Español dropdown-ico

Manual de instrucciones Seagate ST32430W

40 de páginas 0.29 mb
Descargar

Pasar a la página of 40

Summary
  • Seagate ST32430W - page 1

    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HA WK 2LP F amil y: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Wide bus) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST32430W/WD/WC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST32430DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST31 ...

  • Seagate ST32430W - page 2

    Contents Introduction ........................................................... 1 Electromagnetic interference ................................ 1 Before you begin .................................................. 3 Installation overview ............................................. 8 Product Repair ............................................... ...

  • Seagate ST32430W - page 3

    Hawk 2LP (Wide) Installation Guide, Rev. A 1 Introduction This manual is organized to assist you in the installation and operation of your Seagate Hawk 2LP (wide bus) family disc drive. Family models are listed in the Prod- uct Information section. It also provides information to aid in obtaining service for the drive. The Hawk 2LP (wide) family dr ...

  • Seagate ST32430W - page 4

    2 Hawk 2LP (Wide) Installation Guide, Rev. A and Regulations nor the Radio Interference Regula- tions of the Canadian Department of Communications. However, the unit has been tested using proper shield- ing and grounding and found to be compliant with the Class A limits of the FCC Rules and the Regulations of the Canadian Department of Communicatio ...

  • Seagate ST32430W - page 5

    Hawk 2LP (Wide) Installation Guide, Rev. A 3 Before you begin Verify that the system is switched off and discon- nected from main power before any installation is attempted. Protect yourself, the drive, and your valuable pro- grams and data by reading the following cautions and warnings. • Do not tamper with sealed top cover. Doing so voids your ...

  • Seagate ST32430W - page 6

    4 Hawk 2LP (Wide) Installation Guide, Rev. A • When transporting or shipping a drive or system, please ensure that they are correctly packed in original Seagate approved (or equivalent) container and shipped via an air-ride carrier experienced in handling computer equipment. • Do not unpack drive from its static shielded bag until you are ready ...

  • Seagate ST32430W - page 7

    Hawk 2LP (Wide) Installation Guide, Rev. A 5 C aution. The circuit assemblies and components con- tained in this equipment can be degraded or destroyed by Electrostatic Overstress (EOS) or by Electrostatic Discharge (ESD). Static electrical charges can accumulate quickly on personnel, clothing and synthetic materials. The electrostatic fields due t ...

  • Seagate ST32430W - page 8

    Safety instructions 1. The disc drive(s) are to be installed in a customer supplied enclosure where the surrounding air does not exceed 50 o C. 2. Four (4) 6-32 UNC-2A screws are required for installation. Maximum screw length into side of drive is 0.15 inches (3.81 mm). Maximum screw length into bottom is 0.20 in. (5.08 mm). Maximum screw tighteni ...

  • Seagate ST32430W - page 9

    Sicherheitsanleitung 1. Däs Gerät ist ein Einbaugerät, vorgesehen für eine maximale Umgebungstemperatur von 50 o C. 2. Zur Befestigung des Drives werden 4 Schrauben benötigt (6-32 UNC-2A). Die maximale Länge der Schrauben in der unteren Seite des Chassis darf nicht mehr als 0.20 in (5.08 mm) betragen, die in der oberen 0.15 in (3.81 mm). Maxi ...

  • Seagate ST32430W - page 10

    Installation Overview Installation of the drive can be divided into distinct phases. Some of these may not be applicable to all system installation requirements. Refer to the indi- vidual drive installation sections for specific information on your drive model. • Drive configuration: Select those drive features that are appropriate to install the ...

  • Seagate ST32430W - page 11

    • Low-Level formatting: All Hawk 2LP wide family drive models are low-level formatted at the factory and do not require this step during installation. If an installed drive is low-level formatted, all user data will be lost. Note: Seagate Technology assumes no liability for lost user data. • Partitioning and high level formatting: A drive can b ...

