-
Porter-Cable 2621 - page 1
Double Insulated Portable Electric Drills Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e refer ence. Model No. ______________________________________ T ype ___________________________________________ Serial No. ____________________________ ...
-
Porter-Cable 2621 - page 2
2 WARNING: SOME DUST CREA TED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer , birth defects or other repr oductive harm. Some examples of these chemicals are: · lead from lead-based paints, · crystalline silica from bricks and cement and other masonry pr oducts, and · ars ...
-
Porter-Cable 2621 - page 3
3 9. USE SAFETY GLASSES. W ear safety glasses or goggles while operating power tools. Also face or dust mask if operation creates dust. All persons in the area wher e power tools are being operated should also wear safety glasses and face or dust mask. 10. DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from r eceptacle. Keep ...
-
Porter-Cable 2621 - page 4
4 4. VERIFY the drill’ s rotation before starting the drill so it is corr ect for the operation being performed. 5. NEVER change direction or r otation of reversing model until motor has completely stopped. 6. NEVER hold work in your hand, lap, or against other parts of your body when drilling. 7. DO NOT use drill as a router or try to elongate o ...
-
Porter-Cable 2621 - page 5
FUNCTIONAL DESCRIPTION FOREWORD Porter -Cable drills are designed to drill holes of various sizes in wood and metal as indicated in the following chart: INST ALLING AND REMOVING DRILL BIT (Except Keyless Models 2621, 6615) 1. CAUTION: DISCONNECT TOOL FROM POWER SOURCE. 2. The three-jaw chuck is designed for self-centering of the drill bit. Open jaw ...
-
Porter-Cable 2621 - page 6
6 3. Clean and insert smooth end of bit as far as it will go into the chuck, then withdraw bit approximately 1 / 16 ", or up to the flutes for small bits. 4. While holding the bit with one hand, turn outer sleeve (A) Fig. 2, clockwise until the bit is gripped in the chuck. 5. Tighten chuck by holding chuck ring (B) Fig. 2, with one hand while ...
-
Porter-Cable 2621 - page 7
7 4. REVERSING SWITCH – The reversing switch is located as indicated in Fig. 3. These models will operate in either the forward dir ection (clockwise rotation) for drilling holes, or the r everse direction (counter clockwise rotation) for releasing jammed drill bits. For counter clockwise rotation, stop the motor by releasing the trigger switch a ...
-
Porter-Cable 2621 - page 8
8 HOW TO USE THE DRILL GENERAL DRILLING 1. Be sure drill bit is secur ely gripped in chuck. (See INST ALLING AND REMOVING DRILL BIT). 2. Set REVERSING SWITCH for clockwise rotation. 3. Make sure work is held secur ely in vise or clamped in place prior to starting drilling operation. CAUTION: Loose work may spin and cause bodily injury . 4. Locate e ...
-
Porter-Cable 2621 - page 9
9 DRILLING MET AL In addition to the instructions listed under GENERAL DRILLING, the following also apply: CAUTION: When drilling metal, jamming of bit is more likely than when drilling other materials. 1. Use only good quality sharp high speed steel twist bits when drilling metal. 2. Start drilling with slow speed and gradually increase speed as d ...
-
Porter-Cable 2621 - page 10
10 6. Remove allen wrench fr om chuck. 7. INST ALL CHUCK RET AINING SCREW: T urn screw counter clockwise with a “flat” screwdriver . Tighten securely . BRUSH INSPECTION AND LUBRICA TION For your continued safety and electrical protection, brush inspection and replacement on this tool should ONL Y be performed by an AUTHORIZED PORTER-CABLE SER V ...
-
Porter-Cable 2621 - page 11
11 ACCESSORIES A complete line of accessories is available from your Porter -Cable • Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Porter -Cable Authorized Service Stations. Please visit our W eb Site www .porter -cable.com for a catalog or for the name of your nearest supplier . WARNING: Since accessories other than those ...
-
Porter-Cable 2621 - page 12
12 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter -Cable warrants its Professional Power T ools for a period of one year from the date of original purchase. W e will repair or replace at our option, any part or parts of the pr oduct and accessories covered under this warranty which, after examination, proves to be defective in workmanship or materia ...
-
Porter-Cable 2621 - page 13
The following are trademarks of PORTER-CABLE • DEL T A (Las siguientes son marcas registradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): BAMMER ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORT A-BAND ® , PORT A-PLANE ® , PORTER-CABLE ® , QUICKSAND ® , SANDTR ...
¿Tienes una pregunta acerca de Porter-Cable 2621?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Porter-Cable 2621, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Porter-Cable 2621 probablemente compartirá una forma de solucionarlo.