Español dropdown-ico

Manual de instrucciones Snapper YZ16385BVE, YZ16385BVE

37 de páginas 1.45 mb
Descargar

Pasar a la página of 37

Summary
  • Snapper YZ16385BVE, YZ16385BVE - page 1

    Safety Instructions & Operator’s Manual for SCRAMBLER HYDRO DRIVE SERIES 5 MODELS YZ16335BVE YZ16385BVE MODEL NUMBER EXPLANATION Y Z 16 33 5 B V E MODEL DESIGNATION ENGINE OPTIONS DRIVE SYSTEM TYPE ENGINE TYPE ENGINE HORSE POWER SERIES DESIGNATION CUTTING WIDTH Y – SCRAMBLER Z – Zero Turning Radius 16 – 16.0 HP Engine 33 - 33” Cutting ...

  • Snapper YZ16385BVE, YZ16385BVE - page 2

    2 IMPORTANT SAFETY INSTRUCTIONS WARNING: This pow erful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply w ith the follow ing SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these in ...

  • Snapper YZ16385BVE, YZ16385BVE - page 3

    3 IMPORTANT SAFETY INSTRUCTIONS PREPARATION (Continued From Previous Page) 7. Keep people and pets out of mow ing area. Immediately STOP blades, STOP engine, and STOP machine if anyone enters the area. 8. Check shields, deflectors, sw itches, blade controls and other safety dev ices frequently for proper operation and location. 9. Make sure all saf ...

  • Snapper YZ16385BVE, YZ16385BVE - page 4

    4 IMPORTANT SAFETY INSTRUCTIONS MAINTENANCE 1. DO NOT store machine or fuel container inside w here fumes may reach an open flame, spark or pilot light such as in a w ater heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of the reach of children in a we ll v ...

  • Snapper YZ16385BVE, YZ16385BVE - page 5

    5 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIO NS ........................................................................ 2-4 TABLE OF CO NTENTS ...................................................................................................... 5 SECTION 1 - FAMI LIARIZATI ON..................................................................... ...

  • Snapper YZ16385BVE, YZ16385BVE - page 6

    6 Section 1 - FAMILIARIZATION FIGURE 1.1 1. 1 INTRODUCTION This manual has been prepared for the operator’s of the SNAPPER SCRAMBLER. Its purpose, aside from recommending standard operating procedures and routine service requirements, is to promote SAFETY through the use of accepted operating practices. Read, Understand and Follow the IMPORTANT S ...

  • Snapper YZ16385BVE, YZ16385BVE - page 7

    7 Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 2.1.1. Check tires and add or release air as needed to bring pressure to 12 P.S.I. in front and 12 P.S.I. in rear tires. 2.1.2. Check guards, deflectors and covers to make sure all are in place and securely ...

  • Snapper YZ16385BVE, YZ16385BVE - page 8

    8 Section 2 - OPERATING INSTRUCTIONS IMPORTANT: This SCRAMBLER is equipped w ith hydrostatic driv e. The forw ard, rearw ard and steering movement of the machine is controlled by a joystick lever. Joy stick operations should be performed only from the operator’s position in the seat. A small movement of the joy stick can cause the machine to move ...

  • Snapper YZ16385BVE, YZ16385BVE - page 9

    9 Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT operate blades in reverse. STOP BLADES. LOOK and SEE behind and down for children, pets and hazards before and w hile backing. 2.2.3. MOWER BLADE 1. With engine running, move engine speed control to the Rabbit or “fast” position. 2. Pull the blade switch out into the “ON” position to engag ...

  • Snapper YZ16385BVE, YZ16385BVE - page 10

    10 Section 2 - OPERATING INSTRUCTIONS 2.3.5. CUTTING HEIGHT ADJUSTMENT This machine has seven different cutting height positions. IMPORTANT: When positioning the cutting deck into a higher cutting position, pull up on the deck lift handle only, it is not necessary to pull up on the release lever at the same time. Use the release lever when moving d ...

  • Snapper YZ16385BVE, YZ16385BVE - page 11

    11 Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the SCRAMBLER, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention the model and serial number. 3.2 SERVICE - AFTER FIRST 5 HOURS WARNING DO NOT atte ...

  • Snapper YZ16385BVE, YZ16385BVE - page 12

    12 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before w orking on mach ...

  • Snapper YZ16385BVE, YZ16385BVE - page 13

    13 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before w orking on mach ...

  • Snapper YZ16385BVE, YZ16385BVE - page 14

    14 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before w orking on mach ...

  • Snapper YZ16385BVE, YZ16385BVE - page 15

    15 Section 3 - MAINTENANCE WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before w orking on mach ...

  • Snapper YZ16385BVE, YZ16385BVE - page 16

    16 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before w o ...

  • Snapper YZ16385BVE, YZ16385BVE - page 17

    17 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before w o ...

  • Snapper YZ16385BVE, YZ16385BVE - page 18

    18 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remov e spark plug w ire from spark plug and secure aw ay from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before w ...

  • Snapper YZ16385BVE, YZ16385BVE - page 19

    19 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before w o ...

  • Snapper YZ16385BVE, YZ16385BVE - page 20

    20 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before w o ...