  • Seagate ST32430W - page 12

    Product repair information Service requirements The special facilities required for the manufacture of these drives generally prohibit repair in the field. If problems occur during installation, please contact your supplier for assistance. Do not attempt to disassemble or repair. Drives should be sent to the repair depot through the purchase source ...

  • Seagate ST32430W - page 13

    • Place drive on a flat, static dissipative surface and handle with extreme care. Always follow all EOS/ ESD precautions to avoid damage to the electrical assemblies. Shipping: When transporting or shipping a drive, a Seagate approved container must be used. Keep your original box. They are easily identified by the Seagate Ap- proved Package labe ...

  • Seagate ST32430W - page 14

    Warranty: Contact your Seagate Authorized Distribu- tor, Dealer or other purchase source for warranty information. If the drive is no longer under warranty contact pur- chase source for repair information or refer to numbers listed in section Technical Support Services. Technical support services Seagate Technology provides technical support litera ...

  • Seagate ST32430W - page 15

    SeaFone telephone number: 408/438-8222 The enhanced phone system provides recorded tech- nical information on selected Seagate products while you are on hold. Technical support specialists are available to answer questions from 8:00 AM to 5:00 PM PST, Monday through Friday. Recordings are acces- sible 24 hours a day, 7 days a week. SeaTDD telephone ...

  • Seagate ST32430W - page 16

    With this service you can access: • Specifications and jumper configurations for all Seagate products. • Reprints of Seagate documentation. • A directory of information and helpful utilities that you can download to your own computer. BBS Modem Location Number USA, Mexico, Latin America 408/438-8771 Canada 416/856-5581 England 44-62-847-8011 ...

  • Seagate ST32430W - page 17

    Hawk 2LP family (Wide) information Characteristics of the various drives covered by this manual are listed in the following table. Legend for table column meanings: A = capacity, unformatted megabytes B = capacity, formatted megabytes [1] C = number of cylinders, user accessible D = number of heads E = + 5 V typical current [2], Amps F = +12 V typi ...

  • Seagate ST32430W - page 18

    Initial setup information For the initial setup connect the cables or plug into a mounted connector (if applicable), set the drive ID on the bus and enable or disable the I/O line terminator resistor packs (Hawk 2LP family "W" models only). These procedures are described in paragraphs follow- ing. Note whether drive model number ends in W ...

  • Seagate ST32430W - page 19

    Hawk 2LP (Wide) Installation Guide, Rev. A 17 DC Power connection Hawk 2LP family "W/WD" model drives receive DC power through a 4 pin connector mounted on the PCB in line with the SCSI I/O connector. See figure below. Figure 1. DC power connection, 68 pin SCSI I/O connector Hawk 2LP "WC" and "DC" model drives receive ...

  • Seagate ST32430W - page 20

    18 Hawk 2LP (Wide) Installation Guide, Rev. A SCSI address selection On "W" and "WD" model drives, make sure that the SCSI bus address jumper(s) are properly set for the bus address assigned to the drive. See Figures 3a and 3b showing the bus address select header and the jumper configurations that select addresses 0 through 15. ...

  • Seagate ST32430W - page 21

    Terminator resistor packs As a factory installed option, Hawk 2LP family model "W" drives can have terminator resistor packs that are permanently installed, but can be enabled or disabled by jumper plug. See jumper in Figure 3a. If you are installing a single drive, the terminator resistor packs must remain enabled. If you are installing ...

  • Seagate ST32430W - page 22

    20 Hawk 2LP (Wide) Installation Guide, Rev. A Read/Write head auto-park Seagate disc drives described herein park the heads automatically at power off. This feature requires no operator intervention. Optional parity bit enable Some systems require parity bit checking. Consult the system documentation for the specific requirements. See Figure 3a for ...

