-
Datalogic DS2100N - page 1
DS2100N QUICK REFERENCE GUIDE Figure A 1 2 3 4 10 9 8 6 Warning and Device Class La bels "POWER ON" LED Mounting Holes "READY" LED "TRIGGER" L ED "COM" LED "STATUS" LED Push Button 7 Laser Beam Output Window 5 "GOOD" LED A ccessory Mounting Holes 11 NOTE This manual illustrates a St and Al ...
-
Datalogic DS2100N - page 2
DS2100N QUICK GUIDE 2 UPDATES AND LANGUAGE AVAILABILITY UK/US The latest drivers and documentatio n updates for this product are availabl e on Internet. Log on to: www.automation.datalogic.com I Su Internet sono disponibili le versio ni aggiornate di driver e documentazione di q uesto prodotto. Questo manuale è disponibile anche nell a versione it ...
-
Datalogic DS2100N - page 3
DS2100N QUICK GUIDE 3 STEP 1 – CONNECT THE SYSTEM To connect the system in a Stand Alone c onfigur ation, you nee d the hardware indicate d in Figure 1. In this l ayout the data is transmitted to the Host on the main ser ial interface. In Loc al Echo communication mode, the RS232 auxiliary interfa ce can be used to tra nsmit data indepe ndently f ...
-
Datalogic DS2100N - page 4
DS2100N QUICK GUIDE 4 25-pin Connector Pinout for DS2100N The table below giv es the pinout of the 25 -pin male D-su b connector fo r connection to the power supp ly and input/output signals. Use this pinout when the DS2100N reader is connected by means of the 25-pin c onnector: 13 25 14 1 Figure 2 - 25-pin Male D-su b Connector 25-pin D-sub male c ...
-
Datalogic DS2100N - page 5
DS2100N QUICK GUIDE 5 STEP 2 – MOUNT AND POSITION THE SCANNER 1. To mount the DS2100N, use the mounting bracket to obtain the most suitab le position for the r eader as shown in the figures below. Figure 3 - Positioning w ith Mounting Bracket 2. When mounting the DS2100N take into consi deration these three ideal label position angles: , Skew 10? ...
-
Datalogic DS2100N - page 6
DS2100N QUICK GUIDE 6 STEP 3 – X-PRESS™ CONFIGURATION X-PRESS™ is the intuitive Human Machine I nterface des igned to impr ove ease of installation and main tenance. Status and diagnostic information ar e clearly presented b y means of the five colored LEDs, whereas the sin gle push button gives immediate access to the follo wing relevant fun ...
-
Datalogic DS2100N - page 7
DS2100N QUICK GUIDE 7 3. Exit the process by pressing the X-PRESS™ push button onc e. The scann er will re start at the end of the process, and then the detected barc odes are automatically configured in scanner memory. NOTE If the barcode cannot be read becaus e of low c ontrast or excessiv e ambient light, you can perform the AutoSetup function ...
-
Datalogic DS2100N - page 8
DS2100N QUICK GUIDE 8 STEP 4 – INSTALL GENIUS™ CONFIGURATION PROGRAM Genius ™ is a Datalogic scanner configuratio n t ool providing several import ant advantages: • Wizard approach for new users; • Multi-language version; • Defined configuration dire ctly stored in the reader; • Communication protocol in dependent from the physic al i ...
-
Datalogic DS2100N - page 9
DS2100N QUICK GUIDE 9 a. Barcode selection and d efinition b. Operating mod e selection and definition c. Digital Outputs conf iguration d. Hardware inter face selection e. Output data form at configurati on The On Line operating Mode requires the r eader to be con nec ted to an External T rigger/Presence Sens or using I1A and I1B inputs. The A uto ...
-
Datalogic DS2100N - page 10
DS2100N QUICK GUIDE 10 2. After defining the paramet er values the following window appears allo wing to complete the reader configuration as follows: • Saving the configuration to disk; • Switching to Advanced mode; • Sending the configuration to the scanner. 3. After sending the configur atio n to the scanner you have comple te d the config ...
