS CAR STEREO USE THIS INPUT WIRING WITH OUTPUT WIRING ON PAGE 7 RCA TYPE SHIELDED CABLE (NOT INCLUDED) RIGHT + RIGHT - LEFT - LEFT + LOW-LEVEL RCA OUTPUTS GREEN WHITE GRAY BROWN LEFT RIGHT BLACK CH ...
-
Audiovox AMP-595C - page 9
STEREO AND MIXED-MONO OUTPUT WIRING DIAGRAM -7- AUTO-ANTENNA LEAD LEFT SPEAKER - USE #14 GAUGE WIRE (SEE TEXT) + CAR STEREO RIGHT SPEAKER CONNECT THIS WIRE LAST - + USE THIS OUTPUT WIRING WITH INPUT WIRING ON PAGE 6 EXISTING SCREW OR BOLT CLEAN PAINT, RUST, DIRT OR GREASE FROM AREA FOR GOOD CONNECTION GROUNDED METAL SECTION OF VEHIC ...
-
Audiovox AMP-595C - page 10
-8- MONO (BRIDGED) INPUT WIRING DIAGRAM CAR STEREO LOW-LEVEL RCA OUTPUTS "Y" RCA TYPE SHIELDED CABLE (NOT SUPPLIED) TO 2nd AMPLIFIER IMPORTANT USE EITHER HIGH OR LOW-LEVEL INPUTS, NOT BOTH. HIGH-LEVEL (SPEAKER) OUTPUTS + - + - TO 2nd AMPLIFIER 5-PIN CONNECTOR USE THIS INPUT WIRING WITH OUTPUT WIRING ON PAGE 9 GREEN WHITE GRAY BROWN NOTE: ...
-
Audiovox AMP-595C - page 11
-9- CAR STEREO MONO (BRIDGED) OUTPUT WIRING DIAGRAM - + MONO SPEAKER OR SUB-WOOFER 4 - 8 OHMS AUTO-ANTENNA LEAD USE THIS OUTPUT WIRING WITH INPUT WIRING ON PAGE 8 NOTE: MODE SWITCH ON AMPLIFIER IN MONO (MO) SETTING FOR THIS WIRING. USE #14 GAUGE WIRE (SEE TEXT) CONNECT THIS WIRE LAST EXISTING SCREW OR BOLT CLEAN PAINT, RUST, DIRT OR GREASE ...
-
Audiovox AMP-595C - page 12
-10- OPERATION After initial set-up, the amplifier should not require any further adjustment unless there is a change in the car stereo or speaker system with which it is used. 1 Power Indicator Lamps The Power Indicator Lamps will light to indicate that the unit is connected to the battery and that the Remote Turn-On terminal is receiving +12 volt ...
-
Audiovox AMP-595C - page 13
-11- by the temperature of the unit rising above a safe level or by an overload condition. If activated by a rise in temperature, the unit will resume operation after cooling off to a normal operating range. If activated by an overload condition, the source of the overload must be found an d corrected to resume operation of the amplifier. Most over ...
-
Audiovox AMP-595C - page 14
8 Cooling Fan This unit incorporates a fan to provide continuous air flow through the unit to keep the heat-sink and components safely within their operating temperature range. The fan is automatically activated whenever +12 volts is supplied to the Remote Turn-On terminal. -12- 9 Fuse The circuitry of the amplifier is protected from damage by an a ...
-
Audiovox AMP-595C - page 15
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (a ...
-
Audiovox AMP-595C - page 16
© 1998 Audiovox Corporation, Hauppauge, N.Y. Printed in Korea 128-5306 ...
¿Tienes una pregunta acerca de Audiovox AMP-595C?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Audiovox AMP-595C, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Audiovox AMP-595C probablemente compartirá una forma de solucionarlo.