  • Seagate ST32430W - page 23

    Hawk 2LP (Wide) Installation Guide, Rev. A 21 Figure 2a. Hawk 2LP family W/WD models I/O connection (68 pin SCSI I/O connector). "W" model terminators (not visible) are not removable. Figure 2b. Hawk 2LP family WC/DC model drive physical interface (80 pin SCSI I/O and DC power connector). Terminators are not provided. 68 Pin SCSI I/O Conn ...

  • Seagate ST32430W - page 24

    Drive configuration Each disc drive has option select header connectors on the back, side and front where jumper plugs are in- stalled to select the way that the drive is to be config- ured or to select its ID on the I/O bus. See "Initial setup information" and see notes following Figure 3c. Some host systems have a remote drive ID select ...

  • Seagate ST32430W - page 25

    Hawk 2LP family "WC" and "DC" model 80 pin SCSI I/O drives On Hawk 2LP family "WC" and "DC" model drives there is no J1-auxiliary connector. J6 can be used to set drive ID, but the host probably does it over the 80 pin interface. J6 can also be used to drive the external drive activity LED indicator signal. T ...

  • Seagate ST32430W - page 26

    24 Hawk 2LP (Wide) Installation Guide, Rev. A Drive with HDA up, PCB down, viewed from front Pin 1 HDA J6 [1] SCSI ID = 0 SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6 SCSI ID = 7 Reserved J1-DC Power Connector J2 Drive Front Pin 1 End J6 SCSI I/O Connector J1-SCSI I/O Pin 1 J2 A 2 A 1 J1-Auxiliary A 0 See ? ...

  • Seagate ST32430W - page 27

    Hawk 2LP (Wide) Installation Guide, Rev. A 25 J1-DC Power J1 68 Pin SCSI I/O Connector Drive HDA SCSI ID = 8 SCSI ID = 9 SCSI ID = 10 SCSI ID = 11 SCSI ID = 12 SCSI ID = 13 SCSI ID = 14 SCSI ID = 15 A 3 A 2 A 1 SCSI ID = 0 SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6 SCSI ID = 7 A 0 [3] J1-Auxiliary Pin 1A  ...

  • Seagate ST32430W - page 28

    J2 Drive Front Pin 1 End J6 Pin 1 J2 J1 Delay Motor Start Enable Motor Start Write Protect Parity Option Jumper Positions T E D S M E W P P E S S T P T P [8] [8] Pin 1 HDA Drive with HDA up,  PCB down, viewed from front J6 [1] +5V Ground SCSI ID = 0 SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = ...

  • Seagate ST32430W - page 29

    Notes for Figure 3a, 3b and 3c: [1] Notes explaining the functions of the various jump- ers on jumper header connectors J2, J1-auxiliary and J6 are given below in left to right order of jumper position. The term " default " means as standard OEM units are configured when shipped from fac- tory. "Off" means no jumper is installed ...

  • Seagate ST32430W - page 30

    28 Hawk 2LP (Wide) Installation Guide, Rev. A [4] The drive time-shares the ID and BUSY LED func- tions of J6 and J1-auxiliary. That is, a cable may be attached to one of these headers to pick up the signal that lights the external BUSY LED indicator. If lines for external ID selection are not also in- cluded in the cable, jumper plugs must be used ...

  • Seagate ST32430W - page 31

    Hawk 2LP (Wide) Installation Guide, Rev. A 29 continued from previous page DS ME Off Off Spindle starts immediately after power up - Default setting. Off On Drive spindle does not start until Start Unit command received from host. On Off Spindle Start-up is delayed by SCSI ID times 12 seconds after power is applied, i.e., drive 0 spindle starts imm ...

  • Seagate ST32430W - page 32

    continued from previous page SS Off On Reserved. Default is no jumper installed. TP TP (Not applicable to "WC/DC" model drives) Off Off No terminator power is connected to drive terminators or SCSI bus I/O pin 26. On Off Drive supplies its own terminator power only. Jumper on this position is factory default. Off On Drive supplies power t ...