  • Snapper YZ16385BVE, YZ16385BVE - page 21

    21 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remov e spark plug w ire from spark plug and secure aw ay from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before w ...

  • Snapper YZ16385BVE, YZ16385BVE - page 22

    22 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remove spark plug wire from spark plug and secure aw ay from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before w o ...

  • Snapper YZ16385BVE, YZ16385BVE - page 23

    23 Section 4 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remov e key. Remov e spark plug w ire from spark plug and secure aw ay from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before w ...

  • Snapper YZ16385BVE, YZ16385BVE - page 24

    24 Section 4 - ADJUSTMENTS & REPAIR 4.5.5. BATTERY TESTING There are two types of battery tests: Unloaded and Loaded. The unloaded test is the procedure that will be discussed. It’s the simplest and most commonly used. An unloaded test is made on a battery without discharging current. To perform unloaded testing, check charge condition using ...

  • Snapper YZ16385BVE, YZ16385BVE - page 25

    25 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Starter Will Not Crank 1. Battery dead. 1. Service battery. Engine 2. Blown fuse. 2. Replace fuse. 3. Electrical connections loose or corroded. 3. C l ean and check connections for good contact. 4. Defective ignition sw itch. 4. Contact authorized SNA PPER dealer. 5. Blade engagement switc ...

  • Snapper YZ16385BVE, YZ16385BVE - page 26

    26 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Excessive Vibration 1. Damaged, out of balance or bent mo w er blades. 1. Service mower blade(s). 2. Loose blade components. 2. Service and tighten loose parts. 3. Loose or missing air lift (if equipped). 3. Replace air lifts. Tighten to proper torque. 4. Lumpy or fray ed belt. 4. Replace ...

  • Snapper YZ16385BVE, YZ16385BVE - page 27

    27 SERVICE SCHEDULE ITEM SERVICE PERFORMED REF. EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 7 X Initial Oil Change Page 11 X Periodic Oil Change Page 12 X* Oil Filter Initial Oil Change Engine Manual & Page 11 X Periodic Oil Change Engine Manual & Page 12 X* Air Pre-Cleaner Clean Sponge Element Engine Ma ...

  • Snapper YZ16385BVE, YZ16385BVE - page 28

    28 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the orig inal purchaser's residential, non-commercial use, SNAPPER , through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in materi ...

  • Snapper YZ16385BVE, YZ16385BVE - page 29

    29 PRIMARY MAINTENANCE ...

  • Snapper YZ16385BVE, YZ16385BVE - page 30

    30 PRIMARY MAINTENANCE ...

  • Snapper YZ16385BVE, YZ16385BVE - page 31

    31 PRIMARY MAINTENANCE ...

  • Snapper YZ16385BVE, YZ16385BVE - page 32

    32 PRIMARY MAINTENANCE ...

  • Snapper YZ16385BVE, YZ16385BVE - page 33

    33 SNAPPER PRODUCT REGISTRATION FORM IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS (Complete the following informa tion on your Snapper purchase) Model Number _____________________________________________________________ Serial Number _____________________________________________________________ Date of Pu rchase ______________________ ...

  • Snapper YZ16385BVE, YZ16385BVE - page 34

    34 NOTES ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ _ ...

  • Snapper YZ16385BVE, YZ16385BVE - page 35

    35 NOTES ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ _ ...

  • Snapper YZ16385BVE, YZ16385BVE - page 36

    36 NOTES ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ _ ...

  • Snapper YZ16385BVE, YZ16385BVE - page 37

    37 Safety Instructions & Operator’s Manual for SCRAMBLER HYDRO DRIVE SERIES 5 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contai n very important emissions information and critical safety warnings. Read, Understand, and Follo ...

Fabricante Snapper Categoría Lawn Mower

Los documentos del dispositivo Snapper YZ16385BVE, YZ16385BVE que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Snapper
- manuales de instrucciones YZ16385BVE, YZ16385BVE
- hojas de producto Snapper
- folletos informativos
- o etiquetas energéticas Snapper YZ16385BVE, YZ16385BVE
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Snapper YZ16385BVE, YZ16385BVE.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Snapper YZ16385BVE, YZ16385BVE, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Snapper YZ16385BVE, YZ16385BVE. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Snapper YZ16385BVE, YZ16385BVE.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Snapper YZ16385BVE, YZ16385BVE, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Snapper YZ16385BVE, YZ16385BVE. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Snapper YZ16385BVE, YZ16385BVE.

El manual de instrucciones completo de Snapper debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Snapper YZ16385BVE, YZ16385BVE - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Snapper YZ16385BVE, YZ16385BVE, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Snapper YZ16385BVE, YZ16385BVE que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Snapper YZ16385BVE, YZ16385BVE - que deben facilitarnos los primeros pasos durante el uso de Snapper YZ16385BVE, YZ16385BVE
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Snapper YZ16385BVE, YZ16385BVE
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Snapper YZ16385BVE, YZ16385BVE en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Snapper YZ16385BVE, YZ16385BVE?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Snapper YZ16385BVE, YZ16385BVE, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Snapper YZ16385BVE, YZ16385BVE probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)