-
Alpha Tool.Com.HK Limited ECOGRDGR - page 1
Part No: ECOGRDGR V ersion 1 103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-01 14 www .alpha-tools.com Alpha ® Ecoguar d T ype G Dust Collection Co v er Instr uction Manual MANUAL (*Shown with angle grinder / sold separately) ...
-
Alpha Tool.Com.HK Limited ECOGRDGR - page 2
2 T ABLE OF CONTENTS Introduction .................................................................................3 About the Symbols ...............................................................3 Ecoguard T ype G Overview ........................................................4 Accessories ...................................................... ...
-
Alpha Tool.Com.HK Limited ECOGRDGR - page 3
3 INTRODUCTION Thank you for purchasing the Alpha ® Ecoguard T ype G Dust Collection Cover . The Ecoguard T ype G must be used with a vacuum, or other dust collection system. T o ensure correct use, read this Instruction Manual and the Instruction Manual for the power tool and follow the operating instructions. Keep this manual in a place where op ...
-
Alpha Tool.Com.HK Limited ECOGRDGR - page 4
4 Stainless Steel Hose Band Rubber Hose Adapter ECOGUARD TYPE G OVER VIEW ACCESSORIES Ecoguard Dust Collection Cover w/ Connector (Part# 500028) ..... 1 pc Collar .............................................................................................2 pcs Additional Connector Assembly for Most 5” Grinders ....................2 pcs Flanges a ...
-
Alpha Tool.Com.HK Limited ECOGRDGR - page 5
5 INST ALLING THE DUST COLLECTION COVER W ARNING! Be sure to turn off the high-speed angle grinder and remove the plug from the electrical outlet before attaching and installing the Dust Collection Cover . T ake the Guard off from the Grinder Make sure the Dust Collection Cover is securely attached, otherwise it may come loose which could cause inj ...
-
Alpha Tool.Com.HK Limited ECOGRDGR - page 6
6 If the different Connector is needed, exchange the connector as per the following instructions. Loosen the Screws. T ake the front of the Connector Assembly off. Loosen the Flat Head Screws using the Hex Wrench. T ake the back of the Connector Assembly off. Replace with other Connector . Place in the other Connector 1. 2. 3. 4. 5. 6. Ecoguard T y ...
-
Alpha Tool.Com.HK Limited ECOGRDGR - page 7
7 Assembly . T ighten Flat Head Screws with Hex Wrench. (DO NOT forget to insert T aper W ashers) Hex-Wrench Flat Head Screw T ighten the Screws (DO NOT forget to insert Spring W ashers) 7. 8. T aper W asher Screw M4x10 ...
-
Alpha Tool.Com.HK Limited ECOGRDGR - page 8
8 Connector Assembly CAUTION! The Dust Collection Cover is solely designed for use with a grinding cup wheel. Do not use with any other type of blade, such as a cutoff or tip saw blades. MOUNTING THE GRINDING CUP WHEEL T O THE GRINDER W ARNING! Make sure the Ecoguard T ype G is securely atttached to the grinder , otherwise it may come loose, causin ...
-
Alpha Tool.Com.HK Limited ECOGRDGR - page 9
9 Set the proper Spacer into the spindle. Set the Base or Inner Flange on the Spacer . Set the Grinding Cup Wheel on the Base or Inner Flange. Set the Lock Nut on the Grinding Cup Wheel. (Be careful to ensure the correct direction of the Lock Nut) Depress the spindle and tighten the Lock Nut with the Pin Wrench. 2. 3. 4. 5. 2. Grinding Cup Wheel Pi ...
-
Alpha Tool.Com.HK Limited ECOGRDGR - page 10
10 Choose proper Spacer to Keep X and Y as below: 1<X<5 1< Y Reference: Example of the combination of Spacer and Base Flange CUP T ype Parts ALPHA ® MAKIT A ® HIT ACHI HSG-125 9565CV 9558NB G12S43 G13SE2 Flange 500029 Lock Nut Original Spacer 50001 1 / T2.5 N/A 50001 1 / T2.5 Flange 500029 Lock Nut Original Spacer 50001 1 / T2.5 N/A 5000 ...
-
Alpha Tool.Com.HK Limited ECOGRDGR - page 11
11 GRINDING APPLICA TIONS SURF ACE GRINDING Securely connect the Flexible Connector Hose to the Dust Collection Cover . T urn Grinder and V acuum on to start grinding application. Use the Alpha ® Rubber Hose Connector as a joint between duct and Flexible Connector Hose. W ALL GRINDING Loosen the screws and remove the Sub Cover and Half Cover . 1. ...
-
Alpha Tool.Com.HK Limited ECOGRDGR - page 12
12 Switch the position of the Sub Cover and Half Cover . T ighten screws. A TT ACHING THE DUST COLLECT OR Securely connect Flexible Connector Hose to the duct of the grinder , then turn Grinder and V acuum Cleaner on to start grinding application. Use an adapter such as the Alpha ® Rubber Hose Connector as a joint between the duct and the Flexible ...
-
Alpha Tool.Com.HK Limited ECOGRDGR - page 13
13 ALPHA ® ECOGUARD TYPE G SCHEMA TIC ALPHA ® / MAKIT A ® CONNECTOR, SP ACERS AND FLANGE / LOCK NUT *Original indicates Lock Nut included with tool. ...
-
Alpha Tool.Com.HK Limited ECOGRDGR - page 14
14 *Original indicates Lock Nut included with T ool. # 1 1-a,b,c,d - Choose spacer according to Cup T ype. (See chart on page 10) ECOGUARD TYPE G OTHER CONNECT ORS AND SP ACERS ...
-
Alpha Tool.Com.HK Limited ECOGRDGR - page 15
15 ALPHA ® ECOGUARD TYPE G P ARTS LIST DRA WING NO. P ART NO. DESCRIPTION QUANTITY 1 500032 Main Cover 1 2 500033 Sub Cover 1 3 500034 Half Cover 1 4 500005 Rubber Hose Adapter 1 5 500006 Stainless Steel Hose Band 1 6 500037 Screw M4x10 4 7 500038 Set Plate 1 8 500039 Holder Spring 4 9 500020 Flat Head Screw M4x5 3 10a 500028 Connector Assembly (A ...
-
Alpha Tool.Com.HK Limited ECOGRDGR - page 16
Copyright © 2010 Alpha Professional T ools. All rights reserved. 103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-01 14 www .alpha-tools.com 10/2010 ...
¿Tienes una pregunta acerca de Alpha Tool.Com.HK Limited ECOGRDGR?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Alpha Tool.Com.HK Limited ECOGRDGR, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Alpha Tool.Com.HK Limited ECOGRDGR probablemente compartirá una forma de solucionarlo.