-
ATEN ACS-1602 - page 1
User Manual ACS-1602 Read this guide thoroughly and follow the installation and operation procedures carefully in order to prevent any damage to the unit and/or any devices that connect to it. This package contains: M 1 ACS-1602 ADC KVM Switch M 2 ADC Cables (1.8m) M 1 User Manual M 1 Quick Start Guide If anything is damaged or missing, contact you ...
-
ATEN ACS-1602 - page 2
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec tion against harmful interference in a residential installation. This equipment generat es, uses and can radiate radio frequency energy, and if not instal ...
-
ATEN ACS-1602 - page 3
Overview The Master View ACS-1602 ADC KVM Switch is a two port control unit that allows access to two ADC equipped Macintosh systems from a single ADC console (USB keyboard, USB mouse, and ADC display). DVI equipped PCs can also be accessed from the ADC console with the use of an ADC to DVI adapter. ADC (Apple Display Connector) is a digital interf ...
-
ATEN ACS-1602 - page 4
Features M Provides control of two ADC enabled computers from a single ADC console (ADC Display, USB keyboard, USB mouse). M Supports all 15,17, 22, and 23 inch Apple ® ADC Cinema & Studio Displays. M Supports 19 inch analog CRT ADC monitors. M Easy to install - no software required - simply connect the ADC cables. M Easy to operate - computer ...
-
ATEN ACS-1602 - page 5
Hardware Requirements Console M An ADC Cinema or Studio Display; or an analog ADC CRT monitor M A USB Keyboard M A USB Mouse Computer Either an ADC equipped Mac, or DVI equipped PC with an ADC to DVI adapter (see the Cables section, below). Cables Because the ACS-1602 supports both digital and analog signals, the integrated (digital and analog) Cus ...
-
ATEN ACS-1602 - page 6
Components Front View: 1. Port Selection Switch Press this switch to toggle the KVM focus between the two ports. 2. Port LEDs M The On Line LED lights ORANGE to indicate that the computer connected to its corresponding port is up and running. M The Selected LED lights GREEN to indicate that the computer connected to its corresponding port is the on ...
-
ATEN ACS-1602 - page 7
Rear View: 1. ADC Port 2 The cable that connects to the ADC port on the computer you are designating as Computer 2 plugs in here. 2. ADC Port 1 The cable that connects to the ADC port on the computer you are designating as Computer 1 plugs in here. - 5 - 1 2 2003-04-22 ...
-
ATEN ACS-1602 - page 8
Installation To set up your ACS-1602 installation, refer to the diagram below and the one on p. 8 as you do the following: 1. Plug your USB keyboard and USB mouse into the USB ports on the back of the ADC display. - 6 - 1. Before you begin, make sure that power to all the devices you will be connecting up have been turned off. You must unplug the p ...
-
ATEN ACS-1602 - page 9
2. Plug the cable from the ADC display into the Console port connector of the Master View ACS-1602. 3. Use the ADC cables provided with this package to connect the ACS-1602 ’ s ADC ports to the ADC ports of the computers you are installing. Note: If your computer uses a DVI type connector, you will have to use an ADC to DVI adapter (requires sepa ...
-
ATEN ACS-1602 - page 10
- 8 - ADC-to-DVI Adapter AC Powe r PC Mac DV I USB 2003-04-22 ...
-
ATEN ACS-1602 - page 11
Port Selection Simply press the Port Selection switch on the ACS-1602 ’ s top panel to toggle the KVM focus between the computers (ADC1, ADC2). The Selected LED on the top panel lights to indicate which port is active. Note: For the Mac, if any USB storage devices are attached to the ADC ’ s USB ports, the following warning message appears when ...
-
ATEN ACS-1602 - page 12
Powering Off To power off your ACS-1602 installation, do the following: 1. Turn Off the ADC display 2. Turn Off the power to the computers. Modifying the Installation If you should ever need to take down, or change components on your ACS-1602 installation, do the following: 1. Power Off the installation as described in steps 1 and 2, above. 2. Unpl ...
-
ATEN ACS-1602 - page 13
TroubleShooting Symptom Possible Cause Action Keyboard and/or Mouse Not Repsonding Loose Cables Check all cable connections to make sure they are completely seated in their sockets. Keyboard and/or Mouse needs to be reset Unplug the keyboard or mouse from the USB port on the ADC display ’ s rear panel, then plug it back in. Master View needs to b ...
-
ATEN ACS-1602 - page 14
Specifications Function Specification Computer Connections 2 Port Selection Push Button Switch LEDs Selected 2 Green Online 2 Orange Connectors Console 1 x ADC-35 female Computers 2 x ADC-35 female Resolution 1920 x 1200; DDC,DDC2,DDC2B Environment Operating Temperature: 0 ~ 50 o C Storage Temperature: -20 ~ 60 o C Humidity: 0 ~ 80% RH Noncondensin ...
-
ATEN ACS-1602 - page 15
Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR ’ S LIABI LI TY EXCEED THE PRICE PAID FOR THE PRODUCT FROM THE DIRECT, INDIRECT, SPECIAL, INCI DENT AL OR CONSEQUENTIAL DAMAGES RESULTING FRO M THE USE OF THE PRODUCT, DISK OR ITS DOCUMENTAT ION. The direct vendor makes no warranty or representation, expressed, implied, or statutory wit h respe ...
-
ATEN ACS-1602 - page 16
Notes - 14 - 2003-04-22 ...
¿Tienes una pregunta acerca de ATEN ACS-1602?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con ATEN ACS-1602, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con ATEN ACS-1602 probablemente compartirá una forma de solucionarlo.