-
Makita JV2000 - page 1
MODEL JVZOOO INSTRUCTION MANUAL DOUBLE INSULATION SPEC1 FICATIONS Max. cutting capacities in wood of stroke 20 mm 1 50" 6 mm 263 mm 1.6 kg (3/4") (2") 1 (114") 1 0-3'400 1 (10-3/8") (3.5 Ibs) * Manufacturer reserves the right to change specifications without notice Note: Specifications may differ from country to countr ...
-
Makita JV2000 - page 2
IMPORTANT I SAFETY INSTRUCTIONS TY SONAL READ REDLCE (For All Tools) PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- INJURY, INCLUDING THE FOLLOWING: ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 13. 2 WORK AREA CLEAN. Cluttered areas and benches invite injuries. IDER WORK AREA ENVIRONMENT. Don't ...
-
Makita JV2000 - page 3
14. F E I' 15. L 16. ( 17. $ t 18. ( F C r C E c I I' t 19. ( 20. F t I vo LT outle namc for tk the tl voltas IMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to !e that keys and adjusting wrenches are removed from tool before turning on. JOlD UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger I switch. Be sure ...
-
Makita JV2000 - page 4
ADDITIONAL SAFETY RULES 1. Avoid cutting nails. Inspect for and remove all nails from the workpiece be- 2. Don't cut hollow pipe. 3. Do not cut oversize workpiece. 4. Check for the proper clearance beneath the workpiece before cutting so that 5. Hold the tool firmly. 6. Check the blade is not contacting the workpiece before the switch is turne ...
-
Makita JV2000 - page 5
HOW TO USE Installing jig saw blade m Use the hex wrench to loosen the hex socket head bolt which holds the blade. Loosen I Fig 1 With the blade teeth facing forward, insert the blade into the blade holder as far as it will go. Make sure that the back edge of the blade fits into the roller and tighten the hex socket head bolt securely with the hex ...
-
Makita JV2000 - page 6
Switch action To start the tool, simply squeeze the switch lever. Release the lever to stop. Tool speed (0 to 3,400 RPM) is increased by increasing pressure on the lever. CAUTION : Before plugging in the tool, always check to see that the paddle switch actuates pro- perly and returns to the "OFF" position when released. Switch lever (Padd ...
-
Makita JV2000 - page 7
Operation Turn the tool on before contacting the workpiece. Then rest the base flat on the workpiece and gently move the tool for- ward along the previously marked cutting line. Plunge cutting Starting a cut at other than the edge of the workpiece without first drilling a starting hole requires a “plunge cut”. This can be accomplished by tippin ...
-
Makita JV2000 - page 8
Bevel cutting 1. With the base tilted, you can make bevel cuts at any angle between 0" and 45" (left to right). 2. Loosen the bolt on the back of the base with the hex wrench. Tilt the base to the desired angle. The edge of the hous- ing indicates the bevel angle. (Fig. IO). Then check for contact between the back edge of the blade and th ...
-
Makita JV2000 - page 9
Using guide rule (Rip fence) 1. When cutting widths of under 150 mm (6") repeatedly, use of the guide rule will assure fast, clean, straight cuts. 2. To attach the guide rule (rip fence), use the hex wrench to loosen the screw on the under side of the base in front, slip in the guide rule and secure the screw. Using circular guide 1. Use of th ...
-
Makita JV2000 - page 10
2. When attaching the circular guide, use the pin, inserting it in the center hole (arrow) and secure it with the threaded knob. The circular guide attaches to the base of the tool in the same manner as the guide rule (rip fence). Metal cutting Always use a suitable coolant (cutting oil) when cutting metal. Failure to do so will cause significant b ...
-
Makita JV2000 - page 11
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to about 4.5 mm (3/16") or less. Keep the brushes clean and free to slip in the holders. Both brushes should ...
-
Makita JV2000 - page 12
ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessortes or attachments might present a risk of injury to persons The accessories or attachments should be used only in the proper and intended manner. 0 Jig saw blade (packed 10 each in handy vinyl pou ...
-
Makita JV2000 - page 13
JIG SAW @" Model JV2000 hc.-18-'84 EN Note: The switch, noise suppressor and other part configurations may differ from country to country 13 ...
-
Makita JV2000 - page 14
MODEL JV2000 AtD DESCRIPTION Dec -18 84 US $s0ED DESCRIPTION MACHINE ~ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 1 6 1 1 1 1 1 1 1 1 2 1 4 1 1 1 1 1 2 1 1 1 1 1 1 I 1 1 2 1 1 1 - Pan Head Screw M5x8 IWifh Warherl Compresslo" spmg 4 Sleel Ball 4 PI" 4 Pin 4 Roller RelalMl sponge12 21 Blade Clamp ...
-
Makita JV2000 - page 15
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freigh ...
¿Tienes una pregunta acerca de Makita JV2000?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita JV2000, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita JV2000 probablemente compartirá una forma de solucionarlo.