  • Seagate ST32430W - page 33

    Hawk 2LP (Wide) Installation Guide, Rev. A 31 continued from previous page I/O pin 26 to the drive's internal termina- tors (for single-ended I/O only). Off See above explanations for TP jump ers. J1-Auxiliary Jumper Jumper Function Description ("W" Installation and "WD" models only) A 3 ,A 2 ,A 1 ,A 0 Drive ID on SCSI Bus ...

  • Seagate ST32430W - page 34

    32 Hawk 2LP (Wide) Installation Guide, Rev. A continued from previous page future time when the ID is changed the user could fail to configure both the same. Default is ID = 0. For "WC" and "DC" models refer to Note [7]. Models "W" and "WD" only BUSY These pins used to connect a cable for a LED remote BUSY LE ...

  • Seagate ST32430W - page 35

    Hawk 2LP (Wide) Installation Guide, Rev. A 33 Drive installation This section describes the physical mounting of the drive in the host cabinet and the logical installation as a system member, which is called drive setup. Disc drive mounting Do not touch the connector pins or any PCB compo- nents without observing static-discharge precautions. Alway ...

  • Seagate ST32430W - page 36

    34 Hawk 2LP (Wide) Installation Guide, Rev. A B J H K [2] Notes: [1] [2] [3] [4] Inches Millimeters 5.74 4.00 1.00 2.362 .620 4.000 .250 1.750 3.750 2.370 1.00 4.000 0.19 0.015 145.80 101.60 25.40 60.00 15.75 101.60 6.35 44.45 95.25 60.20 25.40 101.60 4.83 0.381 A B C D E F G H J K L M N P ± ± + – ± ± ± + – ± ± ± ± ± ± max 0.010 0.01 ...

  • Seagate ST32430W - page 37

    Hawk 2LP (Wide) Installation Guide, Rev. A 35 A F D E [1] [3] B G Inches A B C D E F G H J K L 145.80 101.60 25.40 60.00 15.75 101.60 6.35 44.45 95.25 60.20 4.597 J H K [2] 5.74 4.00 1.00 2.362 .620 4.000 .250 1.750 3.750 2.370 0.181 ± .010 ± .010 + .026 – .010 ± .010 ± .010 ± .010 + .010 – .005 ± .010 ± .010 ± .010 + .018 – .013 ± . ...

  • Seagate ST32430W - page 38

    36 Hawk 2LP (Wide) Installation Guide, Rev. A Do not power up the host system until the drive is mounted and the system cover is replaced. • Connect DC power connector to the drive ("W/WD" models only). • Replace the Host System cover. • Turn on DC power. • Boot the system from the floppy drive or from a previously installed hard- ...

  • Seagate ST32430W - page 39

    Hawk 2LP (Wide) Installation Guide, Rev. A 37 SCSI interface drives The SCSI interface handles both drive geometry and defect management internally. The "no drive installed" option is selected for systems with SCSI drives. All SCSI interface drives are low-level formatted at the factory. You may wish to low-level format the drive to optim ...

  • Seagate ST32430W - page 40

    Seagate Technology, Inc. 920 Disc Drive, Scotts Valley, CA. 95066-4544, USA Publication Number: 77767478, Rev. A Printed in USA ...

Fabricante Seagate Categoría Computer Drive

Los documentos del dispositivo Seagate ST32430W que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Seagate
- manuales de instrucciones ST32430W
- hojas de producto Seagate
- folletos informativos
- o etiquetas energéticas Seagate ST32430W
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Seagate ST32430W.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Seagate ST32430W, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Seagate ST32430W. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Seagate ST32430W.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Seagate ST32430W, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Seagate ST32430W. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Seagate ST32430W.

El manual de instrucciones completo de Seagate debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Seagate ST32430W - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Seagate ST32430W, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Seagate ST32430W que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Seagate ST32430W - que deben facilitarnos los primeros pasos durante el uso de Seagate ST32430W
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Seagate ST32430W
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Seagate ST32430W en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Seagate ST32430W?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Seagate ST32430W, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Seagate ST32430W probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)