-
Palsonic 2418 - page 1
PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA:1300 657 888 24CM AC/DC REMOTE COLOUR TELEVISION MODEL: 2418 OWNER'S MANUAL ...
-
Palsonic 2418 - page 2
. This equipment has been designed and manufactured to meet the highest international standards, but, like any electrical apparatus which is operated at mains voltage, care must be taken if you are to obtain the best results and safety is to be assured. This is particularly important with audio and TV equipment. read this handbook carefully and kee ...
-
Palsonic 2418 - page 3
ANT . PLUG MUTE CHANNEL SELECTOR ( ) VOLUME CONTROL ( ) SLEEP PICTURE PICTURE/TIME ( ) TIMER TIME CALL PREVIOUS CHANNEL SELECTOR ST AND BY IR RECEIVER INDICA TOR CONTROL BOARD FUSE ANT IN VIDEO IN AUDIO IN AUDIO OUT DEGAUSSING SWITCH DC IN EARPHONE JACK CH CH VOL VOL SKIP AUTO PSET FT FT 2 ANTENNA ...
-
Palsonic 2418 - page 4
INSTALLING BATTERIES : * Take care not to drop, dampen, disas- 1. Remove the battery cover of Remote semble the Remote Control Unit. Control Unit. * Operatable remote control range is 2. Insert two "AAA" 1.5V batteries making limited as shown. sure the polarity (+ or -) of the batteries matches the polarity marks inside the unit. 3. Close ...
-
Palsonic 2418 - page 5
Use the CHANNEL SELECTOR button on the Remote Control Unit to select channel. DC POWER SUPPLY: Be sure the DC power supply is 12V- 14V, attach the plug of DC power cord to the DC socket on the back of the cabinet. The set will be in stand by mode, the power indicator is red. If this television is being used in a mobile installation, attach the smal ...
-
Palsonic 2418 - page 6
llllllllllllll 1. Press the PSET (PRESET ON/OFF) button on the front panel. The current band and channel position will be displayed on screen (in green). 2. Press AUTO (AUTO PRESET) button, the appliance will search the signal of TV station in the order of VHFL, VHFH and UHF, as shown in the following, and memorise them from channel number 1 positi ...
-
Palsonic 2418 - page 7
0 1 2 58 59 SKIP BUTTON: FUNCTION: When CHANNEL SELECTOR button is used to select channels, the channel will be skipped if they are set to "SKIP" mode. For example: Set 2~7 channels to "SKIP" mode, the procedure of channel position increasing or decreasing. (REMOTE) (THE APPLIANCE) OPERATION: 1. Press PSET (PRESET ON/OFF) button ...
-
Palsonic 2418 - page 8
Press stand by button( ) on the appliance or the Remote Control Unit, the power indicator is red, the appliance is set to stand by mode. Press stand by button ( ) again, the appliance is turned on and the indicator is green. 8 AM 6 : 00 Press the PICTURE CONTROL button on the Remote Control Unit. The FUNCTION to be adjusted is selected in sequence ...
-
Palsonic 2418 - page 9
SLEEP BUTTON (REMOTE CONTROL UNIT) Using SLEEP button allows you to have the appliance automatically turned off a predetermined time, and set the appliance to stand by mode. After the SLEEP function is set, the remaining time will be automatically displayed for 4 seconds every ten minutes. * If you press STAND BY button while the SLEEP function is ...
-
Palsonic 2418 - page 10
5. Press TIME button, the CLOCK indicator is green instead of red ON TIME function starts operating. Then press STAND BY button to set stand by mode. 6. The appliance will be turned on automatically when the clock reaches your setting time. * The ON TIME operation will be cancelled if you switch off the power before your setting time is up. * If th ...
-
Palsonic 2418 - page 11
the upper comer of the screen for 4 seconds. Press AV/TV button again to return TV mode, the original channel will be displayed in the upper right comer of the screen. Set to TV mode when receiving or recording TV program. AV CONNECTOR This TV set is equipped with AUDIO/VIDEO input jacks and AUDIO output jack for your desired equipment to be connec ...
-
Palsonic 2418 - page 12
. TROUBLE SHOOTING GUIDE Many apparent malfunctions may be caused by slight misadjustment of regular controls or some other equally similar simple causes. If any problem arises in the operation of your set, first check through this list of symptoms and correction. Should the problem be unsettled, unplug the set and contact your dealer. Symptoms Che ...
-
Palsonic 2418 - page 13
SPECIFICATIONS : AC power adapter Power input Power output Dimension (W x H x D) Weight Car Battery Cord Remote Control Unit Power Supply : PAL/BG : DC 12V : VHFL 2-4; VHFG 5-12; UHF 28-61 : S1-S2 : 25cm : 0.7W Max. : VHF/CATV/UHF 75 ohm : 265 x 235 x 305 (mm) : 4.8 kg : AC 240V, 50Hz : DC 12V/4A : 154 x 118 x 56 (mm) : 0.5 kg : DC 3V (2 x AAA) * D ...
-
Palsonic 2418 - page 14
PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 604-10203-01 ...
¿Tienes una pregunta acerca de Palsonic 2418?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Palsonic 2418, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Palsonic 2418 probablemente compartirá una forma de solucionarlo.