-
Datalogic DS2100N - page 11
DS2100N QUICK GUIDE 11 STEP 5 – TEST MODE Use a code suitable to your application to test the system. Alternativel y, you can use the Datalo gic Test Chart (Interleaved 2/5 or Code 39). 1. Enter the Test mode function by holding the X-PRESS™ push bu tton pressed until t he TEST LED is on. 2. Release the button to enter the Test mode function. O ...
-
Datalogic DS2100N - page 12
DS2100N QUICK GUIDE 12 ADVANCED SCANNER CONFIGURATION For further details on advanced product conf iguration, refer to the complete Reference M anual on the installation CD-ROM or downloadable from the web site through this link: www.automation.datalogi c.com/ds2100n . The following are alternative or advanced scanner configurat ion methods: HOST M ...
-
Datalogic DS2100N - page 13
DS2100N QUICK GUIDE 13 APPENDIX READING DIAGRAMS DS2100N-1200 (Standard Resolution) CONDITIONS Optic Version = Linear Code = Interleaved 2/5 Code 39 PCS = 0.90 Pitch angle = 0° Skew angle = 15° Tilt angle = 0° *Reading Conditions = Standard *Scan Speed = 500 scans/sec * Parameter select able in Genius™ (0,0) corresponds to the scanner output w ...
-
Datalogic DS2100N - page 14
DS2100N QUICK GUIDE 14 DS2100N-1204 High Performance (Standard Resolution) CONDITIONS Optic Version = Linear Code = Interleaved 2/5 Code 39 PCS = 0.90 Pitch angle = 0° Skew angle = 15° Tilt angle = 0° *Code Resolution: High - for 0.30 mm (12 mils) codes and smaller Standard - for 0.50 mm (20 mils) codes and greater *Reading Conditions = Standard ...
-
Datalogic DS2100N - page 15
DS2100N QUICK GUIDE 15 READING PERFORMANCE Version Reading Dis tance Max Code Reso lution mm (mils) Speed scans/s 1XX0 40 mm (1.6 in) - 300 mm (11.8 in) on 0.50 mm ( 20 mils) codes 0.20 (8) 500 to 800 1XX4 50 mm (1.8 in) - 310 mm (11.8 in) on 0.50 mm ( 20 mils) codes 0.20 (8) 800 to 1000 2XX0 30 mm (1.2 in) - 90 mm (3.5 in) on 0.30 mm (1 2 mils) co ...
-
Datalogic DS2100N - page 16
DS2100N QUICK GUIDE 16 MECHANICAL DIMENSIONS 23.3* 0.92 14 0.55 84 3.31 4 0.16 10.3 0.41 40 1.57 0.41 10.3 40 1.57 14.7 0.58 M 4 n° 4 1.29 32.7 mm inch 68 2.68 46 1.81 SETUP LEARN TEST READY GOOD TRIGGER COM STATUS DS2100N X PRESS INTERFACE * The quote refers to the scan line Figure 10 – DS2100N Overall Dimensi ons 9 4.2 7.8 20° 2.5 73 42 R 4 0 ...
-
Datalogic DS2100N - page 17
DS2100N QUICK GUIDE 17 COMPLIANCE LASER SAFETY This product conf orms to the applicable requirements of IEC 60825-1 and comp lies with 21 CFR 1040.10 ex cept for deviations pursuan t to Laser Notice N° 5 0, date June 24 , 2007. The scanner is classified as a Class 2 laser prod uct according to IEC 60825-1 regulati ons. Disconnect the pow er supply ...
-
Datalogic DS2100N - page 18
DS2100N QUICK GUIDE 18 PATENTS This product is covered by one or more of the follo wing patents: U.S. patent: 5,992,740 European patent: 789,315 B1 ...
-
Datalogic DS2100N - page 19
DECLARATION OF CONFORMITY 08 Datalogic A utomation S.r.l. Via S. Vitalino 13 40012 - Lippo di Calderara Bologna - Italy dichiara che declares that the déclare que le bescheinigt, daß das Gerät declare que el DS2100N Laser Scanner; e tutti i suoi modelli and all its models et tous ses modèles und seine Modelle y todos sus modelos sono conformi a ...
¿Tienes una pregunta acerca de Datalogic DS2100N?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Datalogic DS2100N, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Datalogic DS2100N probablemente compartirá una forma de solucionarlo.