-
Bosch Appliances SHU53 - page 1
...
-
Bosch Appliances SHU53 - page 2
ENGLISH - 1 ENGLISH www.boschappliances.com INTRODUCTION .................................................. . 2 T OOLS AND MA TERIALS NEEDED ......................... . 3 MA TERIALS SUPPLIED .......................................... . 4 CHOOSING LOCA TION ......................................... . 5 PLUMBING PREPARA TION ......................... ...
-
Bosch Appliances SHU53 - page 3
2 - ENGLISH www.boschappliances.com INTRODUCTION In addition to these instructions the dishwasher shall be installed: • In the United States, in accordance with the National Electric Code/State and Municipal codes and/or local codes. • In Canada, in accordance with the Canadian Electric Code C22.1 -latest edition/Provincial and Municipal codes ...
-
Bosch Appliances SHU53 - page 4
ENGLISH - 3 ENGLISH www.boschappliances.com TOOLS & MATERIALS NEEDED Tools Needed for Installation Additional materials may be required to comply with local codes. Figure 2 Materials Needed Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line. Shut-off valve and fittings for hot water supply line. 90 ...
-
Bosch Appliances SHU53 - page 5
4 - ENGLISH www.boschappliances.com MATERIALS SUPPLIED DISHWASHER INSTALLATION KIT (Clear Bag) D. T oe Panel Screws (8mm) (2) E. Mounting Brackets (1L & 1R) F. Mounting Bracket Screws (2) G. Rubber Connection Hose (1) and Drain Hose Clamps (2) SHY66 & SHX56 Models • Dishwasher Installation Kit (1) and • ( Green Bag ) w/ the following: L ...
-
Bosch Appliances SHU53 - page 6
ENGLISH - 5 ENGLISH www.boschappliances.com Select a location as close to the sink as possible for ready access to water and drain lines. Most of the installation work is done before the dishwasher is moved into place. Any built-in dishwasher must be fully enclosed on the top, both sides and back. Therefore the cabinet space below your counter is p ...
-
Bosch Appliances SHU53 - page 7
6 - ENGLISH www.boschappliances.com PLUMBING PREPARATION 1 . In order to reduce running time, Bosch recommends 140° F water inlet temperature. Your dishwasher will perform equally as well at 120° F water temperature, but the run time will be extended. Hot Water Supply • The hot water line to the dishwasher must provide between 5 - 120 psi (0.3- ...
-
Bosch Appliances SHU53 - page 8
ENGLISH - 7 ENGLISH www.boschappliances.com ELECTRICAL PREPARATION • Cut a 1” (25.4mm) diameter hole in the cabinet (in area of Figure 9 B). For wood cabinets, sand the hole until smooth. For metal cabinets, cover the edge with a grommet. • Run flexible cable (as codes permit) from junction through hole in cabinet. Cable should extend 30” ( ...
-
Bosch Appliances SHU53 - page 9
8 - ENGLISH www.boschappliances.com PLACING THE DISHWASHER Placing the Dishwasher The profile strips on the sides of the dishwasher allow the dishwasher to fit into a cabinet opening with a width of 23-5/8” (600 mm) to 24-1/8” (613 mm). Before sliding the dishwasher into the cabinet opening: • Straighten the hot water supply line and the elec ...
-
Bosch Appliances SHU53 - page 10
ENGLISH - 9 ENGLISH www.boschappliances.com DRAIN HOSE CONNECTION Drain Hose • Before beginning, turn off the water supply! • The access hole for the drain hose should be 1.25” (32 mm) diameter . • Use the hose clamps and rubber connection hose (Figure 3) to connect the drain hose to the sink, disposer or air gap (Figure 14). Figure 14 G, F ...
-
Bosch Appliances SHU53 - page 11
10 - ENGLISH www.boschappliances.com HOT WATER CONNECTION Openings for water lines must be installed in the marked areas as shown in Figures 8 and 9 to avoid interference with the dishwasher frame or other components. • If using a solder joint instead of a com- pression fitting, be sure to make all solder connections before connecting the water l ...
-
Bosch Appliances SHU53 - page 12
ENGLISH - 11 ENGLISH www.boschappliances.com ELECTRICAL SUPPLY CONNECTION • Install strain relief or conduit connector into opening on power supply box. • Strip the insulated wires, being extremely careful not to strip too much insulation. • Insert and securely fasten into strain re- lief , two-conductor supply cable with ground. • T wist w ...
-
Bosch Appliances SHU53 - page 13
12 - ENGLISH www.boschappliances.com If you have an SHI model, an integrated model, you will have additional mounting hardware and a folded template sheet with installation instructions comprised of pictograms. In North America the stainless steel models of the integrated series (SHI series), have a control panel that is 5-5/16” (135 mm) tall. Th ...
-
Bosch Appliances SHU53 - page 14
ENGLISH - 13 ENGLISH www.boschappliances.com Figure 19 DOOR PANEL INSTALLATION *Note: Do not exceed 30 5/16” (770mm) for the overall front panel length. SEE FOLDED PANEL INSTALLATION TEMPLATE SHEET FOR STEP BY STEP INSTRUCTIONS ON HOW TO INSTALL YOUR DISHWASHER PANEL(S). 1/4” max. (6 mm) 25” (636 mm) IMPORTANT Do NOT Drill Completely through ...
-
Bosch Appliances SHU53 - page 15
14 - ENGLISH www.boschappliances.com Figure 22 After installation of the dishwasher , open and close the door several times to make sure that it does so with ease. If the door closes too quickly or if the door falls open, the spring tension needs to be adjusted. To Adjust the Spring Tension • Obtain Spring T ension Screws (2) out of the SHI/SHV p ...
-
Bosch Appliances SHU53 - page 16
ENGLISH - 15 ENGLISH www.boschappliances.com SHY66 & SHX56 Series Base and Toe Panel Installation Steps BASE AND TOE PANEL Assembly Steps • Place J-Box Cover on J-Box, insert and tighten screw (Figure 26). • Drop screws inside holes in base part. • Slip Base Part under and up front bottom panel of dishwasher . Tighten Base Part Screws - L ...
-
Bosch Appliances SHU53 - page 17
16 - ENGLISH www.boschappliances.com TOE PANEL AND HANDLE • Obtain T oe Panel Screws from the Dishwasher Installation Kit bag (see Figure 3). • Insert screws through the T oe Panel. • With a T orx screwdriver , fasten screws and toe panel into dishwasher base. Regular Toe Panel Installation (for models other than SHY66 & SHX56) Figure 28 ...
-
Bosch Appliances SHU53 - page 18
ENGLISH - 17 ENGLISH www.boschappliances.com LEAVE INSTALLATION INSTRUCTIONS AND USE & CARE MANUAL WITH OWNER. Final Checklist Check Electrical Requirements. Be sure you have correct electrical supply and recommended grounding method. T urn on the hot water shut-off valve and electrical supply . Incoming water temperature should be 120°F-140° ...
-
Bosch Appliances SHU53 - page 19
18 - ENGLISH www.boschappliances.com ...
¿Tienes una pregunta acerca de Bosch Appliances SHU53?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Bosch Appliances SHU53, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Bosch Appliances SHU53 probablemente compartirá una forma de solucionarlo.