-
Intel SIM4-02 - page 1
© Intel Corporation 1972 ® INTEL CORP. 3065 Bowers Avenue, Santa Clara, California 95051 • (408) 246-7501 MICRO COMPUTER SYSTEMS SIM4-02 Hardware Simulator Nine PROMs (A0750 to A0758) plug into the SIM4-02 prototyping board, enabling your micro computer prototype to simulate and debug its own program. The Simulator when used in conjunction with ...
-
Intel SIM4-02 - page 2
CONTENTS Page 1.0 Introduction ............................................ . 2.0 Number Systems .......................................... . 3.0 Description 4.0 Directives ............................................... 2 5.0 Error Messages 4 6.0 Operating Instructions ...... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 6.1 ...
-
Intel SIM4-02 - page 3
SIM4-02 HARDWARE SIMULATOR 1.0 INTRODUCTION The SIM4-02 Hardware Simulator is a program written for the MCS-4 ™ series Micro Computer System. This program will provide interactive control over the debugging of other MCSA ™ programs. The minimum configuration requited is a SI M4-02 prototype card with three 4002 RAMs and a Teletype. When fully s ...
-
Intel SIM4-02 - page 4
A breakpoint register is associated with the simulated execution mode of operation, allowing the user to pre-set a location which will cause an interrupt before execution. The BREAK key on the teletype may also be used to interrupt execution and some other types of output. During'simulated execution, a count is kept of the number of simulated ...
-
Intel SIM4-02 - page 5
A Accumulator This directive may be used to display and/or alter the contents of the simulated accumulator. A space or comma follow- ing the A will display in binary, the contents of the simulated accumulator. This or the A may be followed either by a new value to be entered, or by a carriage return to end the directive. C Carry/Link This directive ...
-
Intel SIM4-02 - page 6
5.0 ERROR MESSAGES Most of the errors which can be detected by the simulation program are identified by a single character typeout, followed by ringing the bell once. Six different types of errors are identified this way: CODE SIGNIFICANCE ? This is not a valid directive. Any printed graphic normally generated by the ASR33, which is not a valid dir ...
-
Intel SIM4-02 - page 7
return address using the L directive. That may then be pushed down with the S directive, so that the starting address may be loaded into the first subroutine level, or the process may be repeated up to three times. If it is desired to force an inter~ rupt at the first occurrence of a JMS instruction, the stack pointer may be set to 3 initially, so ...
-
Intel SIM4-02 - page 8
the typing of some specializ~d sequences of characters, partial decimal to binary conversion on input, and 6-bit teletype char- acter input with control character checking. A test program may use these subroutines to facilitate checkout of complex programs, or the ROM may be included in the final program if teletype interface and the same ancillary ...
-
Intel SIM4-02 - page 9
8.0 RAM USAGE The simulation program, to facilitate full usage of the RAM, has organized it into a nominal block of 64 registers, each containing 16 main memory locations and four status locations. Directives which reference RAM as such (i.e., 0, M, and 0), always address it by a register number, and sometimes by a character position within the reg ...
-
Intel SIM4-02 - page 10
The bank number in the chart above is the value of the accumulator during a DCl instruction, needed to address that bank of RAMs. The port number given corresponds to the number typed out during simulation of the WMP instruction. Register positions 16-19 (Le., the status locations) are normally addressed in the program by the RDO/WRO, RD 1 /WR 1, e ...
-
Intel SIM4-02 - page 11
ASTERISK IS SIMULATOR OUTPUT INITIALIZE ~ ~EADY INDICATION .L. MEMORY BLOCK *Q0 ., 12!j IS ASSIGNED /r .10 01 0:BPP~PNPPPF BPPPPPPPNF 2:BPP~P~PPNF 31BNNNPNPNPF INPUT COMMAND 4:8."POl~PPPPF 518P.'J:-JPNPPPF 618PPNPNPPNF 71BNNNPNPNPF SPECIF IES OR IGI N 1 ~::~~~~~~::~: 1 ~:::~:~:~::~ ::~~;~::;:. : ~::~:~~;~~~~ SIMULATOR ASSIGNS ADDRESS IN A ...
-
Intel SIM4-02 - page 12
FIRST LINE DUMP RAM COMMAND £ LOCATION 3 1110 1010 = RDR *Z *00 20 2 8 0 1 2 9 14 10 11 0 6 8 2 9 14 11 1 5 0 6 8 11 2 14 1 4 0 0 0 " 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 " 0 0 0 0 0 " 0 " " 0 " 0 0 0 0 11) 11) " 0 0 0 0 " " 0 " 0 0 0 " 0 0 " 0 0 " 11 '" " " " ...
-
Intel SIM4-02 - page 13
01BPPNPNPPPF 41BNPNNPPPPF 81BNPNNPPPPF 121BPPPPPPPPF 9 14 10 0 0 0 0 2 I BPPNPNPPNF 61 BPPNPNPPNF 10 I BPPPPPPPPF 141BPPPPPPPPF Figure 9.3 Miscellaneous Directives. 11 ...
-
Intel SIM4-02 - page 14
fiH/ 0:START. rIM 4P 0 2: SRC 4P 3: RDR 4ft: XCH 0 5% INC 8 6: SRC 4P 7: RDR 8: XCH I 9: JMS AND II: XCH 2 12: WMP 13: JUN START IS: NOP 16: =104ft 104:/ 104: AND. Cl.B 105: XCH 2 106: l.DM 4 107: XCH 0 108: RAR 109: XCH 0 110: JCN CZ ROTRI 112: XCH I 113: RAR 114: XCH I liS: ROTR2. XCH 2 116: RAR 117: XCH 2 118: DAC I 19: JCN AN Z AN D+ 3 121: B8L ...
¿Tienes una pregunta acerca de Intel SIM4-02?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Intel SIM4-02, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Intel SIM4-02 probablemente compartirá una forma de solucionarlo.