-
NETGEAR XCM8944F - page 1
Inst allation NE T GE AR Pr oSAFE M6100 Chassis Swit ch XCM 8944, XCM8948, X CM8944F , XCM8924X , XCM89P , XCM89UP ...
-
NETGEAR XCM8944F - page 2
2 Cont ents M6100 Series Fr ont Panels ...................................................................................... 3 Bef or e Installing the S witch Blade ........................................................................... 4 Install the Chas sis ..................................................................................... ...
-
NETGEAR XCM8944F - page 3
3 M6100 Series Fr ont P anels Console ports U SB p or t 1 0G S FP+ po r ts 1 0G R J - 45 por t s XC M 8 92 4X XC M8 94 4 1 G R J- 45 po r ts 1 0G S FP+ po r ts 1 0G R J -45 po r t s 1 G SFP p or t s 1 0G S FP+ po r ts 1 0G R J - 45 por t s 1 G R J- 45 po r ts XC M8 94 4 F XCM8948 Oo B po r t USB p or t Oo B po r t Console ports Console ports Consol ...
-
NETGEAR XCM8944F - page 4
4 Bef ore Inst alling the Swit ch Blade The M6100 series swit ch blades ar e designed to be inst alled in the XCM8903 r ack-mount swit ch chassis. NET GEAR rec ommends installing the X CM8903 r ack-mount chassis int o a rack bef ore installing any s witch blades. F or mor e inf ormation about how t o install the X CM8903 r ack-mount switch chas sis ...
-
NETGEAR XCM8944F - page 5
5 Install the Chassis Y ou can either br acke t-mount the chassis into a r ack or install the chassis using the included r ails. For mor e information about installing the chas sis using rails, see the X CM8903 Har dwar e Installation Guide . ¾ T o br acket-mount the chassis: 1. P ar tially scr ew two of the included scr ews int o the rack wher e ...
-
NETGEAR XCM8944F - page 6
6 3. Scr ew the res t of the brack et t o the r ack . Install the F an T r ay ¾ T o install the f an tray: 1. Car efully slide the fan tr ay all the way int o the f an tray bay at the r ear of the chassis. The f an tray is c onnected t o power when it has been insert ed comple tely int o the f an tr ay bay . ...
-
NETGEAR XCM8944F - page 7
7 2. Scr ew the fan tr ay t o the r ear of the chassis using the included scr ews. Install the S witch Blade ¾ T o install a swit ch blade in a M6100 series chassis swit ch: 1. Select a slot f or the switch blade. 2. R emove a blank fr ont panel from the chassis slo t , if necessary . Any unoccupied s witch blade slo t in the chassis must have a b ...
-
NETGEAR XCM8944F - page 8
8 6. Using bo th hands, push bo th handles tow ar d the cent er of the swit ch blade, as shown. 7. Use your fingers or a scr ewdriver to turn the fr ont panel screws on each injector-ejector handle clockwise and comple tely down. When the scr ew is fully tightened, the yellow band ar ound the captive scr ew is complet ely hidden. Console XCM8948 S ...
-
NETGEAR XCM8944F - page 9
9 C AUTION: Be car eful to avoid over t or quing and stripping the scr ew heads. Install the P ow er Supply ¾ T o install the pow er supply : 1. Car efully slide the power supply all the way int o the power supply bay until it clicks into plac e. C AUTION: Do not slam the pow er supply int o the sy st em backplane. Use the locking handle to secur ...
-
NETGEAR XCM8944F - page 10
10 AC pow er c or d to the A C input connector below e ach power supply . W ARNING: Be sur e that the sour ce outle t is pr operly gr ounded bef or e plugging the AC pow er c or d into the input connector . Install Optional P oE (XCM89P) or UP oE (XCM89UP) Boar d Y ou can inst all an optional P oE (XCM89P) or UP oE (X CM89UP) boar d into the X CM89 ...
-
NETGEAR XCM8944F - page 11
11 2. C onnect the optional board and secur e it with the attached scr ews as shown. Configur e the S witch Blade Y ou can manage your swit ch thr ough its web management int erfac e or by using the command-line int erfac e (CLI) thr ough a console port . This guide shows you how to c onfigur e your swit ch using the web management int erfac e. I ...
-
NETGEAR XCM8944F - page 12
12 When configuring your s witch, c onnect your switch t o one of the number ed ports on the switch ’ s front panel. Do no t connect to the Out-of-Band (OoB) port for initial s witch c onfigur ation. N ote : Use the OoB port to manage the swit ch only a er the switch has been configur ed for your netw ork . For mor e inf ormation about swit ...
-
NETGEAR XCM8944F - page 13
13 used by the comput er NIC port when in DHCP-client mode without a DHCP ser ver pr esent . Use this IP value to log in t o the swit ch. Comput er with a St atic IP Addr ess When the comput er is in this mode, the swit ch must also be assigned a st atic IP addr ess. T o assign a s tatic IP addr ess, c onnect a V T100/ ANSI terminal or a workst ati ...
-
NETGEAR XCM8944F - page 14
14 N ote : Y ou might need to inst all the USB serial port driver available on the CD included with the package bef or e you can use the mini USB port on the comput er to c onnect to the switch. 3. C onfigur e the TEP to use the f ollowing settings : • Baud r ate . 115200 bps • Data bits . 8 • P arity . None • St op bit . 1 • ...
-
NETGEAR XCM8944F - page 15
15 ...
-
NETGEAR XCM8944F - page 16
16 8. C onnect your computer t o one of the number ed ports on the swit ch ’ s fr ont panel. 9. Ent er the IP addr ess you configur ed in the addr ess field of a br owser . A login scr een displays. 10. Ent er admin f or the user name and leave the passw or d field blank . 11. Click the Login butt on. The system inf ormation scr een displays. ...
-
NETGEAR XCM8944F - page 17
17 2. S tart a t erminal emulation pr ogram (TEP). 3. C onnect your computer t o a mini USB or RJ-45 console port on the fr ont panel of the blade. 4. C onfigur e the TEP to use the f ollowing settings : • Baud r ate . 115200 bps • Data bits . 8 • P arity . None • St op bit . 1 • Flow contr ol . None 5. T ype the show netw ...
-
NETGEAR XCM8944F - page 18
18 A login scr een displays. 8. Ent er admin f or the user name and leave the passwor d field blank . 9. Click the L ogin button. The system inf ormation scr een displays. 10. Configur e the switch f or your netw ork . For mor e information about c onfigur ation settings and options, see the M6100 Sowar e Administration Guide . ...
-
NETGEAR XCM8944F - page 19
19 ...
-
NETGEAR XCM8944F - page 20
NE T G E AR, I nc . 350 Eas t Pl um eri a D rive San J os e, C A 95134, U SA August 2014 T echnical Support Thank you f or selecting NETGEAR pr oducts. Aer installing your devic e, locat e the serial number on the label of your pr oduct and use it to regis ter your pr oduct at https ://my .net gear .com . Y ou must regis ter your pr oduct befor ...
¿Tienes una pregunta acerca de NETGEAR XCM8944F?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con NETGEAR XCM8944F, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con NETGEAR XCM8944F probablemente compartirá una forma de solucionarlo.